多核操作系统自旋锁技术研究

多核操作系统通常采用自旋锁技术保证多核之间互斥.处理器核属于硬件设备,需要硬件锁机制实现核间互斥,各类处理器都提供相应的硬件指令实现自旋锁,如锁总线.处理器核在获取自旋不成功时,一直自旋,直到获取锁成功.自旋锁持有时间非常短,不引起睡眠,效率很高.     

基于多分区操作系统的多核确定性调度方法设计

为提高多分区操作系统环境下多核处理器的应用带来的操作系统任务调度的确定性,研究了多分环境下多核操作系统结构,从处理器核心和分区的资源分配和分区调度表的时间同步角度出发,采用了静态配置、处理器绑定和时间窗口调度方法,实现了处理器资源的确定性分配,解决了调度表之间的时间同步问题。测试结果表明,方法有效提高了分区环境下多核操作系统任务调度的确定性。     

基于对称多处理架构的软件调试技术研究和实现

为了满足计算机领域用户对高性能及低功耗的双重需求,在深入研究多核现状的基础上,结合核间中断技术,提出了一种对称多处理架构下的软件调试器设计和实现方案。方案不仅成本低,而且不需要特殊调试硬件的支持,可为多核系统的故障诊断和分析提供参考借鉴。     

嵌入式多核操作系统确定性研究

为解决嵌入式多核操作系统确定性问题,详细阐述了计算确定性,重点分析了多核结构引入的不确定性问题。通过研究嵌入式多核操作系统的结构,从共享存储的确定性访问、确定性任务调度、确定性通信等方面提出了解决多核结构带来的不确定性问题的方法。     

一种多核分区操作系统的绑定组调度方法

伴随机载计算平台对算力提升的显著需求,综合化模块化航空电子系统(IMA)采用多核处理器和相应的多核分区操作系统成为必然趋势,从而对目前仅适用于单核处理模式的多分区调度算法产生了进一步的能力扩展需求。面向多核处理的多分区调度算法需要在发挥多核处理效能的同时,继续维持机载安全关键系统的实时性和确定性特征。为此,提出一种基于...     

基于分区代理机制的FC通信虚拟化方案设计

随着航电系统的发展,处理平台的集成度逐步提高,多核处理器集成多个应用将是未来应用的趋势。 但在使用多核处理器的系统中,由于多个处理器核并行运行,需要解决通信资源在多个处理器核之间的共享问 题。本文提出了一种基于分区代理机制的FC 通信虚拟化方案设计,可以实现多核架构下多应用、多分区共享 FC 网络接口设备进行通信。     

机载嵌入式系统中的多核处理架构研究与分析

与单核处理器相比较,多核处理器在性能、功耗、体积以及重量各方面都有绝对的优势,这使得多核处理器在机载嵌入式系统中的应用成为必然趋势。在分析了航空电子系统的任务特点之后,介绍了两种最常见的多核处理器系统架构：对称多处理（SMP）和非对称多处理（AMP）,对这两种系统架构在机载嵌入式系统的应用进行了研究分析,并分析了其关键技术对实时性、安全性和确定性的影响。     

TMS320C6678多核DSP的加载配置和实现方法

程序代码正确的固化加载运行是多核DSP应用的前提和基础.简要介绍了DSP的加载器和加载过程,阐述了多核处理器件的加载配置管理方法.以TI公司的多核DSP TMS320C6678为例,介绍了多核DSP的加载模式和流程,详细阐述了EMIF16的Nor FLASH加载实现方法,可以实现多核DSP软件的正确、可靠加载运行.     

文件系统通用技术框架设计

传统的文件系统产品多样,对操作系统服务依赖性强,跨平台应用能力差,针对此问题提出一种文件系统通用技术框架。该框架结构设计文件管理接口层用于提供通用标准接口的访问及多种类型文件系统的统一管理;设计平台抽象层用于屏蔽底层存储设备及操作系统的差异,实现异构平台支持。测试验证表明该框架设计能够实现异构平台下通用文件系统设计,能够实现操作系统、存储设备、不同文件系统的抽象,以较小的改动实现多平台支持,并逐渐实现代码复用减少研发成本。     

一种多核实时图像处理模块设计与实现

实时图像处理能力是嵌入式系统中影响系统性能的核心因素.为充分挖掘多核DSP性能,从计算机系统结构的角度出发,开展对多核DSP实时图像处理体系结构的研究,设计了一种基于TMS320 C6678的实时图像处理模块.采用FPGA进行实时图像的采集和缓存,利用四线RapidIO高速接口完成FPGA与DSP之间的数据传输,并设计了四级图像缓冲流水处理结构,实现了图像采集、缓存、处理和发送的并行进行.设计了一套基于数据块共享的实时图像处理多核协同处理机制,可以充分利用C6678八个核的优势,实现对图像的实时处理.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.