基于数值定容弹方法的推力室阻尼特性研究

为确定推力室的声学振型频率及其阻尼特性,给出推力室最容易激发声学振型和最难衰减声学振型,建立了基于数值定容弹和半带宽法的推力室声学振型及其阻尼特性的数值模拟方法。对小推力姿轨控发动机推力室进行近圆周壁面的定容弹激励仿真,激发出了多模态的声学振型,其中,一阶切向振型为最容易激发振型,而一阶纵向振型为最难衰减振型。进一步讨论了推力室构型参数对其阻尼特性的影响,结果表明:随推力室内径增大,纵向振型得到抑制,而切向振型变得不易衰减;随推力室收缩比增加,一阶切向振型半带宽先增大后保持不变;随推力室圆柱段长度增加,各振型半带宽没有明显的变化趋势。     

推力室状态对其声学振型及其阻尼特性的影响

为确定工程中冷态条件下获得的推力室声学特性能否表征真实条件下的声学特性,研究了冷态无流动、热态气相流动和湍流两相燃烧三种状态下推力室声学振型及其阻尼特性。在推力室稳态流场中的有限区域施加数值定容弹,激发其具有多模态声学振型的大幅值压力振荡,采用衰减时间和半带宽来定量评价所激发的不同声学振型压力振荡衰减快慢,进而获得其阻尼特性。在相同过载比的数值定容弹激励下,在冷态条件下能激发包含更多声学振型压力振荡,且该振荡衰减时间更长,相同振型压力振荡衰减比热态条件下慢。在冷态条件下,一阶切向振型振幅最大,为最容易被激发声学振型;一阶纵向振型半带宽最小,为最难衰减的振型。在热态条件下,一阶纵向振型为最容易激发声学振型,也为最难衰减声学振型。从所激发的主要振型及其相对衰减的快慢来看,冷态条件下获得的声学特性能够表征真实条件下的推力室的声学特征。     

基于数值定容弹方法的燃烧室声学特性研究

为确定给定构型燃烧室最容易激发的声学振型,提出了能够实现大幅值非特定频率的"数值定容弹"模型。圆柱体内声学振型频率的预测值与理论结果偏差在7%以内。对姿轨控发动机推力室进行了数值定容弹激励,给出了推力室压力分布的时空演化,获得了多声学模态压力振荡及其最容易激发的声学振型。进一步研究了收缩比对推力室声学特性的影响。结果表明:随着收缩比增大,一阶和二阶切向声学振型的幅值增加,但对应的频率基本保持不变;而一阶纵向和一切-一纵声学振型的幅值减小,但对应的频率增大,当收缩比较大时,一阶纵向和一切-一纵声学振型消失。可见,与短粗构型相比,细长推力室构型有利于抑制切向声学振型。     

有声腔推力室的声学振型及其阻尼特性研究

为确定多声学模态压力振荡条件下带有1/4波长管声腔推力室的声学振型及其阻尼特性,揭示1/4波长管声腔对推力室压力振荡的抑制作用机理,对有声腔推力室和无声腔推力室进行近圆周壁面的定容弹激励仿真,激发了多模态的声学振型,给出了推力室压力分布的时空演化,并采用半带宽法定量评价每个激发声学振型的阻尼特性。结果表明：1/4波长管声腔成功抑制了目标振型（一阶切向振型）压力振荡,大幅度减小其幅值,而不是大幅度增加其半带宽,但可能增强其它非目标振型的压力振荡。声腔通过削弱目标振型波峰波谷压力差、声腔入口漩涡和增加壁面面积等三种方式来抑制目标振型压力振荡,主要以前者为主,前者旨在降低目标振型幅值,后两者是增加其半带宽。     

有声腔燃烧室的声学特性实验

为了掌握声腔对燃烧室声学特性的影响规律,采用冷态实验方法,研究了带有轴向直圆孔声腔的模拟燃烧室的声学特性,其中声腔长度、开口面积比（声腔横截面积除以燃烧室横截面积）和个数均可调节.研究结果表明:燃烧室固有频率随声腔长度的增加而逐渐减小;声腔存在最佳深度,能够抑制一阶切向振型,该最佳深度不受声腔开口面积比影响,略小于1/4一阶切向波长;对抑制一阶切向振型而言,声腔存在最佳开口面积比,在本研究中约为0.17;声腔的分布对燃烧室的声学特性影响较大,相同开口面积比下,声腔个数越多,声波衰减越快.      

