共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
用广义尾流模型计算了悬停旋翼下洗流场,在此基础上用工程方法计算了有旋翼尾流干扰和无旋翼尾流干扰两种条件下的某空空导弹的气动特性.将气动力计算和初始弹道计算相耦合,计算了导弹的初始弹道,给出了气动参数沿初始弹道的变化曲线,并对计算结果进行了分析.数值计算结果表明旋翼下洗流对导弹的气动特性和初始弹道有显著的影响,在尾迹区内导弹的气动参数变化较大,尾迹区外气动参数变化比较平缓;弹道参数与无下洗流干扰条件下相比也有很大不同.本文揭示了旋翼尾流对导弹的气动干扰规律和导弹的初始运动规律,研究成果对改进机载导弹的发射技术和弹道控制有重要的意义. 相似文献
3.
为了比较反舰导弹在不同的末端机动方式下,当有舰空导弹拦截时哪种突防效果更好,从工程应用的角度出发,考虑反舰导弹受多种因素(包括干扰、建模误差、海情、不确定性等)的影响,并同时考虑舰空导弹的前置角约束和死区约束,建立了反舰导弹与舰空导弹的对抗模型。其中,反舰导弹采用的是基于过载控制方法设计的全弹道仿真模型,舰空导弹则采用三阶简化模型。根据舰空导弹初始拦截位置的不同,设定不同的初始仿真条件,在计算机上进行多次打靶,应用蒙特卡洛法分别计算反舰导弹在不同机动方式下的突防概率。仿真结果表明,在有舰空导弹拦截的情况下,反舰导弹进行螺旋机动时,其突防效果最好,摆式机动次之,然后是纵向蛇行机动,最后是航向蛇行机动,而突防效果最差的则是反舰导弹不进行末端机动。 相似文献
4.
拟合导弹主动段弹道并估计其弹道参数是天基红外系统(SBIRS)的重要任务之一。首先采用三次样条函数对导弹主动段弹道进行描述,并建立主动段弹道的运动模型和测量模型;其次采用最大似然估计方法将导弹弹道估计问题转化为非线性最小二乘准则下的样条系数和样条节点分布最优估计问题;最后利用投影定理将样条系数估计和样条节点分布估计分离开来,并通过迭代逼近给出了最优样条节点数的确定方法。仿真实验结果表明,所提方法不仅对主动段弹道的拟合精度高,而且还减少了待估参数的数目,简化了求解过程,可在无先验信息条件下较好地解决导弹主动段弹道的估计问题。 相似文献
5.
结合某型导弹六自由度弹道仿真,将极大似然法作为弹道重构的主要手段,详细讨论了用于仿真验证过程的弹道重构方法和步骤,并给出了弹道重构的计算模型,以赛氏系数为性能指标,给出一种模型验的定量方法,这里特别调用于弹道重构的数据应具有独立性,仿真结果表明,利用弹道重构对导弹六自由度弹道仿真模型进行验证是有效的。 相似文献
6.
7.
某型导弹发射内弹道数值仿真 总被引:2,自引:0,他引:2
建立某型潜射导弹的内弹道方程组,对内弹道方程组进行了仿真计算,研究了变深度发射内弹道参数的变化规律及发射深度变化对导弹离筒参数的影响。 相似文献
8.
9.
基于vega的导弹飞行视景仿真 总被引:1,自引:1,他引:0
为解决某公司某重点型号在飞行中的控制问题,首先介绍了虚拟现实技术(Virtual Reality)和计算机仿真(Computer Simulation)技术的理论基础和发展状况,而后利用先进的仿真软件Creator/Vega,建立了某重点型号的飞行环境模型、三维弹体模型和飞行动力模型,在此基础上解算弹道数据并调用API函数编写驱动程序,最终实现了导弹飞行的视景仿真。 相似文献
10.
研究了一种基于SIMBOX实现弹道三维可视化仿真系统的方法。给出了弹道所采用的比例导引法的具体算法,利用3DSMAX软件构建出导弹与目标的三维模型,将其导入到SIMBOX软件的视景系统,采用VC算法对导弹进行具体的机动动作控制,并通过SIMBOX软件对弹道进行了可视化仿真,以动画的方式实现了导弹跟踪及爆炸的三维视景,分别给出了3D和平面的效果图,并分析了比例系数和导弹与目标速度比对弹道的影响,最后将仿真结果与理论推导结果进行了对比。 相似文献
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:2,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
13.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
14.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
15.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
16.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
17.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
18.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
19.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献