共查询到20条相似文献,搜索用时 203 毫秒
1.
研究了Zn—Ni合金不钝化镀层结合力受温度的影响,电流密度对Zn—Ni合金电镀成分的影响。得出45℃时,镀层Ni含量为13.5%,耐盐雾腐蚀时间达到最高1632小时,是较理想的高强度300M钢防护镀层,其氯化物——硫酸盐镀液为比较理想的无镉、无氰环保型镀液。 相似文献
2.
研究了制造工艺对点火器铂铑催化网管性能的影响,分析了镀层表面行貌以及电镀时间、电镀温度、电流密度、氢气活化对镀层表面形貌的影响.组织致密、颗粒大、无孔洞的试样与镀层表面颗粒小、有孔洞、疏松的试样在催化活性方面有一定差异.适当控制电流密度,控制电镀时间1~2 h,电镀温度30~40 ℃,氢气活化处理温度500~700 ℃,镀层颗粒度和镀铂增重可以控制在适当范围内. 相似文献
3.
采用双向脉冲电沉积法从Cr3+镀液中电沉积出铬镀层,并利用扫描电子显微镜(SEM)研究脉冲参数对铬镀层的微观形貌影响的规律,分析脉冲波形参数与Cr3+镀液阴极电流效率之间的相关性,就双向脉冲电沉积与直流电沉积过程中所得铬镀层的微观形貌、Cr3+镀液的阴极电流效率进行分析、比较.结果表明:平均电流密度、逆向脉冲系数、脉冲频率、以及占空比均对铬镀层的微观形貌及电流效率有较大影响;采用双向脉冲电沉积法制备出的铬镀层具有表面平整、结晶细致、粗糙度良好的特点,且具有较高的阴极电流效率. 相似文献
4.
电沉积条件对Ni-Mo合金成分及其形貌的影响 总被引:1,自引:0,他引:1
利用SEM研究了电沉积条件,如:电流密度、电镀时间、镀液温度、pH值、空气搅拌、及N2H4·H2SO4浓度等对Ni-Mo合金成分和形貌的影响。利用XRD研究了Ni-Mo合金沉积层的结构。在电流密度为6.75A/dm2,镀液温度为25℃,pH=8.3,电镀时间为10min,空气搅拌的情况下,Ni-Mo合金沉积层中Mo的含量高达68wt%。XRD结果表明其沉积层为非晶结构. 相似文献
5.
耐高温Ni—ZrO2复合镀层的制备及影响因素研究 总被引:1,自引:0,他引:1
采用复合电沉积技术制备出了Ni-ZrO2耐高温复合镀层,并利用正交设计对影响复合电沉积过程的电流密度i、镀液中微粒浓度c、搅拌方式m、微粒粒径d及其间的交互作用等进行了研究。结果表明,上述因素对复合镀层中ZrO2含量影响显著性大小顺序为:d>m>d×m>c>d×c>i×m。 相似文献
6.
7.
1 电刷镀技术本成果研究的金属电刷镀与非金属电刷镀 ,与传统的电镀技术相比 ,它无需镀槽 ,采用专用电源、镀液和镀笔 ,通过电化学结晶过程 ,使被镀工件表面获得镀层。设备简单、加工工件尺寸不受限制 ,可在现场操作 ,镀层种类多 ,镀液达 15 0多种。适应性强 ,镀层结合强度、硬度和耐磨性良好 ;工艺灵活 ,容易掌握 ;沉积速度快 (较镀槽镀快 2 0倍 ) ,省工、省料、省能源 ,投资少 ,环境污染小 ,经济效益显著。电镀层厚度为 0 .0 1mm~ 1.0 0mm ;沟槽镀层厚度 3mm ;结合强度 2 35 .2MPa(槽镀为 83.3MPa) ;表面硬度HRC60 ;耐温… 相似文献
8.
9.
10.
本文简述振动电镀的设备构造,振动的工作原理,主要镀液参数与振动频率的关系,单槽加工装载量及振动频率对镀层影响,振动电镀的特色,振动电镀的适用性和应用. 相似文献
11.
《中国航空学报》2015,(4)
Anodizing is always used as an effective surface modification method to improve the corrosion resistance and wear resistance of titanium alloy.The sodium tartrate anodizing is a new kind of environmental anodizing method.In this work, the effects of sodium tartrate anodizing on mechanical property were studied.The oxide film was performed on the TA15 titanium alloy using sodium tartrate as the film former.The effects of this anodizing and the traditional acid anodizing on the fatigue life of TA15 alloy were compared.The results show that the sodium tartrate anodizing just caused a slight increase of hydrogen content in the alloy, and had a slight effect on the fatigue life.While, the traditional acid anodizing caused a significant increase of hydrogen content in the substrate and reduced the fatigue life of the alloy significantly. 相似文献
12.
Titanium alloy plays a crucial role in the electrochemical field due to its excellent corrosion resistance. The passivation and dissolution behaviors of Ti-6.5Al-2Zr-1Mo-1V(TA15) alloy in Na Cl solution were studied by simulating the electrochemical machining process in a rotating condition, which made the anode in a state with alternating high and low current density. Electron probe micro analysis, ultra-depth microscope, scanning electron microscope, and X-ray photoelectron spectrometer were u... 相似文献
13.