气喷嘴和声腔对燃烧室声学特性的影响

为了掌握气喷嘴和声腔对燃烧室声学特性的影响规律以及解释声学实验中出现的切向频率分化现象的内在机理,采用声学有限元方法(FEM)并在单喷嘴声学模拟实验验证的基础上,从固有频率和声压分布角度分析了气喷嘴长度、声腔长度和节流嘴直径对燃烧室声学特性的影响规律,利用声压分布成功地解释了实验中出现的频率分化现象。结果表明:当燃烧室某阶切向振型频率与喷嘴1阶纵向振型频率相等时,喷嘴由于共振将切向振型声压幅值极值点附近的能量转移到喷嘴中,改变了燃烧室原切向振型的声压分布,因此在声学实验中产生切向频率分化现象;气喷嘴长度与节流嘴直径之间存在着耦合关系,在液氧煤油补燃发动机喷嘴设计阶段可进行组合参数匹配优化。      

大直径液氧煤油发动机燃烧室抗脉动隔板技术

随着发动机推力的增大,燃烧室直径也随之增大,表征燃烧室热声学特性的振型、频率及其组合振型更为复杂,燃烧室带与不带抗脉动隔板以及隔板的结构参数等对声学特性影响明显,直接影响燃烧不稳定性的裕度。为了研究抗脉动隔板结构参数对燃烧室声学特性的影响,本文基于三维柱坐标系声波动理论和COMSOL仿真平台,研究了抗脉动隔板结构对火箭发动机燃烧室声学特性的影响。通过单喷嘴声学模拟实验,验证了该仿真方法的有效性。分析了隔板高度、厚度和冷区长度对燃烧室声学特性的影响规律。研究结果表明:隔板高度由40mm增加至120mm时,燃烧室一阶切向和二阶切向振型的频率分别下降了22%和31%;隔板厚度和冷区长度对燃烧室声学频率的影响不超过5%;大推力补燃发动机燃烧室直径大,需采用结构形式更为复杂的抗脉动隔板来针对性地抑制横向振型。     

隔板对液体火箭发动机燃烧室声学模态特性的影响

通过采用声学有限元法,求解带有平均流源项的亥姆霍兹方程,进而在考虑燃烧室高温、平均流场因素基础上分析了隔板结构参数对液体火箭发动机燃烧室声学模态特性影响规律。结果表明：增加隔板数目或长度,均会降低燃烧室1阶切向模态的特征频率;存在最佳隔板数目4,使燃烧室1阶切向模态阻尼率最大;而隔板长度越长,1阶切向模态声压波腹的分布面积越小,阻尼率越大;隔板型式对燃烧室1阶切向模态特性影响较小。     

隔板对燃烧室声学特性的影响

为了研究液体火箭发动机燃烧室出现的横向一阶切向燃烧不稳定,通过冷态声学试验和理论算例的计算,研究了不同参数的隔板装置对一阶切向声学频率及阻尼特性的影响,结果表明:增加轴向隔板长度和径向隔板数目均会降低一阶切向声学频率,同时增强声阻尼效果;喷嘴式隔板产生的声阻尼效果,比典型直板形状的隔板要好得多,隔板喷嘴最佳间隙在0.1~0.4mm,采用最佳隔板喷嘴间隙能够在较短的轴向隔板长度上得到较高的阻尼能力,从而改善冷却问题.      

具有气液同轴喷嘴的液体火箭发动机燃烧室压力振荡及其声学特性研究

为探究液氧/煤油液体火箭发动机气液同轴喷嘴模型燃烧室具有良好稳定性的原因,采用非稳态雷诺平均（URANS）方法数值研究了其燃烧不稳定性和声学特征。两相燃烧条件下,燃烧室压力振荡幅值约为室压的10%左右、最大不超过25%,且以纵向和横向振型为主。一周六径隔板对横向振型具有很强的抑制作用,但对纵向振型影响较小。与液-液撞击式液氧/煤油发动机模型燃烧室相比,本文研究的燃烧室中煤油液滴没有发生超临界蒸发现象,第三邓克尔数较小,诱发燃烧不稳定性的激励源较弱。进一步通过数值定容弹激发了燃烧室多模态声学特征压力振荡,并得到了其振荡特征频率、幅值和衰减率。结果表明,气喷嘴具有四分之一波长喷嘴特征,能显著减小目标振型的幅值,而集气腔对纵向振型具有很强的抑制作用,同时对其他振型也有程度不同的抑制效果。因此,较弱的燃烧不稳定性激发机制以及隔板、气喷嘴和集气腔对纵向和横向振型很强的抑制作用,使得该液氧/煤油发动机气液同轴燃烧室具有很好的稳定性。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.