基于升华法实验研究后掠翼三维边界层的转捩

在西北工业大学的低湍流度风洞,采用升华法研究不同雷诺数下后掠翼上表面的转捩现象。实验发现雷诺数较低时,后掠翼上的转捩由流向不稳定触发,转捩位置在最小压力点之后,转捩分界为一条直线;当雷诺数足够大时,转捩由横流驻波不稳定触发,转捩提前到最小压力点之前,转捩分界呈现尖楔形状。该结果表明升华法不但能够较准确地分辨出后掠翼上的转捩位置,还能够区分不同的转捩机理,判断转捩是由流向不稳定还是横流驻波不稳定触发。此外,实验中还发现在横流驻波不稳定增长较大时,升华法能够提供转捩上游区域边界层内的横流不稳定信息;当横流驻波不稳定进一步增强时,该不稳定受模型表面粗糙度的影响较大,萘的喷涂有可能会影响到升华法的结果。     

Improvement of the SERN nozzle performance by aerodynamic flap design

As continuation of the former study [P. Gruhn et al., Aerospace Science and Technology 4 (2000) 555–565], we examine the flow at a SERN nozzle for a future hypersonic cruise vehicle with help of a nozzle/afterbody wind tunnel model. Main focus is on the flow at the nozzle flap and the separation of the boundary layer at the flap cowl. The location of this separation is determined for different nozzle pressure ratios and different Reynolds numbers. An empirical criterion to predict the separation point at the flap cowl of the nozzle/afterbody model is established.Based on the experiments and recent studies, a geometry for the nozzle flap of the reference configuration ELAC of the Collaborative Research Center 253 of the Aachen University of Technology is suggested. Numerical studies result in an improved axial thrust going along with an improved thrust vector angle for this new flap in the whole examined Mach range between 1.23 and 7. The improvements of up to 11 percent in axial thrust coefficient and up to 15° in thrust vector angle at low Mach numbers exceed the progresses made for the nozzle of the nozzle/afterbody model in the former study.     

三维机翼大迎角低速绕流及其涡控制的数值模拟

通过数值求解三维非定常可压缩雷诺平均Navier-Stokes方程，研究了三维机翼大迎角低速绕流及其带表面周期性吹吸气的流动控制，并探讨了非定常质量引射作为外激发手段对机翼气动力特性的影响，计算表明，在机翼前缘附近的小区域内施加周期性吹吸气进行流动控制，这类外激发手段对三维机翼的大迎角分离流动的控制是可行的，通过选择适当的控制参数，尤其是合适的周期性激振频率，可以有效地改善气动力特性。     

超临界机翼介质阻挡放电等离子体流动控制

为了进一步提高等离子体激励器可控雷诺数,采用测力以及粒子图像测速(PIV)等研究方法,从二维机翼到三维半模,从低雷诺数到高雷诺数,开展了对称布局式介质阻挡放电(DBD)等离子体激励器控制超临界机翼气动特性的试验研究,分析了控制机理,实现了等离子体"虚拟舵面"的功能。结果表明:在雷诺数为2×10⁶的情况下,对称布局式等离子体气动激励能较好地抑制超临界机翼绕流流场分离,使失速迎角推迟2°,最大升力系数提高8.98%。     

Model and full scale high-lift wing wind tunnel experiments dedicated to airframe noise reduction

During landing approach, airframe noise has become a significant contributor to the overall radiated noise from commercial aircraft, when propelled by quiet high-bypass-ratio engines. The major sources of airframe noise are the landing gears and the wing high-lift devices (HLD). In view of European aviation industry to design and build a very large commercial aeroplane, the A3XX, a German National Research Project was initiated, culminating in a series of model- und full scale wind tunnel experiments on HLD. This paper discusses recent results from HLD-studies in the German Dutch Wind Tunnel (DNW) on a 1/7.5 scaled complete model aircraft and the outer section of an A320 full scale wing, employing farfield microphones, unsteady pressure instrumentation and source localization techniques to quantify airframe noise levels and identify the major aeroacoustic sources. The tests provided a baseline data set for the development of noise prediction schemes. Test results obtained on the full scale wing section revealed the importance of excess noise from construction details of a real wing HLD. Tonal components in scale model flap side-edge surface pressure spectra were found to originate from scale model Reynolds number effects. The acoustic effectiveness of initial noise reduction concepts was assessed.     

