Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

Diamond wheel grinding characteristics of 3D orthogonal quartz fiber reinforced silica ceramic matrix composite

Fiber-reinforced silica ceramic matrix composites (SiO_2f/SiO₂) have gained extensive attention in recent years for its applications in aeronautics field such as radar radome and window. However, the machining properties and mechanism of the material remain unclear. The features and mechanical properties of the material itself have a significant influence on both its machining characteristics and surface integrity. Thus, a full-factor grinding experiment is conducted using a 3D orthogonal SiO_2f/SiO₂ aiming to obtain its machining characteristics. The effects of grinding parameters and tools on the grinding force, surface roughness, and material damage type are investigated using a dynamometer, Scanning Electron Microscope (SEM), and Acoustic Emission (AE) analysis. The AE frequency band is analyzed, and a semi-analytical force model is established to study the difference between a single grain and wheel grinding. It was found that the changes in surface roughness correlate with the changes in grinding force, with fiber fracture being the main reason behind the increase in grinding force. Finally, the material removal mechanism was studied based on the AE analysis. It was found that the removal mechanism is fiber fracture dominated with matrix crack and debonding, and the primary sources of energy consumption are fiber fracture and friction.     

Minimum quantity lubrication machining of aeronautical materials using carbon group nanolubricant: From mechanisms to application

It is an inevitable trend of sustainable manufacturing to replace flood and dry machining with minimum quantity lubrication(MQL) technology. Nevertheless, for aeronautical difficult-tomachine materials, MQL couldn’t meet the high demand of cooling and lubrication due to high heat generation during machining. Nano-biolubricants, especially non-toxic carbon group nano-enhancers(CGNs) are used, can solve this technical bottleneck. However, the machining mechanisms under lubrication of CGNs are uncl...     

Influences of milling and grinding on machined surface roughness and fatigue behavior of GH4169 superalloy workpieces

Surface topography of superalloy GH4169 workpieces machined by milling and grinding is different significantly. Meanwhile, surface roughness, as one of the main indicators of machined surface integrity, has a great influence on the fatigue behavior of workpieces. Based on analyzing the formation mechanism and characteristics of surface roughness utilizing different machining processes and parameters, the machined surface roughness curve can be decoupled into two parts utilizing frequency spectrum analysis, which are kinematic surface roughness curve and stochastic surface roughness curve. The kinematic surface roughness curve is influenced by machining process,parameters, geometry of the cutting tool or wheel, the maximum height of which is expressed as R'_z.By subtracting the kinematic part from the measurement curve, the stochastic surface roughness curve and its maximum height R'_zcan be obtained, which is influenced by the defects of cutting tool edge or abrasive grains, built-up edges(BUE), cracks, high frequency vibration and so on. On the other hand, the results of decoupling analysis of surface roughness curves indicate that Raand Rz values of milling GH4169 are 2–5 times and 1–3 times as high as those of grinding, while R'_zvalue of milling is 13.85%–37.7% as high as that of grinding. According to the results of fatigue life tests of specimens machined by milling and grinding, it can be concluded that fatigue behavior of GH4169 decreases with the increase of R'_zmonotonically, even utilizing different machining processes.     

基于灰色关联分析的微量润滑系统工艺参数优化

为解决钛合金铣削加工中微量润滑系统工艺参数优化问题,采用正交试验法以空气流量、切削液用量、切削液浓度为变量,表面粗糙度Ra和切削力为评价指标开展钛合金微量润滑铣削试验。基于灰色关联和主成分分析法对微量润滑系统工艺参数进行多目标优化,通过分析各因素对灰色关联度的影响规律,确定了最佳系统参数组合为空气流量90L/min、切削液用量15mL/h、切削液浓度70%。经验证优化后的工艺参数可有效提高工件表面质量,减小切削力,为合理选择微量润滑系统工艺参数提供了参考依据。     

Effect of creep feed grinding on surface integrity and fatigue life of Ni3Al based superalloy IC10

Ni₃Al-based superalloy IC10 is widely used in high temperature components of aero-engines because of its superior mechanical properties. In this paper, the creep feed grinding properties of IC10 were investigated experimentally. The effects of grinding parameters on the grinding forces and temperature were examined. Moreover, the influences of surface roughness and hardening on the high-cycle fatigue life of IC10 specimens were studied. To control the creep feed grinding parameters and enhance the fatigue life of IC10 components, the experimental results were summarized to offer a useful reference point. It is concluded that, the grinding depth is the most important factor which influencing the grinding forces and temperature; the surface roughness is the main and unfavorable factor on the fatigue life of IC10, while the surface hardening has a positive influence on the fatigue life; to obtain a better surface quality and improve the fatigue life of IC 10, the recommended grinding parameter domain involves wheel speed ∈ [15, 20] m/s, feed rate ∈ [150, 200] mm/min, and grinding depth ∈ [0.4, 0.5] mm.     

