Robust SVA method for every sampling rate condition

Linear apodization, or data weighting, is the traditional procedure to improve sidelobe levels in a finite sampled signal at the expense of resolution. New apodization methods, such as spatially variant apodization (SVA), apply nonlinear filtering to the signal in order to completely remove sidelobes without any loss of resolution. However, the results are strongly influenced by signal sampling rate. Some variations which improve results have been previously published, but sidelobe cancellation gets worse since sampling frequency is not settled at Nyquist (or a multiple). This paper presents a new and efficient technique based on SVA that drastically reduces sidelobe levels for every sampling rate condition. The algorithm is, essentially, a parameter optimization of a variant filter for each pixel of the image. A one-dimensional case and a two-dimensional generalization are presented, as well as some applications to target detection capability in a synthetic aperture radar (SAR) system.     

Improved Range Resolution Filters for Rectangular-Pulse Radar Systems

The performance of several new clutter-reduction filters suitable for rectangular-pulse radar systems is investigated. The new filters consist of various approximations and modifications of two filters known to be optimal for certain criteria: the well-known Urkowitz filter which optiizes the clutter improvement ratio, and the newer sidelobe reduction filter which minimizes output noise power subject to peak sidelobe constaints. The new filters are compared usig five basic criteria: clutter improvement ratio, signal-to-noise ratio, sidelobe peak ratio, pulse compression ratio, and filter complexity. The results are summarized in tabular and graphical form.     

一种基于数字综合算法的MTD滤波器设计方法

利用空间阵列方向图合成中的数字综合算法 ,提出了一种新的MTD滤波器设计方法。该方法通过在滤波器频率响应的副瓣区放置大量的干扰信号 ,改变干扰信号的功率强度 ,从而自适应地控制滤波器频率响应的副瓣电平。这种方法所设计的MTD滤波器 ,其频率响应不仅在零频附近有宽而深的零陷 ,而且在其他副瓣区域可以为任意形状 ,具有较好的实用性。设计实例证实了这种方法的有效性。     

Controlled Alteration of Wideband Radar Oata

A procedure is described for obtaining weights for a transversal filter which will degrade the range resolution and alter the sidelobe levels of the sampled version of a time envelope whose spectrum is band. limited and known. The two general cases of super-and sub-Nyquist rate sampling are discussed.     

A new algorithm to optimize Barker code sidelobe suppressionfilters

The authors suggest a new algorithm for binary coding waveform sidelobe reduction after matched filtering and present a general method by which optimized sidelobe suppression filters for Barker codes can be obtained with a peak output sidelobe 2.62 dB lower than the results found in the literature (for 13-b Barker code). This optimization algorithm is also promising for other binary coding waveforms, such as truncated pseudonoise (PN) sequences and concatenated codes. This new approach can readily be applied to sidelobe-reduction filter design for other binary coding waveforms, such as truncated PN sequences, concatenated codes, etc., which often find their applications in radar systems and spread spectrum communication systems     

Sequence design for IIR inverse filter pulse compression

An infinite impulse response (IIR) inverse filter structure is presented, and compared with the performance of two finite impulse response (FIR) designs. The IIR design is shown to provide better performance and be able to improve further (e.g., -1.4 dB in sidelobe levels per unit delay increase for the length-13 Barker sequence) by increasing delay. The performance parameters of this IIR inverse filter suggest a design criterion for sequences on which the filter operates; that is related to the roots of the Z transform polynomial of the sequence. The sidelobe-optimal sequence derived according to this criterion is shown to provide sharper sidelobe reduction (-6 dB per unit delay increase for the sidelobe optimal length-13 sequence)     

Coherent Doppler tomography-a technique for narrow band SAR

Some concerns regarding a technique of narrowband synthetic aperture radar (N-SAR) imaging called coherent Doppler tomography (CDT), which may be a good candidate for spaceborne applications, are addressed. Using a single-frequency signal, are addressed. Using a single-frequency signal, resolution of two tenths of a wavelength can be achieved in the point spread function if the radar platform circles the ground path to be imaged. However, the high sidelobe level of -8-dB in the point spread function results in an unacceptable dynamic range. To reduce the sidelobe level, two approaches are presented: coherent processing using multiple discrete frequencies and noncoherent subaperture processing. Simulation results demonstrate that the sidelobe level is substantially reduced by both methods. However, the resolution is degraded and the computational overhead is greatly increased for noncoherent subaperture processing. Also presented is a possible satellite geometry configuration that could utilize N-SAR processing to provide high-resolution global mapping capability     

大多普勒容限巴克码脉压

 本文介绍用补偿式非相干型旁瓣抑制滤波器(SSF)实现13位巴克码脉冲压缩旁瓣抑制的理论计算及实验结果。补偿式非相干型SSF采用最小二乘近似逆滤波方法设计,若子脉冲宽度为0.7μs,峰值旁瓣电平不超过-30dB,这种SSF的多普勒容限能达到-40kHz～+40kHz。理论计算及实验结果都表明,所设计的补偿式非相干型SSF的多普勒容限比具有同样长度冲激响应序列的R-G-ISSF有显著改善。     

