STAP with medium PRF mode for non-side-looking airborne radar

Space-time adaptive processing (STAP) has been widely discussed for airborne radar systems to improve the system performance of detecting targets. This is especially true for airborne early warning (AEW) radar, which should find long-range and small radar cross section (RCS) targets such as the stealth aircraft and missiles. However, in existing airborne radar literature, STAP is mainly considered for clutter and jamming rejection in side-looking airborne radar (SLAR) applications. There have been fewer discussions on airborne radar with non-side-ways looking array radar (non-SLAR). The STAP of non-SLAR such as forward looking array radar is also very important and can not be avoided for airborne radar to detect targets in all directions. The STAP of the non-SLAR is studied here. A scheme has been proposed, which is processed by the way of STAP combined with multiple staggered medium pulse repetition frequencies (PRFs). We further study the selection of PRFs in order to make the scheme more available for non-SLAR radar. We analyze two typical non-SLAR cases, i.e., inclined-sideways looking array and forward looking array. We examine this scheme by comparing the performances of three processing systems under the criteria of range-velocity blind zone minimization. Computer simulation results show the multiple-PRFs STAP scheme is feasible for non-SLAR and can be applied to phased-array AEW radar systems     

基于杂波子空间估计的MIMO雷达降维STAP研究

 多输入多输出(MIMO)雷达是近年来出现的一种新体制雷达,针对MIMO体制的机载雷达开展空时自适应处理（STAP）技术研究是值得进一步努力的方向。本文研究了机载MIMO雷达STAP技术的降维算法,通过对STAP技术杂波抑制原理进行分析,推导并得到一种基于杂波子空间的降维算法。结合扁长椭球波函数（PSWF）的特点,提出了一种基于杂波子空间估计的降维算法,并与若干降维算法的杂波抑制性能进行比较。结果表明,当存在阵元幅相误差时,该算法在保持杂波抑制性能的同时能够有效地降低STAP算法的运算量。     

一种基于角度-多普勒补偿的均匀圆形天线机载雷达杂波抑制方法

采用均匀圆形相控阵天线的机载雷达杂波分布随距离变化而变化,各距离单元的杂波不再满足独立同分布的条件,造成统计型空时自适应处理(STAP)器性能下降。基于此,本文建立了均匀圆形天线机载雷达模型,对其杂波分布进行了分析,得出了空间角随阵元数非线性变化的特性造成其杂波距离维分布非均匀的结论。研究了一种均匀圆形天线机载雷达杂波抑制方法,该方法先通过修正的角度 多普勒补偿(MADC)预处理消除在杂波谱中心处的非均匀,再利用基于导数更新(DBU)技术进一步减小在其他方位杂波的非均匀程度。仿真结果表明了该方法的有效性。     

Implementing digital terrain data in knowledge-aided space-time adaptive processing

Many practical problems arise when implementing digital terrain data in airborne knowledge-aided (KA) space-time adaptive processing (STAP). This paper addresses these issues and presents solutions with numerical implementations. In particular, using digital land classification data and digital elevation data, techniques are developed for registering these data with radar return signals, correcting for Doppler and spatial misalignments, adjusting for antenna gain, characterizing clutter patches for secondary data selection, and ensuring independent secondary data samples. These techniques are applied to select secondary data for a single-bin post-Doppler STAP algorithm using multi-channel airborne radar measurement (MCARM) program data. Results with the KA approach are compared with those obtained using the standard sliding window method for choosing secondary data. These results illustrate the benefits of using terrain information, a priori data about the radar, and the importance of statistical independence when selecting secondary data for improving STAP performance     

Knowledge-based space-time adaptive processing for airborne earlywarning radar

This paper describes an innovative concept for knowledge-based control of space-time adaptive processing (STAP) for airborne early warning radar. The knowledge-based approach holds potential for significant performance improvements over classical STAP processing in nonhomogeneous environments by taking advantage of a priori knowledge. Under this approach, knowledge-based control is used to direct pre-adaptive filtering, and to carefully select STAP algorithms, parameters, and secondary data cells     