Interference and grinding characteristics in ultra-precision grinding of thin-walled complex structural component using a ball-end grinding wheel

As for ultra-precision grinding of difficult-to-process thin-walled complex components with ball-end grinding wheels, interference is easy to occur. According to screw theory and grinding kinematics, a mathematical model is established to investigate the interference and grinding characteristics of the ball-end wheel. The relationship between grinding wheel inclination angle, C axis rotation angle, grinding position angle and grinding wheel wear are analyzed. As the grinding wheel inclination angle increases, the C axis rotatable range decreases and the grinding position angle increases. The grinding position angle and wheel radius wear show a negative correlation with the C axis rotation angle. Therefore, a trajectory planning criteria for increasing grinding speed as much as possible under the premise of avoiding interference is proposed to design the grinding trajectory. Then grinding point distribution on the ball-end wheel is calculated, and the grinding characteristics, grinding speed and maximum undeformed chip thickness, are investigated. Finally, a complex structural component can be ground without interference, and surface roughness and profile accuracy are improved to 40.2 nm and 0.399 μm, compared with 556 nm and 3.427 μm before ultra-precision grinding. The mathematical model can provide theoretical guidance for the analysis of interference and grinding characteristics in complex components grinding to improve its grinding quality.     

Characteristics of surface and subsurface of formed thread parts by axial-infeed thread rolling process

The thread rolling process has been widely applied to manufacture high-performance thread parts. In this process, the evolutions of surface and subsurface are frequently introduced, which affect the working performance of manufactured parts. In this study, an axial-infeed thread rolling process (ATRP) is employed, and the macro-meso surface characteristics under different lubrications and operating conditions are investigated. Moreover, the distributions of microstructure and hardness on the subsurface of formed tooth are analyzed in detail, along with the study of stress state and yield strength change. It is found that the MoS₂ grease is more effective in reducing the surface roughness and defects than the lubrication oil and water-base graphite during the ATRP process. Increasing rolling speed improves the quality of surface morphology and can reduce the surface roughness. On the subsurface of bottom and flank, intensive shear stress occurs in a narrow region, resulting in the elongation and refinement of the grains and increasing the low angle grain boundary fraction. Based on the grain size and plastic strain, the yield strength is predicted. The maximum yield strength and hardness on the bottom of formed tooth are improved by 41.2% and 39.4%, respectively.     

基于碟形砂轮磨齿的面齿轮包络残差研究

介绍了采用碟形砂轮磨削面齿轮的原理及过程,研究了齿廓包络和齿宽包络两种包络方式产生包络残差的机理.分别建立了两种加工方式下包络残差的计算模型和方法,并研究了所产生包络残差的特点.通过数值算例分析了包络过程中刀具周向进给角度、齿宽方向进给量以及碟形砂轮外径对齿面包络残差的影响规律.计算结果表明:齿宽包络比齿廓包络具有更高的效率.进行了以齿廓包络方式的面齿轮磨齿加工实验,当刀具周向进给角度分别取为2°,1°,0.5°及0.2°时,齿面表面粗糙度逐渐明显提高,齿面磨削加工印痕的数目和方向与包络仿真计算结果一致.初步证明根据包络残差计算结果选取合适的进给量参数,可以保证面齿轮磨齿加工的表面粗糙度水平并能提高加工效率.      

Fretting wear behaviour of machined layer of nickel-based superalloy produced by creep-feed profile grinding

Fretting wear has an adverse impact on the fatigue life of turbine blade roots. The current work is to comparatively investigate the fretting wear behaviour of the nickel-based superalloy surfaces produced by polishing and creep-feed profile grinding, respectively, in terms of surface/subsurface fretting damage, the friction coefficient, wear volume and wear rate. Experimental results show that the granulated tribolayer aggravates the workpiece wear, while the flat compacted tribolayer enhances ...     