Generalized Response of a Linear FM Pulse Compression Matched Filter

A pulse compression matched filter is analyzed so that the response may be computed when the pulse width, FM rate, and center frequency simultaneously differ from design conditions. Unilateral and bilateral time domain amplitude weighting for sidelobe reduction is included. A general cross-ambiguity function is defined to include these effects and some basic computed results are presented for the peak envelope response with various degrees of Hamming weighting. Computer evaluation of this cross-ambiguity function allows one to choose a combination of mismatches for signal design trade-off between resolution and detection performance. Since no restrictions are placed upon the mismatch parameters, this analysis may also be used to evaluate the filter discrimination against various interfering signals.     

Adaptive resolution of mainlobe and sidelobe detections using model order determination

This work presents the development and performance evaluation of a methodology for distinguishing between mainlobe and sidelobe detections that arise in adaptive radar systems operating in adverse environments. Various adaptive detection test statistics such as the adaptive matched filter (AMF), the generalized likelihood ratio test (GLRT), and adaptive coherence estimate (ACE), and combinations of these, have been previously analyzed with respect to their sidelobe rejection capabilities. In contrast to these methods which are based on detecting a single target with known direction and Doppler, the present method uses model order determination techniques applied to the AMF or GLRT data observed over the range of unknown angle and Doppler parameters. The determination of model order, i.e., the number of signals present in the data, is made by using least-squares model fit error residuals and applying the Akaike Information Criterion (AIC). Comprehensive computer simulation results are presented which demonstrate substantial improvement in sidelobe rejection performance and detections of multiple sources compared with previous methods.     

Clutter Suppression by Complex Weighting of Coherent Pulse Trains

Uniform coherent pulse trains offer a practical solution to the problem of designing a radar signal possessing both high range and range-rate resolution. The Doppler sensitivity provides some rejection of off-Doppler (clutter) returns in the matched filter receiver. This paper considers the use of a processor in which members of the received pulse train are selectively weighted in amplitude and phase to improve clutter suppression. The techniques described are particularly suitable for rejecting interference entering the processor through ambiguous responses (range sidelobes) of the signal. The complex weights which are derived are optimum in the sense that they produce the maximum clutter suppression for a given detection efficiency. In determining these weights, it is assumed that the distribution of clutter in range and range rate relative to targets of interest is known. Thus, clutter suppression is achieved by reducing the sidelobe levels in specified regions of the receiver response. These techniques are directly applicable to array antennas; the analogous antenna problem would be to reduce sidelobe levels in a particular sector while preserving gain. Complex weighting is most successful when the clutter is limited in both range and velocity.     

A multiobjective optimization approach to determine the parameters of stepped frequency pulse train

Frequency stepping techniques are commonly used in modern radar system to get high range resolution with the disadvantage that its autocorrelation function (ACF) yield undesirable “grating lobes”. Wider mainlobe deteriorates the range resolution capability of the waveform and higher peak sidelobe either hides the small targets or causes the false target detection. Several techniques have been used to choose the parameters of linear frequency modulated (LFM) pulse train to suppress the grating lobes without paying much attention to the mainlobe width and peak sidelobe level. In this paper a multiobjective optimization (Nondominated Sorting Genetic Algorithm-II (NSGA-II)) approach is proposed to optimize the parameters of the LFM pulse train to achieve reduced grating lobes, low peak sidelobe level and narrow mainlobe width. The optimization problem has been studied in two different ways: first one is associated with the reduction of grating lobes and the minimization of peak sidelobe level of the ACF with constraints and second one is related to the minimization of the peak sidelobe level and mainlobe width of the ACF with constraints. Simulation studies have been carried out to justify the potentiality of the proposed approach.     

Comments on "Computationally Efficient Bank of Rectangular Digital Filters"

In [1] a scheme for forming a rectangular FIR filter bank is described using only a few percent of the number of multiplications required by straightforward procedures. The sidelobe level suffers degradation. Attention is drawn to a different scheme published in [2] and [3] which needs even fewer multiplications without degradationvof the sidelobe level.     

