CIECA: Application to Current Programmed Switching Dc-Dc Converters

Sundstrand Advanced Technology Corporation The current injection equivalent circuit approach (CIECA) to modeling switching converter power stages is extended to model the current programmed converter power stages operating in fixed frequency, continuous inductor conduction mode. To demonstrate the method, modeling is carried out for the buck, boost, and buckboost converters to obtain small-signal linear equivalent circuit models which represent both input and output properties. The results of these analyses are presented in the form of linear equivalent circuit models as well as transfer functions. Though current programmed converters exhibit single-pole response, the addition of artificial ramp changes converters to exhibit well damped two-pole response. This has been investigated for the first time using CIECA. The results of these analyses are presented in the form of linear equivalent circuit models as well as transfer functions.     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Design Optimization for a Half-Bridge DC-DC Converter

A nonlinear programming technique using the penalty function method is employed for the minimum weight design of a halfbridge dc-dc buck power converter. The cost-effective computeraided approach provides a minimum weight design down to the details of the component level which concurrently meets all power circuit performance requirements. Important design insights and guidelines are obtained to readily assess 1) the tradeoffs between weight and loss as the switching frequency is increased, 2) the optimum operating frequency range over which the total weight/loss is minimized, 3) the impact of device characteristics on the total weight and loss profile.     

Novel AC-DC and DC-DC converters with a diode-capacitor multiplier

This paper presents a transformerless ac-dc and or dc-dc converter with a high output voltage multiplicity, which contains only one switch. The converter consists of an inverter and a diode-capacitor multiplier (DCM) and provides a voltage gain equal to double the number of multiplier steps. In the case of ac-dc conversion the proposed converter offers a practically unit power factor and provides a sine wave input current. The analysis of the steady state as well as the transient behavior of the DCM is given and simplified equivalent circuits are proposed. The prototype of the DCM has been built and tested to show the validity of the proposed converter. The theoretical analysis, the computer simulation results, and the experimental testing results are in good agreement.     

Improved Switching Converter Model Using Discrete and Averaging Techniques

The nonlinear modeling and analysis of dc-dc converters has been done by averaging and discrete-sampling techniques. The averaging technique is simple, but inaccurate, as the modulation frequencies approach the theoretical limit of one-half the switching frequency. The discrete technique is accurate even at high frequencies, but is very complex and cumbersome. An improved model is developed by combining the aforementioned techniques. This new model is easy to implement in circuit and state variable forms and is accurate to the theoretical limit.     

Stability analysis of parallel DC-DC converters

We develop analytic methodologies for stability analyses (using nonlinear and linear methodologies) of parallel dc-dc converters (under unsaturated and saturated operating conditions) using their switching model, discrete model (based on nonlinear map), and averaged model. We describe the approach for investigating the behavior of the stable and unstable equilibrium solutions of a parallel dc-dc converter under parametric variations and illustrate the methodology using a load-sharing dc-dc buck converter. For unsaturated operating condition, using bifurcation analysis and Floquet theory, we predict the stability boundary of the nominal solution, determine its postinstability dynamics, and investigate the dependence of the converter dynamics on its initial conditions. Subsequently, we demonstrate the differences in the predictions of the instabilities and instability boundaries using (conventional) linearized averaged (small-signal) and discrete and switching models.     

Current-fed multiresonant isolated DC-DC converter

A novel topology, current-fed multiresonant dc-dc converter (CF-MRC) was studied theoretically and experimentally. The new topology differs from previously described current-fed push-pull parallel-resonant topologies in the fact that the output is coupled to the current of the resonant inductor and in the addition of a second capacitor across the transformer. The main features of the proposed converter are an inherent protection against a short and open circuit at the output, a high voltage gain and zero voltage switching (ZVS) over a large range of output voltage. These characteristics make it a viable choice for applications, such as a high voltage capacitor charger, that require controllable current sourcing over a wide output voltage swing.     

Single-Stage Single-Switch Switched-Capacitor Buck/Buck-Boost-Type Converter

A new dc-dc converter featuring a steep step-down of the input voltage is presented. It answers a typical need for on-board aeronautics modern power architectures: power supplies with a large conversion ratio able to deliver an output voltage of 1–1.2 V. The proposed structure is derived from a switched-capacitor circuit integrated with a buck converter; they share the same active switch. The proposed solution removes the electromagnetic interference (EMI) emission due to the large di/dt in the input current of the switched-capacitor power supplies. Compared with a quadratic buck converter, it presents a similar complexity, a smaller reduction in the line voltage at full load (but less conduction losses due to smaller input inductor current and capacitor voltage), lower voltage stresses on the transistor and diodes, lower current stresses in the diodes, and smaller size inductors. A similar structure using a buck-boost converter as the second stage is also presented. The experimental results confirm the theoretical developments.     

