基于管制员负荷的西安终端区扇区优化

若扇区的工作负荷差别较大,会限制空域容量,给飞行安全和空域的利用造成不利影响.为了提高空域容量,缓解空中交通压力,构建基于管制员负荷的西安终端区扇区优化方法.通过对西安终端区近期雷达数据进行统计分析、量化管制负荷,得到符合西安终端区的管制员负荷综合值;对该终端区进行剖分得到Voronoi图,依据均衡扇区管制负荷的原则,加入实际约束条件,采用遗传算法对扇区进行优化.结果表明:通过扇区优化,提升了西安终端区的容量,均衡了各扇区的管制负荷,取得了较好的优化效果.     

基于整数规划的终端区空域扇区划分研究

扇区划分是终端区空域规划的研究内容之一,划分后能覆盖不均匀的交通分布,缓解需求与容量的不平衡,从而提高空域系统的运行效率。将终端区扇区划分作为一个整数规划问题,在约束条件中考虑了间隔规则、飞行路径需求和机场跑道结构的几何约束等,根据最优解来生成终端区扇区。以某终端区算例,验证了整数规划模型的可行性。     

重庆机场终端区容量评估的仿真研究

确定和提高终端区容量,对减少航班延误和保障飞行安全有着较高的意义。考虑终端区系统自身的复杂性和影响因素的随机性,当前多采用计算机仿真技术对终端区容量进行评估。使用SIMMOD PLUS仿真软件对重庆机场系统和终端区系统进行联合仿真,结合当地管制工作负荷情况以及流量控制策略,对重庆机场终端区容量的大小进行评估。并对SIMMOD PLUS软件给出的各个节点延误量进行统计分析,找出了限制终端区运行的瓶颈所在,设计相应的空域结构优化方案,实现提升终端区容量的目的。仿真结果表明,方案合理、有效。     

首都机场终端区多进港队列排序优化策略与仿真

在现行可用空域中，通过流量管理策略与进港航班队列优化相结合可提高机场运行容量。以终端区航路航线间隔和扇区容量为约束，通过合理分配机场终端区边界的进港口流量．以总进场排队等待时间最短为目标，提出了协同调配流量和机动分流两种新策略，达到提高机场运行效率的目的。以首都机场为例，利用计算机仿真验证，结果表明：与现状运行相比较采用的优化策略排队进场可使进场延误和等待时间减少，并使离场正常率提高8％左右。     

基于AirTOp的区域点融合程序运行效益评估

为了科学、快速地评估点融合技术在区域管制扇区的应用效益,为民航空域管理部门提供客观、科学的参考数据,选取合适的评估指标和建立可靠的扇区空域结构仿真模型具有重要意义.以区域管制扇区为例,分别构建了区域现行空域结构和点融合空域结构模型,并设计了相应的仿真场景,根据实际的运行规则和航班流对比研究了不同空域结构下的运行情况.仿...     

基于管制员工作负荷的终端区容量评估

对现有的基于管制员工作负荷的空域容量评估方法进行分析,并比较各自的特点。提出了改进的基于管制员工作负荷的容量评估模型,模型的建立不仅考虑了管制员工作负荷的不同类别,即通信负荷、非通信负荷和思考负荷,还考虑了空域内航路结构的复杂性,即区分空域内不同航路走向上运行的航空器数量。描述了基于新建模型的容量评估方法。以哈尔滨机场终端区为背景,在雷达管制的基础上,使用新建立的模型,采用回归分析方法,计算了终端区容量,验证了所提模型和方法的可行性与适用性。     

基于空中交通管制运行品质的扇区容量评估

扇区容量反映的是扇区空中交通管制运行品质诸多要素综合寻优下的流量水平,目前将扇区管制员工作负荷阈值映射为扇区容量的评估方法存在片面性。为改善扇区容量评估方法,以成都进近南扇为研究实例,采集198组实际运行数据建立样本集,确立了涵盖空中交通流密度、管制运行安全性能、管制运行效率性能及管制员工作负荷等4类因子的管制运行品质量化指标,并基于主成分分析法实现了扇区管制运行品质综合评价,经函数拟合确定扇区容量为29架次/h,新方法更具科学性、客观性。     

空域扇区网络级联失效抗毁性及优化策略

应用复杂网络理论,从系统层面研究空域扇区网络的级联失效抗毁性,提出空域扇区网络级联失效抗毁性优化策略,以提升空域扇区网络级联失效抗毁性。首先,定义空域扇区网络节点负载和容量,分析空域扇区网络级联失效过程并建立模型,确立临界阈值和扇区非正常率为级联失效测度指标。然后,根据管制扇区运行特点,提出2种优化策略——基于扇区节点剩余容量的相邻负载再分配策略和局部负载再分配策略。通过仿真,分析了参数变化规律与网络抗毁性的关系,证明局部负载再分配策略可以大幅提升空域扇区网络级联失效抗毁性。     

军事活动影响下的终端区容量评估方法研究

准确地预测军事活动影响下的空域容量对于缓解军民航用空矛盾冲突具有重要意义。通过对飞机机动动作的分析,给出飞行受限区的划设方法;利用改进的遗传算法从定量的角度对军事活动影响下的空域容量 进行评估;以某机场终端区为例,对终端区容量进行仿真实验。结果表明：改进的遗传算法能够有效避免传统算法计算量指数级增长的局限性,在保证准确性的同时可以提高运算的效率。     

军航活动下扇区动态容量评估研究

民航业迅速发展,空域资源的稀缺性日益凸显。科学合理地评估空域容量是解决空中交通流量瓶颈的关键,同时也为制定流量管理策略提供科学的依据。由于我国体制的特殊性,军航活动一直是我国空域资源限制的重要因素。研究并详细分析军航活动对扇区容量损失作用的机理,定量地评估军航活动对扇区容量的影响,建立军航活动影响下的扇区动态容量评估模型,结论表明模型有一定的参考意义。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.