飞机反推系统"储压器压力低灯亮"故障分析

全面分析和总结了MD-82飞机反推系统的工作原理,给出了MD-82空中“反推储压器压力低灯亮”这一典型故障的排故思路,对反推系统其他故障及其他机型的反推系统排故均有一定的借鉴意义。     

民用飞机反推力格栅出流模式设计与试验

通过给定各块格栅上气流的折流角,反推力格栅出流模式描述了反推气流方向沿发房周向的分布。出流模式的定义需要考虑使反推系统满足反推效率,重吸入特性和有效面积方面的要求,还应使反推气流对机体气动特性的影响最小化。格栅出流模式设计是否满足反推效率和有效面积的要求,可由单独反推系统的静态试验来进行验证,而重吸入特性和发动机/飞机气动干扰则必须通过全机反推力风洞试验来进行考察。     

空客A330反推装置典型故障分析

通过对历年空客A330飞机反推系统故障统计,确定了反推系统的典型故障,并详细介绍了典型故障的排故思路和经验总结．列出了一些重点注意事项。     

B737NG飞机反推系统故障分析

根据波音的相关技术文件,B737NG反推系统的部件有些本身带有设计缺陷或可靠性较低,导致反推系统故障较多。对反推系统的工作原理、常见故障及处理方法进行总结,使排故人员和故障管控工程师对该系统有深入的了解,方便大家开阔思路,减少排故的时间,提高排故效率。     

浅析一起线路磨损导致的CFM56-5B反推故障

针对一起空客A320飞机因吊架处隔离活门导线束磨损导致左发反推无法放出故障,从反推系统工作原理入手,结合系统线路图进行了分析,给出了排除此类故障的最佳切入点,对排故流程进行了优化。     

反推装置对翼身融合分布式推进系统气动性能影响数值模拟

为了研究新型反推装置对翼身融合分布式推进系统气动性能的影响,将机身简化为二维模型,利用数值模拟的手段来研究攻角、反推开度,以及风扇打开或关闭对飞行参数的影响,为翼身融合分布式推进系统的反推装置设计提供初步的意见和建议。结果显示:反推闭合和风扇打开之后该机型的升力系数和俯仰力矩系数都会有较大增加;随着反推开度的增加,升力系数和俯仰力矩系数也随之增加;来流攻角对翼身融合分布式推进系统的气动性能也有较大影响。      

波音737NG飞机反推展出故障代码S833/S830浅析

波音737NG飞机反推系统的故障率较高,FIM手册中的排故说明虽然很全面,但也有一些特例.本文结合FIM手册和反推工作原理,分析了波音737NG飞机反推展出代码S833(左发)或S830(右发)的故障原因,并给出了排故的补充建议.     

CFM56-7B发动机反推损伤及原因分析

反推作为飞机发动机的一部分在降落时起到减速的作用,对缩短降落距离有着显著的效果,反推损伤将对飞行性能和飞行安全造成一定的影响,了解反推系统的原理、构造和常见的损伤及其原因非常重要.本文结合波音公司相关技术文件与实际工作经验,总结反推常见损伤并分析反推损伤产生的原因,便于工作者在实际工作中重点检查常见损伤部位,快速找到损...     

某型反推力装置室内试车台试验方法

反推力装置是大涵道比涡扇发动机的重要组成部件。对反推装置研制过程中的室内试车试验方法进行了总结,介绍了所用反推力装置结构、试车台反推力装置控制系统,阐述了反推涡壳装置的设计与安装使用方法,探讨了反推力测量系统,总结了反推装置静态与全状态的调试方法。试验结果表明:采用的试验方法可有效指导室内反推力装置试验,获得了发动机在不同反推力状态下的性能数据,对反推装置的室内试车试验方法的建立具有一定的参考价值。     

波音737NG飞机反推排故与维护

主要以波音737NG飞机为例,利用飞机维护手册(AMM)和故障隔离手册(FIM)清晰阐述了波音737NG飞机反推控制原理,结合反推系统常见故障现象及可能的故障原因,创新运用故障树理论,建立起一套针对不同故障现象的快速甄别、判断、排除方法。该文对民航维修人员掌握反推系统原理、准确判断故障、保障飞机顺利运行具有重要意义;同时,有助于民用飞机设计、制造以及维修方案的制定。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.