Research on a six-phase permanent magnet synchronous motor system at dual-redundant and fault tolerant modes in aviation application

With the development of more/all electrical aircraft technology,an electro-mechanical actuator (EMA) is more and more used in an aircraft actuation system.The motor system,as the crucial part of an EMA,usually adopts the redundancy technology or fault tolerance technology to improve the reliability.To compare the performances of these two motor systems,a 10-pole/ 12-slot six-phase permanent magnet synchronous motor (PMSM) is designed with the concentrated single-layer winding,which is able to operate at dual-redundant and fault tolerant modes.Furthermore,the position servo performances of the six-phase PMSM at dual-redundant and fault tolerant modes are analyzed,including the normal and fault conditions.In addition,a variable structure proportional-integral-derivative (PID) control strategy is proposed to solve the performance degradation problem caused by phase current saturation.Simulation and experimental results show that the fault tolerant PMSM has a better position servo performance than the dual-redundant PMSM,and the variable structure PID control strategy is able to improve the performance due to phase current saturation.     

Design and analysis of a novel hybrid cooling method of high-speed high-power permanent magnet assisted synchronous reluctance starter/generator in aviation applications

To improve the heat dissipation performance, this paper proposes a novel hybrid cooling method for high-speed high-power Permanent Magnet assisted Synchronous Reluctance Starter/Generator (PMaSynR S/G) in aerospace applications. The hybrid cooling structure with oil circulation in the housing, oil spray at winding ends and rotor end surface is firstly proposed for the PMaSynR S/G. Then the accurate loss calculation of the PMaSynR S/G is proposed, which includes air gap friction loss under oil spray cooling, copper loss, stator and rotor core loss, permanent magnet eddy current loss and bearing loss. The parameter sensitivity analysis of the hybrid cooling structure is proposed, while the equivalent thermal network model of the PMaSynR S/G is established considering the uneven spraying at the winding ends. Finally, the effectiveness of the proposed hybrid cooling method is demonstrated on a 40 kW/24000 r/min PMaSynR S/G experimental platform.     

某探测器上火箭发动机热防护仿真与设计

根据某探测器的具体结构及工作条件,分析和计算探测器上火箭发动机的热环境参数.利用有限元法计算火箭发动机固壁辐射热流密度,依据热流边界条件设计热防护方案;利用有效发射率表征多层隔热材料隔热性能并进行温度场数值仿真.由于多层隔热材料性能参数的不易确定性,计算了参数在较大范围内的热防护效果.通过仿真计算验证热防护方案的有效性和可靠性,并分析影响热防护效果的主要因素;计算结果表明多层隔热材料的有效发射率是影响隔热性能最重要的因素,比热容、表面发射率、密度对热防护性能影响很小.      

超磁致伸缩电静液作动器磁场分析与优化

提出一种超磁致伸缩电静液作动器（GMEHA）结构,采用永磁体与控制线圈组合提供驱动磁场.首先建立了该组合磁路数学模型,并给出了超磁致伸缩棒内磁感应强度计算解析式;其次,对以上结构进行了有限元分析（FEA）,得出了磁路主要结构参数与磁场分布均匀性之间映射规律;最后进行了作动器磁场试验研究并与有限元分析结果进行了对比,验证了理论与有限元模型的可预测性,给出了该电静液作动器结构设计方法.结果表明:该电静液作动器的最佳驱动频率为250Hz,最大无负载体积流量为0.85L/min,最大阻断力达到了120N.      

空载固体发动机计算与试验模态相关性分析

为了预测空载状态固体火箭发动机动态特性,对其进行了模态试验,并应用MSC.Marc进行了模态计算,然后对比两者的结果,进行了相关性分析和评估。计算得到了发动机250Hz以内的一阶弯曲模态和五阶呼吸模态。试验测得了发动机的三阶呼吸模态和一阶弯曲模态。比较试验测试模态和与之对应的计算模态:固有频率相对误差均在5%以内;振型相关图上的点大都分布在斜率为1(或 1)的直线周围;MAC(模态置信判据)值在0 9左右。说明计算与试验模态有较好的相关性,有限元计算模型比较准确的反映了实际情况。     

稳态等离子体推力器磁场设计与数值分析

首先分析了稳态等离子体推力器性能对磁场的要求，据此介绍了磁路系统的工程设计原则和方法；然后，采用ANSYS大型有限元分析软件对一个具体的稳态等离子体推力器在额定工况下的磁场进行了计算，获得了满意的结果，通过对结果的分析获得了对有关现象的直观深入的认识，为所计算具体推力器的改进设计提供了线索；同时，也证实了以ANSYS为软件平台的稳态等离子体推力器磁路系统计算机数值仿真辅助设计的可行性和有效性。     

模块化永磁直线游标电机等效磁网络及漏磁分析

在模块化永磁直线游标电机的初始设计及优化设计中,使用有限元方法(FEM)计算漏磁系数时需要耗费大量的建模和计算时间。针对这一问题,建立该种电机的等效磁网络模型,在建模期间,考虑气隙中的边缘效应,并计算永磁体组与定子齿在不同相对位置时的等效磁导,得到该种电机在一个周期内不同相对位置时的漏磁磁导和漏磁系数的数学解析表达式。采用FEM验证了该数学解析表达式的准确性。研究结果为模块化永磁直线游标电机的设计提供了理论依据。     

Modeling and analysis of mover gaps in tubular moving-magnet linear oscillating motors

A tubular moving-magnet linear oscillating motor (TMMLOM) has merits of high efficiency and excellent dynamic capability. To enhance the thrust performance, quasi-Halbach permanent magnet (PM) arrays are arranged on its mover in the application of a linear electro-hydrostatic actuator in more electric aircraft. The arrays are assembled by several individual segments, which lead to gaps between them inevitably. To investigate the effects of the gaps on the radial magnetic flux density and the machine thrust in this paper, an analytical model is built considering both axial and radial gaps. The model is validated by finite element simulations and experimental results. Distributions of the magnetic flux are described in condition of different sizes of radial and axial gaps. Besides, the output force is also discussed in normal and end windings. Finally, the model has demonstrated that both kinds of gaps have a negative effect on the thrust, and the linear motor is more sensitive to radial ones.