非正侧视阵列机载雷达多空间角补偿算法

 非正侧阵列机载雷达的杂波分布随距离变化而变化,各距离单元的杂波分布不再满足独立同分布条件,造成统计型空时自适应处理(STAP)处理器性能下降。本文提出了一种多空间角补偿(MSAC)的非正侧视机载雷达杂波抑制方法,该方法先通过角度-多普勒补偿(ADC)预处理以消除在谱中心处的杂波非均匀,然后采用MSAC法在多个多普勒方向使参考单元和待检测单元的杂波谱保持一致,从而进一步消除在其余方位的杂波非均匀。仿真结果表明了该方法的性能明显优于ADC法,且运算量增加不多。     

Reduced-rank STAP for high PRF radar

Due to the range ambiguity of high pulse-repetition frequency (HPRF) radars, echoes from far-range fold over near-range returns. This effect may cause low Doppler targets to compete with near-range strong clutter. Another consequence of the range ambiguity is that the sample support for estimating the array covariance matrix is reduced, leading to degraded performance. It is shown that space-time adaptive processing (STAP) techniques are required to reject the clutter in HPRF radar. Four STAP methods are studied in the context of the HPRF radar problem: low rank approximation sample matrix inversion (SMI), diagonally loaded SMI, eigencanceler, and element-space post-Doppler. These three methods are evaluated in typical HPRF radar scenarios and for various training conditions, including when the target is present in the training data     

Eigenstructure-based algorithms for direction finding withtime-varying arrays

This paper considers the problem of finding the directions of narrowband signals using a time-varying array whose elements move during the observation interval in an arbitrary but known way. We derive two eigenstructure-based algorithms for this problem, which are modifications of techniques developed originally for time-invariant arrays. The first uses array interpolation, and the second uses focusing matrices. Like other eigenstructure-based methods, these algorithms require a modest amount of computations in comparison with the maximum likelihood (ML) estimator. The performance of the algorithms is evaluated by Monte-Carlo simulations, and is compared with the Cramer Rao Bound (CRB). Although both techniques were successful for wideband array processing with time-invariant arrays, we found that only the interpolated array algorithm is useful for direction finding (DF) with time-varying arrays     

一种基于角度-多普勒补偿的均匀圆形

采用均匀圆形相控阵天线的机载雷达杂波分布随距离变化而变化,各距离单元的杂波不再满足独立同分布的条件,造成统计型空时自适应处理(STAP)器性能下降。基于此,本文建立了均匀圆形天线机载雷达模型,对其杂波分布进行了分析,得出了空间角随阵元数非线性变化的特性造成其杂波距离维分布非均匀的结论。研究了一种均匀圆形天线机载雷达杂波抑制方法,该方法先通过修正的角度-多普勒补偿(MADC)预处理消除在杂波谱中心处的非均匀,再利用基于导数更新(DBU)技术进一步减小在其他方位杂波的非均匀程度。仿真结果表明了该方法的有效性。     

Robust space-time adaptive processing for airborne radar in nonhomogeneous clutter environments

Space-time adaptive processing (STAP) holds tremendous potential for the new generation airborne surveillance radar, in which the phased array antennas and pulse Doppler processing mode are adopted. A new STAP approach using the multiple-beam and multiple Doppler channels is presented here for airborne phased array radar. The approach with space-time multiple-beam (STMB) architecture is robust to array errors and has very low system degrees of freedom (DOFs). Hence, it has low sample support requirement and it is very suitable for the practical planar phased array radar under nonhomogeneous clutter environments. Meanwhile, a new nonhomogeneous detector (NHD) based on the correlation dimension (CD) is also proposed here, which is used as an effective method to screen tracing data prior to detection processing. It can further improve the performance of the STAP approach in the severely nonhomogeneous clutter environments. Therefore, a scheme that incorporates the correlation dimension nonhomogeneity detector (CD-NHD) with the STMB is recommended, which we term CD-NHD-STMB. The experimental simulation results indicate that: 1) the STMB processor is robust to array element error and has high performance under nonhomogeneous clutter environments; 2) the CD-NHD is also effective on the nonhomogeneous clutter. As a result, the CD-NHD-STMB scheme is robust to array element error and nonhomogeneous clutter, and therefore available for airborne phased array radar applications.     