Development of a new high-shear and low-pressure grinding wheel and its grinding characteristics for Inconel718 alloy

Nickel-based alloy has been widely used due to its outstanding mechanical properties.However, Nickel-based alloy is a typical difficult-to-machine material, which is a great constrain for its application in the manufacturing field. To improve the surface quality of the ground workpiece, a new high-shear and low-pressure grinding wheel, with high ratio of tangential grinding force to normal grinding force, was fabricated for the grinding of selective laser melting(SLM) manufactured Inconel718 all...     

Investigation on surface integrity of electron beam melted Ti-6Al-4 V by precision grinding and electropolishing

Electron beam melting (EBM), as an excellent Additive Manufacturing (AM) technology, enables the printing of Ti-6Al-4 V alloy for a wide range of applications such as aerospace and biomechanical industries. It improves functionality and integrity of components and negates complexities in assembly processes. However, due to the poor surface and sub-surface integrity represented by the rough surface finish and low dimensional accuracy, achieving a favorable surface condition is quite challenging. Therefore, post processing becomes essential for these electron beam melted (EBM-ed) Ti-6Al-4 V alloys. Being the most common technique to improve such parts, milling of Ti-6Al-4 V alloy is very challenging and resulting tool wear issues, due to its unique material properties. Thus, this paper presents a comprehensive study on the surface integrity of EBM-ed Ti-6Al-4 V parts processed by precision grinding and electropolishing, aiming to qualitatively and quantitatively clarify the interrelation between process parameters and processed surface quality. The surface and subsurface characteristics such as profile accuracy, surface roughness, microstructure, defective layer and residual stress before and after post processing were compared and evaluated. The results show that by precision grinding, the profile accuracy was improved from over 300 µm PV to 7 µm PV, while surface roughness (R_a) was reduced from 30 µm to about 2 µm. The layer with partially melt particles was removed, but introduced a deformed subsurface layer with more residual stress. Then by applying electropolishing, the residual stress was released and the deformed layer was removed. In addition, R_a was further reduced to 0.65 µm. The research can serve as a reference for the integration of post machining processes with AM.     

Design and experimental study of a micro-groove grinding wheel with spray cooling effect

The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming.     

Grindability and Surface Integrity of Cast Nickel-based Superalloy in Creep Feed Grinding with Brazed CBN Abrasive Wheels

The technique of creep feed grinding is most suitable for geometrical shaping, and therefore has been expected to improve effectively material removal rate and surface quality of components with complex profile. This article studies experimentally the effects of process parameters (i.e. wheel speed, workpiece speed and depth of cut) on the grindability and surface integrity of cast nickel-based superalloys, i.e. K424, during creep feed grinding with brazed cubic boron nitride (CBN) abrasive wheels. Some important factors, such as grinding force and temperature, specific grinding energy, size stability, surface topography, microhardness and microstructure alteration of the sub-surface, residual stresses, are investigated in detail. The results show that during creep feed grinding with brazed CBN wheels, low grinding temperature at about 100 °C is obtained though the specific grinding energy of nickel-based superalloys is high up to 200-300 J/mm³. A combination of wheel speed 22.5 m/s, workpiece speed 0.1 m/min, depth of cut 0.2 mm accomplishes the straight grooves with the expected dimensional accuracy. Moreover, the compressive residual stresses are formed in the burn-free and crack-free ground surface.     

镍基高温合金GH4169磨削参数对表面完整性影响

研究了用单晶刚玉砂轮磨削镍基高温合金GH4169时,磨削参数对表面完整性中的表面特征(表面粗糙度、表面形貌、表面显微硬度和表面残余应力)的影响,以期优化磨削参数.砂轮速度依次选择15,20,25m/s,磨削深度分别选择50,100,150μm,工件速度分别选择5,10,15m/min.研究结果表明:表面粗糙度对工件速度的变化最敏感,表面显微硬度对砂轮速度变化最敏感,表面残余应力对砂轮速度变化最敏感;同时表明了磨削参数对磨削表面形貌、显微硬度梯度、微观组织、残余应力梯度的影响,揭示了表面完整性中的变质层形成规律.其塑性变形层在5～10μm,显微硬度变化影响层为80～100μm,残余应力影响层厚度为80～200μm,其为磨削镍基高温合金表面完整性控制研究提供相关的实验数据基础.      