Range sidelobe reduction for the quadriphase codes

Filters that reduce the sidelobes of the quadriphase-coded waveform are realized by applying the biphase-to-quadriphase transformation to the filter designs that reduce the sidelobes of the prototype biphase code. The mismatch loss is invariant under this transformation, but the resulting peak-to-sidelobe ratio (PSR) can decrease 1.5 dB maximum. An example illustrates the procedure for a compressor composed of a sidelobe reducing filter cascaded with the matched filter and a compressor realized as one mismatched filter     

A chirp scaling approach for processing squint mode SAR data

Image formation from squint mode synthetic aperture radar (SAR) is limited by image degradations caused by neglecting the range-variant filtering required by secondary range compression (SRC). Introduced here is a nonlinear FM chirp scaling, an extension of the chirp scaling algorithm, as an efficient and accurate approach to range variant SRC. Two methods of implementing the approach are described. The nonlinear FM filtering method is more accurate but adds a filtering step to the chirp scaling algorithm, although the extra computation is less than that of a time domain residual compression filter. The nonlinear FM pulse method consists of changing the phase modulation of the transmitted pulse, thus avoiding an increase in computation. Simulations show both methods significantly improve resolution width and sidelobe level, compared with existing SAR processors for squint angles above 10 deg for L-band and 20 deg for C-band     

Nonlinear apodization for sidelobe control in SAR imagery

Synthetic aperture radar (SAR) imagery often requires sidelobe control, or apodization, via weighting of the frequency domain aperture. This is of particular importance when imaging scenes containing objects such as ships or buildings having very large radar cross sections. Sidelobe improvement using spectral weighting is invariably at the expense of mainlobe resolution presented here is a class of nonlinear operators which significantly reduce sidelobe levels without degrading mainlobe resolution implementation is via sequential nonlinear operations applied to complex-valued (undetected) SAR imagery. SAR imaging is used to motivate the concepts developed in this work. However, these nonlinear apodization techniques have potentially broad and far-ranging applications in antenna design, sonar, digital filtering etc., i.e., whenever data can be represented as the Fourier transform of a finite-aperture signal     

Optimum Mismatched Filters for Sidelobe Suppression

This paper discusses the application of least-mean-squares approximate inverse filtering techniques to radar range sidelobe reduction. The method is illustrated by application to the 13-element Barker code. The performance of the least-mean-square inverse filter is compared with the matched filter and with the simplified sidelobereducing filters of Rihaczek and Golden. A filter which completely suppresses the range sidelobes of a 13-element Barker sequence is only 0.2 dB worse than a matched filter in noise.     

A new CFAR sidelobe canceler algorithm for radar

Signal or target detection is sometimes complicated by the presence of strong interference. When this interference occurs mainly in the sidelobes of the antenna pattern, a solution to this problem is realized through a sidelobe canceler (SLC) implementation. Since the false-alarm probability is a system parameter of special importance in radar, an interference-canceling technique for radar application should maintain the false-alarm probability constant over a wide range of incident interference power. With the requirements of sidelobe interference cancellation and constant false alarm rate (CFAR), a new algorithm for radar detection in the presence of sidelobe interference is developed from the generalized likelihood ratio test of Neyman-Pearson. In this development, the received interference is modeled as a nonstationary but slowly varying Gaussian random process. Cancellation of the sidelobe interference is based upon a `synchronous' estimate of the spatial covariance of the interference for the range gate being tested. This algorithm provides a fixed false-alarm rate and a fixed threshold which depend only upon the parameters of the algorithm     

Poly-phase codes and optimal filters for multiple user ranging

A technique is introduced to select poly-phase codes and optimal filters of a pulse compression system that have specific temporal and frequency characteristics. In the particular problem under study, multiple vehicles are assigned unique codes and receiver filters that have nearly orthogonal signatures. Narrowband users, that act as interference, are also present within the system. A code selection algorithm is used to select codes which have low autocorrelation sidelobes and low cross correlation peaks. Optimal mismatched filters are designed for these codes which minimize the peak values in the autocorrelation and the cross correlation functions. An adjustment to the filter design technique produces filters with nulls in their frequency response, in addition to having low correlation peaks. The method produces good codes and filters for a four-user system with length 34 four-phase codes. There is considerable improvement in cross and autocorrelation sidelobe levels over the matched filter case with only a slight decrease in the signal-to-noise ratio (SNR) of the system. The mismatched filter design also allows the design of frequency nulls at any frequency with arbitrary null attenuation, null width, and sidelobe level, at the cost of a slight decrease in processing gain     

11位巴克码的LP滤波器及其在多普勒频移下的性能

本文介绍使最大旁瓣值最小的11位巴克码滤波器（LP滤波器）的计算结果。并介绍多普勒频移对这种滤波器性能影响。LP滤波器长度为53时,旁瓣电平降到—39.5dB,比匹配滤波器改善18.7dB。对加权序列长度L为41、45、49和53的11位巴克码的LP滤波器计算结果表明,其性能受多普勒频移的影响表现为:它们的主瓣电平下降、主瓣展宽、最小旁瓣电平上升、旁瓣电平平方和上升和信噪比损失增大。在较小的多普勒频移（f_d）时,L大的LP滤波器其性能优于L小的LP滤波器,在多普勒频移交大时,这种优势逐渐消失,不同长度LP滤波器性能大体一致。