Nonuniform Three-dimensional Configuration Distributed SAR Signal Reconstruction Clutter Suppression

This paper deals with the problem of clutter suppression in spaceborne distributed synthetic aperture radar (D-SAR) with nonuniform three-dimensional (3D) configuration geometry. In order to make a breakthrough of the configuration limitation of the traditional space time adaptive processing (STAP) based on uniform array and improve the inhomogeneous clutter suppression performance, this paper considers signal reconstruction technique using array interpolation to process the D-SAR signal. An array interpolation signal reconstruction method based on pitching-partition is derived then a signal reconstruction 3D-STAP clutter suppression method applied to nonuniform 3D configuration is proposed. In particular, the proposed method is compared with conventional methods and the performance analysis is carried out based on simulations. The improvement factor (IF) for clutter suppression is imported and reported as a benchmark on the clutter suppression effect.     

Comparison between monostatic and bistatic antenna configurationsfor STAP

The unique characteristics of bistatic radar operation on the performance of airborne/spaceborne moving target indicator (MTI) radars that use space-time adaptive processing (STAP) are discussed. It has been shown that monostatic STAP radar has the following properties. 1) For a horizontal flight path and a planar Earth the curves of constant clutter Doppler (isodops) are hyperbolas. 2) For a sidelooking antenna geometry the clutter Doppler is range independent. 3) Clutter trajectories in the cosφ-F plane (F=normalized Doppler) are in general ellipses (or straight lines for a sidelooking array). We demonstrate that these well-known properties are distorted by the displacement between transmitter and receiver in a bistatic configuration. It is shown that even for the sidelooking array geometry the clutter Doppler is range-dependent which requires adaptation of the STAP processor for each individual range gate. Conclusions for the design of STAP processors are drawn     

Real-Time STAP demonstration on an embedded high performancecomputer

Real-time signal processing for a 16-channel phased array radar, including space-time adaptive processing (STAP) algorithms, has been implemented using a 29-node ruggedized version of an Intel Paragon. Techniques employed to efficiently implement each step of the signal processing are discussed. An overall throughput of 3.15 GFLOPS and processing efficiency of 48% has been achieved, indicating that embedded high performance computers can deliver a significant percentage of their advertised peak throughput under real system constraints     

Effects of mutual coupling on the performance of STAP antennaarrays

The effect of mutual coupling on the performance of space-time adaptive processing (STAP) antenna arrays is investigated. A signal model that includes the effects of mutual coupling is derived and used to compute the optimum solution for the fully adaptive and a variety of partially adaptive algorithms. The simulations indicate that if the mutual coupling is not properly accounted for there is significant degradation of the signal-to-interference-plus-noise ratio (SINR). In addition, the clutter notch is widened resulting in a larger minimum detectable velocity (MDV) of the target. When the mutual coupling is properly accounted for, the performance can be restored to the ideal level. However, STAP algorithms, in general, are very sensitive to errors in the mutual coupling matrix, requiring a very complete knowledge of this matrix for good performance. Of all the algorithms considered here, beam space algorithms appear to be the most robust with respect to uncertainties in the mutual coupling matrix     

Airborne/spacebased radar STAP using a structured covariance matrix

It is shown that partial information about the airborne/spacebased (A/S) clutter covariance matrix (CCM) can be used effectively to significantly enhance the convergence performance of a block-processed space/time adaptive processor (STAP) in a clutter and jamming environment. The partial knowledge of the CCM is based upon the simplified general clutter model (GCM) which has been developed by the airborne radar community. A priori knowledge of parameters which should be readily measurable (but not necessarily accurate) by the radar platform associated with this model is assumed. The GCM generates an assumed CCM. The assumed CCM along with exact knowledge of the thermal noise covariance matrix is used to form a maximum likelihood estimate (MLE) of the unknown interference covariance matrix which is used by the STAP. The new algorithm that employs the a priori clutter and thermal noise covariance information is evaluated using two clutter models: 1) a mismatched GCM, and 2) the high-fidelity Research Laboratory STAP clutter model. For both clutter models, the new algorithm performed significantly better (i.e., converged faster) than the sample matrix inversion (SMI) and fast maximum likelihood (FML) STAP algorithms, the latter of which uses only information about the thermal noise covariance matrix.     