Design and experimental testing of a control system for a morphing wing model actuated with miniature BLDC motors

The paper deals with the design and experimental validation of the actuation mechanism control system for a morphing wing model. The experimental morphable wing model manufactured in this project is a full-size scale wing tip for a real aircraft equipped with an aileron. The morphing actuation of the model is based on a mechanism with four similar in house designed and manufactured actuators, positioned inside the wing on two parallel lines. Each of the four actuators used a BrushLess Direct Current (BLDC) electric motor integrated with a mechanical part performing the conversion of the angular displacements into linear displacements. The following have been chosen as successive steps in the design of the actuator control system: (A) Mathematical and software modelling of the actuator; (B) Design of the control system architecture and tuning using Internal Model Control (IMC) methodology; (C) Numerical simulation of the controlled actuator and its testing on bench and wind tunnel. The morphing wing experimental model is tested both at the laboratory level, with no airflow, to evaluate the components integration and the whole system functioning, but also in the wind tunnel, in the presence of airflow, to evaluate its behavior and the aerodynamic gain.     

Study of riblet drag reduction for an infinite span wing with different sweep angles

This paper studies the riblet drag reduction effect for an infinite swept wing under a low Reynolds number using a large-eddy simulation. The results show that the drag reduction ratio is not linear under different sweep angles. The maximum drag reduction ratio in this study is 9.5% for a wing with a 45° sweep angle. The local surface streamline angle and turbulence quantities are calculated to analyze the drag reduction mechanism. The results demonstrate that the riblets considerably suppress the Reynolds stresses above the wing upper surface, while the turbulence kinetic energy in the near wake is increased. A possible relaminarization phenomenon is observed at the middle part of the wing. Quasi-two-dimensional flow structures are observed near the wall, and a peak frequency is considered as the dominant frequency of the region.     

飞翼式微型飞行器飞行动力学特性研究

微型飞行器(MAV)非线性飞行力学特性研究是MAV设计中的一个重要环节。由于MAV具有自身尺寸微小,飞行速度低等特点,其空气动力学低雷诺数效应十分明显。飞翼式MAV的非常规气动布局也使得其飞行力学特性与常规飞行器有很大差异。以低雷诺数风洞实验为基础,研究了飞翼式MAV空气动力学特性,提出了1种针对飞翼式飞行器的动阻尼导数计算方法。在飞翼式MAV飞行速度范围内将其运动方程分段线性化以研究其飞行力学特性数值规律。结果表明,飞翼式MAV各项飞行品质指标与常规飞行器存在很大差异,在整个飞行范围内其飞行动力学特性呈非线性变化规律。本文的研究对实现飞翼式MAV自主飞行控制具有重要意义。     

低雷诺数螺旋桨滑流对机翼气动特性的影响研究

深入研究低雷诺数滑流对机翼的影响,能够推进临近空间低速流动机理性研究,提供可靠的气动参数。参考某太阳能无人机,建立单螺旋桨计算模型,采用两叶螺旋桨,通过ICEM网格软件生成具有两个计算域的高质量结构网格,应用滑移网格边界条件,对模型进行数值模拟;分析低雷诺数螺旋桨滑流的发展和机翼在滑流作用下的非定常气动特性,研究不同螺旋桨位置对机翼气动特性的影响,计算结果表明螺旋桨滑流会很大程度地改变机翼表面压力分布和沿翼展的升力分布,对机翼升阻特性有显著影响,同时螺旋桨滑流可以抑制机翼表面层流分离泡的产生。     

小展弦比机翼加装格尼襟翼的低雷诺数试验

通过风洞试验研究了在低雷诺数下加装格尼襟翼的小展弦比机翼气动特性,机翼展弦比为1.67,格尼襟翼为1%~4%弦长高度,试验雷诺数分别为2.0×105和5.0×105.天平测力和表面测压的试验结果表明:低雷诺数下小展弦比机翼加装一定高度的格尼襟翼后,升力系数明显提高,加装1%弦长高度的格尼襟翼还能够提高机翼的升阻比.这是因为在试验雷诺数下,合适高度的襟翼在提高了机翼升力的同时并未显著增大机翼阻力.对比不同试验雷诺数下格尼襟翼的作用效果,表明格尼襟翼能够减少低雷诺数气流分离的不利影响,并且在较小的雷诺数下这种作用更加显著.关于格尼襟翼对低雷诺数层流分离现象的影响,还需要通过细致的流场显示技术进行研究.      

