航空无刷同步电机起动发电系统电动运行励磁特性

对航空无刷同步电机起动发电系统电动运行的励磁特性进行了理论分析,提出了交直流混合励磁方案,建立了系统的MATLAB/SIMULINK仿真模型。仿真结果表明,主发电机励磁电流平均值随励磁机励磁频率的升高而减小,且主发电机励磁电流脉动率随转速升高有唯一极小值点,该点可作为交直流励磁的切换点。     

励磁系统仿真模型校正技术研究

励磁控制系统作为同步发电机的重要组成部分,主要作用是向同步发电机的定子绕组提供一个可控的直流电流(电压),维持机端电压恒定,满足同步发电机的正常发电需要。通过发电机组控制系统模型,及时校正机组仿真模型,对异常响应进行预警排查,能够有效提高系统运行的稳定性。在MATLAB中搭建了一种以外部仿真机作为励磁调节器的单机无穷大系统仿真模型,模拟励磁系统PID主环异常以及电力系统稳定器(PSS)辅环异常时的输出,与理论值进行对比分析,能够及时确定故障原因和部位,实现故障维修。     

混合励磁无刷爪极发电机的仿真与实验

车载取力发电系统主要采用电励磁无刷爪极电机作为发电机,针对电励磁无刷爪极发电机励磁损耗大、功率密度低的问题,将“混合励磁”的原理引入爪极电机,进行混合励磁无刷爪极发电机的设计与验证。首先,阐述了混合励磁电机的磁场调节原理,并论述了其结构特点和磁通路径。然后,结合三维有限元仿真,对比分析了混合励磁无刷爪极发电机和电励磁无刷爪极发电机的磁场调节特性和全转速范围内的带负载能力。最后,进行了样机的制造和实验验证。实验结果表明,混合励磁无刷爪极发电机具有励磁电流小、功率密度大、低速性能好等优点,为其在车载取力发电系统上的工程应用提供了理论支持和实验依据。     

基于集成电路的航空交流发电机电压调节器设计

介绍了一种基于集成电路的脉冲调宽式航空交流发电机电压调节器的设计方法,给出了具体的硬件电路。利用仿真手段验证了电路设计的正确性,结合三级式航空交流发电机进行了调试,调试结果表明,调压系统具有抗干扰能力强、调压精度高的特点。     

空气涡轮起动机调压装置AMESim建模与仿真

根据空气涡轮起动机ATS(air turbine starter)系统中调压装置(该装置为一个多气动部件组成的压力闭环控制系统)的结构特点及工作原理,通过理论分析建立了其数学模型,采用模块化方法设计了调压装置的AMESim仿真模型.以某型ATS为应用对象,分别在斜坡输入、随机方波输入、阶跃输入及正弦输入下进行系统输出压力仿真.结果显示在不同输入下的压力输出基本恒定,典型工作状态仿真数据与试验数据比较,误差小于3%,表明建模方法是正确的,所建模型可满足工程要求.      

移15°双十二相隐极同步整流发电机数学模型的研究

分别在abc坐标系和dq0坐标系下建立了移15°双十二相隐极同步整流发电机的基本数学方程,推导了电机电压、磁链、输出功率、电磁转矩和转子运动方程。在MATLAB/Simulink中建立了移15°双十二相隐极同步整流发电机的仿真模型。对两路输出进行了不平衡负载仿真和试验。仿真与试验结果相比基本一致,验证了移15°双十二相隐极同步整流发电机数学模型的正确性。这为双十二相同步整流发电机运行性能和励磁控制系统的研究奠定了基础。     

对AVR403型电压调节器的分析

当同步发电机输出电流大小与功率因数改变时,其电枢反应与内阻抗压降将改变,则发电机输出电压也将改变。为使发电机输出电压保持额定值,通常都有自动电压调节器与发电机配套工作。本文较详细地分析了MD-80飞机使用的AVR403型电压调节器各部分电路的工作原理,以及整机调压的工作过程,并阐述了该调压器的特点。     

飞机直流发电机晶体管调压器设计

本文运用以发电机输出电压的变化来控制发电机激磁电压占空比的变化,籍以改变平均激磁电流,达到调整其输出电压之原理,以现设计的由电压敏感电路、单结晶体管三角波发生器、比较器以及功率放大器所组成的晶体管调压器为例,阐述了晶体管调压器的设计方法。文中主要介绍了调压系统数学模型的建立方法,根据对调压系统性能指标的要求,对系统进行综合校正,以及校正装置的设计等。系统实验表明,用此种方法设计的调压器可以获得比较满意的结果。     

同步发电机励磁功率单元中可控整流桥的故障工况研究

分析了三相全控桥式整流电路的各种故障工况,得出故障下触发角与输出励磁电压之间的定量关系,并提出了相应的解决措施。通过对MATLAB/Simulink搭建的同步发电机励磁功率单元模型进行仿真,结果表明,所提措施能有效减轻故障对系统的不利影响,在脉冲丢失时,可以为备用设备切换赢得时间;晶闸管发生故障时,有利于调控发电机平稳退出运行以避免产生稳定性问题。     

基于电力综合集成的多绕组双流发电机技术分析

为解决采用传统发电机的移动电站输出电源种类单一,而采用多台发电机又会造成底盘过载影响机动性的问题,文章基于电力综合集成技术,分析研究实现发电机的双流发电的关键技术,突破发电机多绕组发电及励磁解耦等难题,减小了电机体积、降低了电机重量,有利于移动电站的多功能化与小型化设计。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.