基于STM32F429的全向运动平台的运动控制

全向运动平台系统是可以实现人体在各个方位行走的2D运动平台。针对实现人体在全向运动平台稳定行走的运动控制,采用加入观测器的一阶控制算法对平台运动控制进行探究。先通过MATLAB软件进行算法的仿真,验证方法的可行性;再通过现场测试,验证控制算法的有效性。最终试验表明,加入观测器的一阶控制算法可对全向运动平台实现有效的运动控制。此运动控制策略的探究为全向运动平台的运动控制提供了一种可行的控制思路和方案。     

周期平均控制下固定翼双旋弹角运动特性分析

针对应用在固定翼双旋弹上的一种周期平均控制方法,通过对弹体修正组件滚转角进行傅里叶变换,得到了双旋弹在周期平均控制下角运动方程的模型,进而分析了周期平均控制下固定翼双旋弹的角运动响应,并根据双旋弹角运动特性和执行机构的性能限制给出了周期平均控制角频率的设计方法。引进2种具体的周期平均控制方案作为分析对象,并通过六自由度弹道仿真进行了验证。结果表明,对固定翼双旋弹角运动响应的分析能够反映周期平均控制的特性,周期平均控制角频率的设计方法可以设计出合理的角频率。     

两位五通电动气阀动态特性研究

将电动气阀的工作过程分为电动过程和气动过程，建立了两过程的动力学模型。分别对电动过程和气动过程的响应特性进行仿真，并与试验结果比较，验证了动力学模型的正确性。分析了控制气体压力、最大气隙以及工作电压等因素对电动过程的影响。     

A mathematical model of transforming the vertical takeoff and landing aircraft with a disk wing at maneuvering (on a deck)

The motion of blades relative to the disk wing at the extension and retraction modes is defined. The general solution is obtained including the fuselage motion under the action of control or external disturbance.     

Influence of Interference Effects of the Rotor on the Launch Dynamics of Gliding Unmanned Aerial Vehicle

A mathematical model of the gliding unmanned aerial vehicle (UAV) motion is performed taking into account the interference effect of the main rotor on the UAV. Calculated values are presented for the interference addition to the aerodynamic coefficients of forces and moments on the UAV path section close to the carrier. The problems of stabilization and control are solved, providing stability of the UAV motion at the launch with due account of the aerodynamic interference and the effect of short-term upper stage engine operation, as well as a safe distance between the carrier and the UAV during their simultaneous motion.     

克服旋转飞行器螺旋运动的方法研究

旋转飞行器虽然具有内在稳定性，但在飞行过程中一些不确定因素会导致飞行器产生螺旋运动，而非理想的关于角动量矢量纯粹的旋转运动。结合旋转飞行器自身的特点，借鉴自旋卫生的被动章动阻尼的方法，提出了一种通过主动控制飞行器内部质量块的运动使得飞行器碑的惯量主轴发生偏移，惯量矩阵由原来的对称阵变为含有非零非对角元素的矩阵，从而改变飞行器的姿态角运动来克服螺旋运动的方法，这将有助于提高旋转飞行器的资态控制精度。以某型旋转飞行器为背景进行仿真研究，计算结果证实了该方法的有效性和可行性。     

舵面破损对飞机轴间运动耦合飞行品质的影响

为研究舵面破损对电传控制飞机轴间运动耦合飞行品质的影响,选取了能够反映飞机多轴运动耦合特性的飞行品质评定任务,建立了舵面破损飞机的飞行动力学模型,选取了适用于表征飞机轴间运动耦合程度的特征参数,形成了基于任务的角速率指令式电传控制飞机轴间运动耦合飞行品质的评定方法。采用该方法对具有不同舵面破损程度的算例飞机开展了飞行品质评估试验,得到了能够量化舵面破损对角速率指令式电传控制飞机飞行品质影响的特征参数取值规律。研究结果对于舵面破损情形下飞机飞行安全与作战效能评估等均有一定的理论参考价值。     