多段翼型缝翼流动非定常性的试验研究

 为了探索缝翼噪声的流体动力学机理,在西北工业大学NF-3低速风洞中用动态压力传感器研究多段翼型在不同条件下绕前缘缝翼流动的非定常性。分析了雷诺数、来流迎角、缝翼和襟翼参数(偏角、缝道宽度和搭接量)对缝翼流动的非定常性影响规律。研究结果表明:缝翼流动非定常性与流动雷诺数、缝翼参数、襟翼参数和来流迎角密切相关,初步揭示了缝道涡的变化趋势和对翼型表面流动的影响以及缝翼噪声产生的原因。该试验研究结果对研究多段翼型噪声产生及抑制方法具有一定的指导意义。     

柔性翼微型飞行器气动特性的实验研究

 柔性翼有望提高微型飞行器(MAV)的抗风能力。为进一步了解柔性翼的气动性能,建立MAV数学模型,并为飞行仿真和飞行控制设计做准备,在低雷诺数风洞中对柔性翼微型飞行器进行了风洞试验,同时采用翼型、机翼平面形状和尺寸大小均相同的刚性翼进行了风洞对比试验。对比结果表明：柔性翼相比于对应的刚性翼,失速迎角较大;柔性翼的最大升力系数较大,但是柔性翼的变形在提高升力的同时也增大了阻力,升阻比的情况较为复杂;在较低雷诺数情况下,柔性翼的纵向静稳定性略优于刚性翼;柔性翼的长周期和短周期模态的衰减特性和阻尼特性略优于刚性翼。     

Aerodynamic design of the high-lift-wing for a Megaliner aircraft

A ‘Megaliner’ aircraft configuration like the Airbus A380 will become a civil transport aircraft lager than all existing designs. Its wing had to be designed not only to give the required cruise performance but also to be compatible with the given airport infrastructure. The aerodynamic design of the high-lift system has to fulfil the resulting targets for the take-off and landing configuration but is also required to have the minimum possible mechanical and structural system complexity, i.e. resulting in a minimum possible weight and cost. After an introduction to constraints of a Megaliner configuration a summary of high-lift wing solutions and the constraints driving the high-lift wing design is given. The experiences in high-lift design on previous Airbus aircraft and the major tools (computational fluid dynamics and windtunnel testing) for the design work and its verification are presented. Also a side view is given to the importance of research programs for the development of new high-lift concepts for future aircraft. The described development work for the Megaliner high-lift wing was driven by the strong requirement for an optimised overall design. Various interactions with the cruise wing design and the design of the support and actuation system are highlighted, which were leading to the best possible balanced solution.     

高雷诺数二维充气机翼构形的气动特性

针对基于二维充气机翼的构形特征进行高雷诺数条件下的气动特性分析.首先通过对二维充气机翼构形特征的设计,建立了描述逼近程度的误差参数和若干模型;进一步运用数值方法,通过与标准翼型的对比,分析充气机翼的气动性能及其误差参数的敏感性.数值结果表明:在高雷诺数条件下,充气机翼的气动性能相对于标准翼型有所降低.同时,结合对流场特征的分析,从机理上解释二维充气机翼与标准翼型气动性能差异形成的原因,即导致总的阻力系数明显增加的主要原因是其凹凸起伏的表面对充气机翼表面压力分布所引起的变化,局部压力升高从而大幅增加了压差阻力.      

低雷诺数多螺旋桨/机翼耦合气动设计

以临近空间太阳能无人机研究为背景,针对高空低雷诺数状态下多螺旋桨/机翼构型进行了耦合气动设计研究。首先,通过对典型多螺旋桨/机翼构型进行气动特性及流动特性分析,提出了以在多螺旋桨滑流影响下构建机翼近壁面理想流态分布形式为核心的低雷诺数多螺旋桨/机翼耦合气动设计思想;然后,基于该耦合设计思想,依次进行了多螺旋桨布局参数设计研究、低雷诺数流态区域二维翼型设计研究以及近似高雷诺数流态区域耦合螺旋桨滑流影响的机翼翼段设计研究;最后,通过相关设计结果的对比分析验证了所提出低雷诺数多螺旋桨/机翼耦合气动设计思想及设计方法的有效性和可靠性。结果表明：与常规仅进行低雷诺数翼型优化得到的设计结果相比较,基于所提出低雷诺数多螺旋桨/机翼耦合设计思想设计得到的多螺旋桨/机翼构型气动特性得到显著改善,在设计状态下,多螺旋桨滑流影响下的机翼阻力相对降低达8.8%,升阻比相对增大达12.1%,由多螺旋桨滑流为机翼气动特性带来的不利影响亦得到约64.5%的补偿和改善。     

基于自然激励技术的颤振边界预测

为了预测紊流激励条件下机翼的颤振边界,基于自然激励技术提取紊流响应的自由衰减信号,采用矩阵束方法识别模态参数,最后通过Z-W(Zimmerman-Weissenburger)方法计算稳定性判据,拟合判据变化曲线并外推颤振边界.对平板机翼模型进行了数值仿真分析,对单独机翼模型风洞颤振试验数据进行了计算.结果表明:采用自然激励技术与矩阵束方法能够较准确地识别紊流激励响应的模态参数,频率识别误差小于6％,阻尼比识别误差小于30％,结合Z-W方法能够在较低风速较早地预测颤振边界,有助于提高试验的安全性.     