An efficient active ripple filter for use in DC-DC conversion

When low ripple is required from a switched mode dc-dc converter, dissipative active filters offer an alternative to passive LC and coupled inductor filters. Analytical and experimental results are presented for a simple active ripple filter. The filter employs a pair of current transformers as sensors for feedforward and feedback control and two metal-oxide-semiconductor field-effect transistors (MOSFETs) as cancellation current drivers. Measurements demonstrate good ripple attenuation up to 5 MHz, more than 70 dB being obtained at 100 kHz, the switching frequency of a test converter. The overall efficiency was measured as 95%, with room for further improvement. The filter is suitable for input and output smoothing in dc-dc converters for aerospace and other critical applications     

并联H桥DC/DC变换器软开关技术研究

与传统的Buck电路相比,基于H桥并联的DC/DC变换器可以实现电压的双极性输出和故障时的冗余控制,非常适合用于大功率电动机正反转控制的场合。分析了并联H桥型DC/DC变换器的结构组成和双脉宽调制(PWM)模式。为了降低双脉宽调制下H桥型DC/DC变换器的开通和关断损耗,对无源软开关技术进行了分析,重点探讨了RCD缓冲电路和最小应力缓冲电路之间的性能差异,指出最小应力软开关技术可以获得更好的软开关性能,并就将其用于双脉宽调制下的并联H桥DC/DC变换器进行了仿真研究。仿真结果表明:最小应力软开关技术用于双脉宽调制下并联H桥DC/DC变换器时,可以实现开关管的零电压开通和零电流关断。     

General rules for signal flow graph modeling and analysis of dc-dc converters

Signal flow graph (SFG) nonlinear modeling approach is well known for modeling dc-dc converters. However, all possible SFGs of a given dc-dc converter system will not yield the generalized graph. A systematic procedure and guidelines for developing unified flow graph models of the dc-dc boost converters, from which complete behavior can be determined is presented. Usefulness of the proposed method is demonstrated through examples. As an illustration a 2-cell cascade boost and interleaved boost converter systems are taken as examples. Derivation of large, small-signal and steady-state models from generalized flow graph is also demonstrated. Large-signal model is developed and programmed in TUTSIM simulator. Large-signal, responses against supply and load disturbances are obtained. Experimental observations are provided to validate the proposed algorithm.     

Modeling of a new ZVS bi-directional dc-dc converter

A dual half-bridge (DHB) bidirectional dc-dc converter is a new proposed topology that has the advantages of decreased number of devices, soft-switching implementation, low cost, and high efficiency. Typical applications of this converter are the auxiliary power supply in fuel cell vehicles and battery charging and discharging systems where the power density, cost, weight, and reliability are critical factors. A switching-frequency-dependent state-space averaged model of the converter is developed here for either direction of power flow. This averaged model can be used to derive the steady-state characteristics and small signal dynamics of the proposed topology. It also provides a fast simulation tool to investigate the transient response of the converter. The simulated waveforms of the mathematical model are compared with the detailed circuit simulation to verify the accuracy of the modeling.     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

New ZVT-PWM DC/DC converters using active snubber

A novel active snubber soft switching method is proposed. The unique location of the resonant inductor and capacitor ensures low current and voltage stresses in the converter. An analytical study of a boost dc-dc converter with the proposed active snubber method is presented in detail to illustrate its operation principles and design considerations. By simple modification, this soft switching method is also suitable for ac-dc boost topology, especially for high power-factor-correction (PFC) universal interface applications. A 500 W prototype system has been made to simulatively and experimentally verify the performance of the soft switching.     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

Tolerance design of controllers for switching regulators

An evolutionary approach to worst case tolerance design is introduced here, with a focus on feedback compensation networks for dc-dc switching converters. Assumed that varying parameters values are uniformly distributed and uncorrelated, as provided by the worst case approach, the proposed algorithm, of general applicability, seeks for the set of nominal values and tolerances of the circuit parameters ensuring that the design constraints are met and that a user-defined circuit performance index assumes its optimal value. Design constraints, are fixed in the frequency domain, in terms of acceptability ranges of loop gain crossover frequency and phase margin, to guarantee closed loop stability and the desired dynamic performance. Resistive and capacitive compensation network's parameters values are chosen within a suitable database of couples nominal value/tolerance available on the market, while the nominal values and tolerances of the parameters of the power stage are fixed. Referring to a buck dc-dc switching regulator, two widely used different compensation network topologies are compared in terms of reliability, robustness, and cost of components. Simulation results show the wide usefulness of the proposed method in supporting designer decisions.     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

Battery charger design for the Columbus MTFF power system

A novel pulsewidth-modulated (PWM) dc-dc converter topology is proposed for the battery charge regulator (BCR) of the Columbus Man-Tended Free-Flyer (MTFF) power system. The system is a regulated bus system. Bus voltage control is implemented at the input of the BCR. The use of a conventional buck topology with PWM conductance control at the input results in a second-order behavior. A study of new PWM dc-dc converter topologies has been made to attain a suitable topology. The proposed converter topology is designed and a breadboard including the control loop has been built and tested. The experimental results show that the converter operates according to the design constraints.     

High power factor operation of DCM series-parallel resonantconverter

This work presents the operating principle, analysis, design, simulation, and experimental results for a high frequency (HF) transformer isolated single stage ac-to-dc series-parallel resonant converter (SPRC) operating on the utility line, in discontinuous current mode (DCM). The equivalent circuit models and the state space analysis of the SPRC in DCM are presented. PROMATLAB software is used to solve the equations and to obtain important design parameters. SPICE3 simulation and experimental results obtained from a 150 W prototype are presented to verify the analysis. High power factor operation (>0.99) with low harmonic distortion (<18%) have been achieved for the entire load range even without active control, in addition to eliminating switching losses     

BuckBoost变换电路DCM动态建模分析

以BuckBoost电路为例,求解了变换器的平均模型及其线性化后的小信号模型。利用Simulink软件分别搭建状态平均方程等效电路、线性化小信号模型等效电路。通过动态模型仿真与开关器件电路仿真结果对比,验证了动态模型的正确性,讨论了断续电流模式(DCM)平均模型的适用范围与存在的缺陷。理论分析结果表明:大信号和小信号模型,在宏观时间尺度上,可以较好地模拟实际开关电路的动态特性。小信号模型只能用来求解扰动较小的情况,即当扰动过大时,小信号模型求解的误差将会很大。