一种环境探测球形移动机器人的运动控制

 球形移动机器人具有结构紧凑、运动灵活等特点,在环境探测等应用领域具有独特优势。介绍了一种新型的、带有双摄像头的环境探测球形移动机器人BHQ-2的结构与运动原理,并对其运动控制问题进行了研究。由于该球形机器人属于非完整约束系统,其不存在位置级的运动学逆解,因此从速度级上讨论了它的运动控制问题。基于旋量理论推导了该球形移动机器人的速度雅可比矩阵,采用广义逆的解法求得了它的速度逆解,并采用可控性李代数证明了BHQ-2球形移动机器人系统是满秩的,因此该机器人系统是完全非完整的并且是可控的。基于运动学速度逆解对BHQ-2球形移动机器人进行了直线和圆形运动轨迹的仿真和实验,仿真和实验结果验证了该球形机器人的可控性及速度逆解的正确性。     

Control of flight vehicles with the adjustable center of mass

We resolve a problem how to control the longitudinal angular motion of flight vehicles (FV) having a system to displace the center of mass in the transverse direction. A structure is determined and a control law is established to start up and shutdown the engines. Formulas to determine the control parameters are obtained.     

Efficiency Estimation of Electrothermal Thrusters Use in the Control System of the Technological Spacecraft Motion

The influence of various control systems of the orbital motion of a technological spacecraft on the level of microacceleration of its internal environment is simulated. Conclusions are drawn about the effectiveness of control systems with different actuators for realization of certain gravitationally sensitive processes onboard a spacecraft.     

Gain Scheduling Control of Nonlinear Shock Motion Based on Equilibrium Manifold Linearization Model

The equilibrium manifold linearization model of nonlinear shock motion is of higher accuracy and lower complexity over other models such as the small perturbation model and the piecewise-linear model. This paper analyzes the physical significance of the equi- librium manifold linearization model, and the self-feedback mechanism of shock motion is revealed. This helps to describe the stability and dynamics of shock motion. Based on the model, the paper puts forwards a gain scheduling control method for nonlinear shock mo- tion. Simulation has shown the validity of the control scheme.     

三角翼机翼摇滚主动控制多学科耦合数值模拟

细长机身和大后掠机翼气动构型的飞行器大攻角飞行时,由于缺少横向阻尼,易发生以绕体轴滚转振动为主的摇滚运动,飞行安全受到严重威胁。针对三角翼摇滚问题,采用动网格技术,建立了气动、运动和控制多学科耦合的数值模拟方法。通过耦合非定常Navier-Stokes方程、刚体运动方程和经典控制律,采用控制面差动偏转的方式对三角翼摇滚主动控制过程进行了数值模拟,并分析了不同控制状态下三角翼受控滚转的运动特性。在来流马赫数为0.3的条件下,实现了80°后掠三角翼摇滚现象的有效控制。     

基于闭环控制的带翼导弹虚拟飞行数值模拟

通过耦合求解非定常Navier-Stokes方程、刚体六自由度（6DOF）运动方程及舵偏控制律,发展了一套虚拟飞行数值模拟平台,对基本带翼导弹外形进行了虚拟飞行数值模拟研究。流场求解采用基于结构网格的有限体积法,时间推进采用双时间步法,使用刚性重叠动网格技术模拟舵与弹身的相对运动,采用四阶Runger-Kutta方法求解运动方程组,舵偏控制律采用基于比例-积分-微分（PID）的反馈控制。模拟结果表明：发展的虚拟飞行数值模拟平台能够处理包含复杂运动边界的非定常运动问题,可以为非定常气动力建模提供数据、预示飞行器稳定性及检验飞行控制律,该模拟平台具备一定的工程应用价值。     

基于数值虚拟飞行技术的飞行器动态特性分析

基于结合结构重叠网格、闭环PID控制器、舵偏控制律、刚体六自由度运动和非定常Navier-Stokes方程求解等模块的数值虚拟飞行技术,对“起源号”返回舱、基本带翼导弹外形的多自由度非定常运动、受控特性及控制参数的整定开展了模拟。分析了不同自由度（DOF）下飞行器的运动特性,飞行器受扰动后的稳定性及控制参数的整定。计算结果表明：利用数值虚拟飞行技术可有效地开展复杂流动下飞行物体非线性运动问题的研究,对研究飞行器在非线性流动下的动态特性、受控特性、流动机理研究以及控制律的设计检验具有较高的工程价值和应用前景。     