后掠机翼人工转捩最佳粗糙带高度数值预测

介绍了基于当地变量的γ-Re_θ转捩模型,并将该模型应用到后掠机翼的转捩预测和人工转捩最佳粗糙带高度以及人工转捩技术能够模拟的大气飞行雷诺数的确定中。为检验γ-Re_θ转捩模型对后掠机翼转捩的预测能力,对ONERA M6机翼和DLR-F4标模机翼进行了边界层转捩预测,采用结构化网格和有限体积法求解雷诺平均Navier-Stokes(RANS)方程,得到了机翼表面的摩擦阻力系数分布,从而可以得到相应的转捩位置,预测得到的转捩位置与试验结果比较吻合,说明该模型对后掠机翼转捩预测是可信的。最后在DLR-F4标模机翼上表面固定了粗糙带,通过相同的方法得到了转捩位置,从而确定了马赫数为0.785、雷诺数为3.0×10⁶时最佳粗糙带高度为0.11 mm;通过不断增大雷诺数使自由转捩位置不断向前缘移动,验证了人工转捩对大气飞行雷诺数的模拟能力。结果表明,在最佳粗糙带高度为0.11 mm下,可以实现对大气飞行高雷诺数的模拟。     

昆虫尺度微型仿生飞行器的研究

微型仿生飞行器的研究涉及仿生学原理、准稳态气动力和原理样机的研制等。概述了上海交通大学针对昆虫尺度的微型仿生飞行器的新颖的设计和加工方法。该方法确保了零部件空间位置的合理安排,从而减少了零部件的装配难度。具体来说,压电驱动器的设计考虑了电气隔离和装配问题;传动机构与机身整合成一个部件,避免了相互之间的装配。翅脉的纤维方向进行了合理的布置,使得翅膀拥有高强度和高刚度。最终,研制的压电驱动微型仿生飞行器重84mg,翼展35mm,在100Hz的拍打共振频率下可以产生±60°的拍打角度,能产生足够的升力实现起飞。     

机翼跨声速抖振数值模拟及模态分析

绕机翼的跨声速抖振流动是典型的复杂不稳定流动，对其非定常特性及失稳机制的研究具有重要的工程和学术价值。通过非定常雷诺平均Navier-Stokes（URANS）仿真方法和动模态分解（DMD）分析手段，研究了CRM（Common Research Model）等典型机翼的跨声速抖振流动特性及其主要失稳模态。数值仿真结果表明机翼的跨声速抖振表现为多失稳模式下的宽频特性。除了激波的弦向失稳，还会伴随发生激波的展向失稳，它们都表现为低频特性。翼梢处的高频响应可能是由激波诱导的低频失稳与翼尖涡相互耦合形成。DMD分析结果显示机翼展长和后掠因素诱导了激波展向失稳模态。本研究对抖振流动的物理建模、控制及理解相关的气动弹性现象具有指导意义。     

Turbulent boundary layer separation control using plasma actuator at Reynolds number 2000000

An experimental investigation was conducted to evaluate the effect of symmetrical plasma actuators on turbulent boundary layer separation control at high Reynolds number. Compared with the traditional control method of plasma actuator, the whole test model was made of aluminum and acted as a covered electrode of the symmetrical plasma actuator. The experimental study of plasma actuators' effect on surrounding air, a canonical zero-pressure gradient turbulent boundary, was carried out using particle image velocimetry(PIV) and laser Doppler velocimetry(LDV) in the 0.75 m × 0.75 m low speed wind tunnel to reveal the symmetrical plasma actuator characterization in an external flow. A half model of wing-body configuration was experimentally investigated in the  3.2 m low speed wind tunnel with a six-component strain gauge balance and PIV. The results show that the turbulent boundary layer separation of wing can be obviously suppressed and the maximum lift coefficient is improved at high Reynolds number with the symmetrical plasma actuator. It turns out that the maximum lift coefficient increased by approximately 8.98% and the stall angle of attack was delayed by approximately 2° at Reynolds number2 ×10~6. The effective mechanism for the turbulent separation control by the symmetrical plasma actuators is to induce the vortex near the wing surface which could create the relatively largescale disturbance and promote momentum mixing between low speed flow and main flow regions.