Cooling and lubrication techniques in grinding:A state-of-the-art review,applications, and sustainability assessment

Grinding technology is an essential manufacturing operation, in particular, when a component with a superfinishing and an ultra-resolution is yearned. Meeting the required strict quality checklist with maintaining a high level of productivity and sustainability is a substantive issue. The recent paper outlines the lubrication and cooling technologies and mediums that are used for grinding. Furthermore, it provides a basis for a critical assessment of the different lubrication/cooling techniques ...     

超磁致伸缩执行器驱动的射流伺服阀参数优化

为提高射流伺服阀的性能,提出了一种超磁致伸缩执行器驱动的直动式射流伺服阀.采用磁场有限元分析的方法,建立了超磁致伸缩执行器输出电流与输出位移的关系,分析了线圈结构对其输出位移的影响,并给出了所设计执行器的实验曲线.结合所设计的射流伺服阀的特点,以能量传递效率最大为优化目标,建立了射流结构与射流效率的关系方程,求出了所设...     

Effects of surface roughness on the aerodynamic performance of a high subsonic compressor airfoil at low Reynolds number

The aerodynamic performance of compressor airfoil is significantly affected by the surface roughness at low Reynolds number (Re). In the present study, numerical simulations have been conducted to investigate the impact of surface roughness on the profile loss of a high subsonic compressor airfoil at Re = 1.5 × 10⁵. Four roughness locations, covering 10%, 30%, 50% and 100% of the suction surface from the leading edge and seven roughness magnitudes (R_a) ranging from 52 to 525 μm were selected. Results showed that the surface roughness mainly determined the loss generation process by influencing the structure of the Laminar Separation Bubble (LSB) and the turbulence level near the wall. For all the roughness locations, the variation trend for the profile loss with the roughness magnitude was similar. In the transitionally rough region, the negative displacement effect of the LSB was suppressed with the increase of roughness magnitude, leading to a maximum decrease of 14.6%, 16.04%, 16.45% and 10.20% in the profile loss at R_a = 157 μm for the four roughness locations, respectively. However, with a further increase of the roughness magnitude in the fully rough region, the stronger turbulent dissipation enhanced the growth rate of the turbulent boundary layer and increased the profile loss instead. By comparison, the leading edge roughness played a dominant role in the boundary layer development and performance variation. To take fully advantage of the surface roughness reducing profile loss at low Re, the effects of roughness on suppressing LSB and inducing strong turbulent dissipation should be balanced effectively.     

Profile error compensation in precision grinding of ellipsoid optical surface

Optical glass elements with the ellipsoidal surface are used in many critical aerospace instruments, such as satellites, telescope and cameras. Their optical performance is mainly affected by profile accuracy and surface quality. In this paper, a rectangular ellipsoid surface is precisely ground on a BK7 optical glass blank by grating scanning grinding path with a three-axis CNC precision surface grinder. A profile error compensation procedure for ellipsoidal grinding is proposed based on the error analysis about the primary error sources in the XY and YZ projection planes during the grinding process. The mathematical prediction models of the wheel arc profile error, the measurement and wear error of the grinding wheel radiuses are established. By applying the proposed error compensation procedure, the profile accuracy of the ellipsoidal surface was improved from 4 μm to 2 μm in the XY plane, and improved from 15 μm to 5 μm in the YZ plane.     

直升机起落架轮轴碳化钨磨削工艺研究

直升机起落架轮轴表面喷涂碳化钨涂层后可提高轮轴的耐磨性和耐腐蚀性,但是受超声速火焰喷涂工艺方法的限制,喷涂碳化钨的轮轴必须通过磨削工艺保证表面质量和尺寸精度,然而轮轴的弱加工刚性和涂层的高耐磨性导致磨削过程中易产生让刀、颤刀等现象,造成零件磨削质量不合格。首先采用正交试验法研究四种精磨工艺参数对于磨削表面粗糙度的影响;然后研究装夹工具和磨削策略对于零件圆柱度的影响;最后加工并收集15 件轮轴的各段外圆尺寸并计算其过程能力指数。结果表明：选择高砂轮线速度、小切深以及适中的砂轮轴向进给速度与工件线速度可以获得粗糙度为0.4 μm 的零件表面,增加装夹工具的夹持长度和刚性并采用“粗磨—精磨—光磨”策略可保证零件外圆的圆柱度不大于0.01 mm。轮轴过程能力指数的计算结果不小于1.33,验证了整个磨削工艺的可靠性与稳定性。