Angle/Doppler estimation in heavy-tailed clutter backgrounds

This work describes new methods on the modeling of the amplitude statistics of airborne radar clutter by means of alpha-stable distributions. We develop joint target angle and Doppler, maximum likelihood-based estimation techniques from radar measurements retrieved in the presence of impulsive uncorrelated noise modeled as an alpha-stable random process. We derive the Cramer-Rao bounds (CRBs) for the additive Cauchy interference scenario to assess the best case estimation accuracy which can be achieved. In addition, we introduce a new joint spatial- and Doppler-frequency high-resolution estimation technique based on the fractional lower order statistics of the measurements of a radar array. Simulation results demonstrate that the proposed methods can be of interest in the study of space-time adaptive processing (STAP) for airborne pulse Doppler radar arrays operating in impulsive interference environments     

一种基于协方差矩阵加权的阵元误差补偿STAP处理

机载多通道阵列雷达天线在工程实践中不可避免地存在各类阵元误差,所产生的通道失配问题会对空时二维自适应处理的性能造成大的影响。对存在阵元误差时的阵列信号模型进行了分析,提出了一种基于协方差矩阵加权（CMT）的阵元误差补偿空时自适应处理（STAP）方法,在工程应用中该加权矩阵可通过地面天线定标及校飞过程确定,通过对总干扰协方差矩阵估计的加权预处理,可将实际阵元误差对STAP性能的影响控制在测量误差的影响范围,最后通过仿真验证了算法的有效性。     

Space-time adaptive processing and adaptive arrays: specialcollection of papers

Space-time adaptive processing (STAP) and related adaptive array techniques hold tremendous potential for improving sensor performance by exploiting signal diversity. Such methods have important application in radar, sonar, and communication systems. Recent advances in digital signal processing technology now provide the computational means to field STAP-based systems. The objective of this special collection of papers is to examine the current state-of-the art in STAP technology and explore the remaining obstacles, practical issues and novel techniques required to implement STAP-based radar, sonar or communication systems     

Importance sampling for characterizing STAP detectors

This paper describes the development of adaptive importance sampling (IS) techniques for estimating false alarm probabilities of detectors that use space-time adaptive processing (STAP) algorithms. Fast simulation using IS methods has been notably successful in the study of conventional constant false alarm rate (CFAR) radar detectors, and in several other applications. The principal objectives here are to examine the viability of using these methods for STAP detectors, develop them into powerful analysis and design algorithms and, in the long term, use them for synthesizing novel detection structures. The adaptive matched filter (AMF) detector has been analyzed successfully using fast simulation. Of two biasing methods considered, one is implemented and shown to yield good results. The important problem of detector threshold determination is also addressed, with matching outcome. As an illustration of the power of these methods, two variants of the square-law AMF detector that are thought to be robust under heterogeneous clutter conditions have also been successfully investigated. These are the envelope-law and geometric-mean STAP detectors. Their CFAR property is established and performance evaluated. It turns out the variants have detection performances better than those of the AMF detector for training data contaminated by interferers. In summary, the work reported here paves the way for development of advanced estimation techniques that can facilitate design of powerful and robust detection algorithms     

Analysis of Min-Norm and MUSIC with arbitrary array geometry

A nonasymptotic performance comparison is presented between the Min-Norm and MUSIC algorithms for estimating the directions of arrival of narrowband plane waves impinging on an array of sensors. The analysis is based on a finite amount of sensor data. The analysis makes the assumption of high signal-to-noise ratio (SNR), and it applies to arrays of arbitrary geometry. It is shown that Min-Norm can be expressed as a certain data-dependent weighted MUSIC algorithm, and that this relationship allows a unified performance comparison. It is also shown that the variances of the estimated directions-of-arrival from the MUSIC algorithm are always smaller than those of the Min-Norm algorithm at high SNR when both algorithms employ a numerical search procedure to obtain the estimates