飞机自动着陆纵向块对角控制器设计

在阐述了块对角控制理论和分析飞机运动特性的基础上,把飞机纵向运动方程转化为块对角非线性系统,并设计了飞机自动着陆纵向块对角控制器。仿真结果表明,该控制器能够控制飞机自动着陆,跟踪性能良好。     

导弹运动方程的逆解析解

针对在采用反馈线性化理论设计导弹飞行控制系统时控制器算法对导弹逆模型的要求 ,推导了导弹运动方程的逆解析解 ,包括导弹质心运动的运动学方程及其动力学方程的逆解析解、姿态运动的运动学方程及其动力学方程的逆解析解 ,详细给出了逆模型的求解过程 ,为一类飞行控制系统运用全局线性化设计奠定了基础。最后 ,结合工程应用进行了仿真计算 ,仿真结果表明逆解析解的推导是正确的     

多维磁悬浮隔振系统动力学模型与控制策略

磁悬浮隔振系统具有非线性、强耦合、高响应、宽频带等特点，系统的隔振控制目标与其定子和浮子之间的位置约束相互制约，这对系统的精密控制提出了较大的挑战。为解决该问题，建立了面向控制的六自由度磁悬浮隔振系统非线性动力学模型，并提出了双闭环控制策略，使系统在低频到中高频带内实现隔振控制，在极低频带内实现跟踪控制。采用PD定点控制算法，在MATLAB/Simulink环境中开发了控制系统仿真程序，通过分析不同扰动频率下浮子的绝对运动响应以及定子与浮子之间的相对运动响应，获得了系统的隔振控制与跟踪控制仿真结果。搭建了磁悬浮隔振平台样机测试系统，验证了动力学模型的正确性和控制策略的有效性。     

Robust and optimal attitude stabilization of spacecraft with external disturbances

This paper presents a robust and optimal three-axis attitude control scheme for the rigid body motion with external disturbances, in which a worst-case design that the external disturbance signal maximizes the same performance index that the control input minimizes is assumed. After presenting a robust control law for the three-axis attitude control of the rigid body motion with external disturbances, the optimality property of the robust control law is investigated based on the minimax approach and the inverse optimal approach. A numerical example is given to illustrate the theoretical result presented in this paper.     

Dynamic characteristics analysis and flight control design for oblique wing aircraft

The movement characteristics and control response of oblique wing aircraft (OWA) are highly coupled between the longitudinal and lateral-directional axes and present obvious nonlinear-ity. Only with the implementation of flight control systems can flying qualities be satisfied. This arti-cle investigates the dynamic modeling of an OWA and analyzes its dynamic characteristics. Furthermore, a flight control law based on model-reference dynamic inversion is designed and ver-ified. Calculations and simulations show that OWA can be trimmed by rolling a bank angle and deflecting the triaxial control surfaces in a coordinated way. The oblique wing greatly affects lon-gitudinal motion. The short-period mode is highly coupled between longitudinal and lateral motion, and the bank angle also occurs in phugoid mode. However, the effects of an oblique wing on lateral mode shape are relatively small. For inherent control characteristics, symmetric deflection of the horizontal tail will generate not only longitudinal motion but also a large rolling rate. Rolling moment and pitching moment caused by aileron deflection will reinforce motion coupling, but rud-der deflection has relatively little effect on longitudinal motion. Closed-loop simulations demon-strate that the flight control law can achieve decoupling control for OWA and guarantee a satisfactory dynamic performance.     

Analytical Synthesis of Stabilization Laws for Spacecraft Orbit Attitude Using Information on an Angle and the Full Vector of Angular Velocity

The problem of stabilizing the spacecraft orbit attitude was solved analytically for the sixth order model of its rotary motion with the use of the output feedback control synthesis that is based on decomposition of a control object. Numerical simulation data are presented.