《中国航空学报》2015,(4)
This study investigates the feasibility of using electrochemical machining(ECM) to produce critical aeroengine components from a new burn-resistant titanium alloy(Ti40), thereby reducing costs and improving efficiency relative to conventional mechanical machining.Through this, it is found that an aqueous mix of sodium chloride and potassium bromide provides the optimal electrolyte and that the surface quality of the Ti40 workpiece is improved by using a pulsed current of1 k Hz rather than a direct current.Furthermore, the quality of cavities produced by ECM and the overall material removal rate are determined to be dependent on a combination of operating voltage, electrolyte inlet pressure, cathode feeding rate and electrolyte concentration.By optimizing these parameters, a surface roughness of 0.371 lm has been achieved in conjunction with a specific removal rate of more than 3.1 mm3/A?min. 相似文献
14.
随机恒速运动目标的搜索方程及持续探测概率 总被引:1,自引:1,他引:0
根据目标位置的初始分布和速度分布,给出了随机恒速运动目标在任意时刻位置和速度分布密度函数。定义了探测函数、目标存在和探测不成功的联合概率密度函数和目标存活概率函数,建立了基于目标速度分布的搜索方程并给出了其特征迹线解。在目标初始分布和速度分布均为圆正态分布条件下,分析了搜索方程特征迹线的基本特征和持续探测发现概率积分域的形态。给出了一个以直升机吊放声纳探测潜艇为背景的持续探测发现概率的算例,算例表明,对随机恒速运动目标持续探测的发现概率,与对静止目标进行持续探测的发现概率相似,服从时间的指数规律。 相似文献
15.
16.
Fe3O4/T-ZnOw composites are fabricated by depositing a layer of Fe3O4 film on the surface of tetrapod-shaped ZnO whisker (T-ZnOw) by ferrite plating method. The morphology, structure and magnetic properties of the composites are characterized by scanning electron microscopy (SEM), X-ray diffractometer (XRD) and vibrating-sample magnetometer (VSM), respectively. The effects of temperature and pH value of ferrite plating on the Fe3O4/T-ZnOw composites and the magnetic properties of composites are studied. It is shown that the chemical environment with pH value at 7.5 is most favorable for the ferrite plating processes by analyzing the main peaks intensity of Fe3O4 in the XRD patterns and the average diameters of the Fe3O4 crystalline. The increase of the ferrite plating temperature with pH value around 7.5 benefits the whole encapsulation of T-ZnOw by the Fe3O4 magnetic films. The composites exhibit ferromagnetic properties and show much lower magnetization intensity than bulk samples at the same magnetic field intensity. 相似文献
17.
18.
提出了一种基于低密度粒子图像的微流体粒子图像全场测速技术。经过背景噪声去除、阈值过滤、图像增强等图像预处理过程,获得了高质量的低密度荧光示踪粒子图像。对100对图像进行图像叠加处理,得到了满足互相关算法求解二维速度场的高密度叠加粒子图像。针对宽度为250μm,深60μm的长直微通道开展了覆盖全场不同流体层平面的二维速度测量,并利用多个流体平面的二维速度场实现了微通道内全场速度的构建。研究结果表明:由于图像叠加法去除了像径大但灰度低的背景粒子图像,采用互相关分析能够准确获得分层二维速度场,所构建的全场速度场正确反映了长直微通道内流流场特征。 相似文献
19.
超声速气流中纳秒脉冲放电特性实验研究 总被引:1,自引:0,他引:1
产生超声速导电流体是开展磁流体(MHD)动力技术实验研究的前提,低温超声速条件下产生大体积均匀等离子体有效可行的方法之一是纳秒脉冲介质阻挡放电。介绍了基于马赫数为3吸气式双喉道风洞的超声速纳秒脉冲介质阻挡放电实验系统的基本组成、设计原理和运行情况,分别在静止和马赫数为3超声速条件下对气体电离,测量分析电压和电流波形。得到以下结论:风洞稳定工作时间约为16 s,满足超声速气体放电实验的可靠进行和数据的有效采集;实验条件下,纳秒脉冲介质阻挡放电气体击穿与电场强度值有关,而与电场强度变化率无关;实验条件下,着火电压大小受超声速气流密度波动影响显著,而受气流速度影响较小。另外,气体击穿后的放电状态受超声速气流影响小;气体击穿时刻的电流峰值受着火电压和实验环境中随机自由电子数共同影响。 相似文献
20.
粘性量子流体动力学模型来源于物理学,具有一定的实际意义和理论价值,是半导体研究中的重要组成部分.粘性量子流体动力学模型是由电子密度,电流密度所满足的两个守恒方程和Poisson方程所组成的.一维稳定状态的粘性量子流体动力学模型是本文的研究对象.此模型在有物理意义的狄利克雷边界条件下的一个极限(Inviscid极限)的存在性是我们的研究目标. 相似文献