A small mission for in situ exploration of a primitive binary near-Earth asteroid

We present a concept for a challenging in situ science mission to a primitive, binary near-Earth asteroid. A sub-400-kg spacecraft would use solar electric propulsion to rendezvous with the C-class binary asteroid (175706) 1996 FG3. A campaign of remote observations of both worlds would be followed by landing on the ∼1 km diameter primary to perform in situ measurements. The total available payload mass would be around 34 kg, allowing a wide range of measurement objectives to be addressed. This mission arose during 2004 from the activities of the ad-hoc Small Bodies Group of the DLR-led Planetary Lander Initiative. Although the particular mission scenario proposed here was not studied further per se, the experience was carried over to subsequent European asteroid mission studies, including first LEONARD and now the Marco Polo near-Earth asteroid sample return proposal for ESA’s Cosmic Vision programme. This paper may thus be of interest as much for insight into the life cycle of mission proposals as for the concept itself.     

Response of the mid-latitude D-region ionosphere to the total solar eclipse of 22 July 2009 studied using VLF signals in South Korean peninsula

In this paper, we analyze VLF signals received at Busan to study the the D-region changes linked with the solar eclipse event of 22 July 2009 for very short (∼390 km) transmitter–receiver great circle path (TRGCP) during local noon time 00:36–03:13 UT (09:36–12:13 KST). The eclipse crossed south of Busan with a maximum obscuration of ∼84%. Observations clearly show a reduction of ∼6.2 dB in the VLF signal strength at the time of maximum solar obscuration (84% at 01:53 UT) as compared to those observed on the control days. Estimated values of change in Wait ionospheric parameters: reflection height (h′) in km and inverse scale height parameter (β) in km⁻¹ from Long Wave Propagation Capability (LWPC) model during the maximum eclipse phase as compared to unperturbed ionosphere are 7 km and 0.055 km⁻¹, respectively. Moreover, the D-region electron density estimated from model computation shows 95% depletion in electron density at the height of ∼71 km. The reflection height is found to increase by ∼7 km in the D-region during the eclipse as compared to those on the control days, implying a depletion in the Lyman-α flux by a factor of ∼7. The present observations are discussed in the light of current understanding on the solar eclipse induced D-region dynamics.     

Temperature comparison between CHAMP radio occultation and TIMED/SABER measurements in the lower stratosphere

Global Positioning System (GPS) receiver on the CHAllenging Mini-satellite Payload (CHAMP) and the Sounding of the Atmosphere using Broadband Emission Radiometry (SABER) instrument, one of four on board the TIMED satellite, provide middle atmosphere temperature profiles by Radio Occultation (RO) and limb viewing infrared emission measurements, respectively. These temperature profiles retrieved by two different techniques in the stratosphere are compared with each other using more than 1300 correlative profiles in March, September and December 2005. The over-all mean differences averaged over 15 and 35 km are approximately −2 K and standard deviation is less than 3 K. Below 20 km of altitude, relatively small mean temperature differences ∼1 K are observed in wide latitudinal range except for June (during the SABER nighttime observation). In the middle to low latitudes, between 30°S and 30°N, the temperature difference increases with height from ∼0–1 K at 15 km, to ∼−4 K at 35 km of altitude. Large temperature differences about −4 to −6 K are observed between 60°S and 30°N and 31–35 km of altitude for all months and between 0° and 30°N below 16 km during June (nighttime).     

GPS-based sea level measurements to help the characterization of land contamination in coastal areas

The Corsica site has been established in 1996 to perform altimeter calibration on TOPEX/Poseidon and then on its successors Jason-1 and Jason-2. The first chosen location was under the #85 ground track that overflight the Senetosa Cape. In 2005, it was decided to develop another location close to Ajaccio, to be able to perform the calibration of Envisat and in a next future of SARAL/AltiKa that will flight over the same ground tracks. Equipped with various instruments (tide gauges, permanent GPS, GPS buoy, weather station…) the Corsica calibration site is able to quantify the altimeter Sea Surface Height bias but also to give an input on the origin of this bias (range, corrections, orbits, …). Due to the size of Corsica (not a tiny island), the altimeter measurement system (range and corrections) can be contaminated by land. The aim of this paper is to evaluate this land contamination by using GPS measurements from a fixed receiver on land and from another receiver onboard a life buoy. Concerning the altimeter land contamination, we have quantify that this effect can reach 8 mm/km and then affects the Sea Surface Height bias values already published in the framework of the Corsica calibration site by 5–8 mm for TOPEX and Jason missions. On the other hand, the radiometer measurements (wet troposphere correction) are also sensitive to land and we have been able to quantify the level of improvement of a dedicated coastal algorithm that reconciles our results with those coming from other calibration sites. Finally, we have also shown that the standard deviation of the GPS buoy sea level measurements is highly correlated (∼87%) with the Significant Wave Height derived from the altimeters and can be used to validate such parameter.     

Response of low latitude D-region ionosphere to the total solar eclipse of 22 July 2009 deduced from ELF/VLF analysis

Response of the D-region of the ionosphere to the total solar eclipse of 22 July 2009 at low latitude, Varanasi (Geog. lat., 25.27° N; Geog. long., 82.98° E; Geomag. lat. = 14° 55’ N) was investigated using ELF/VLF radio signal. Tweeks, a naturally occurring VLF signal and radio signals from various VLF navigational transmitters are first time used simultaneously to study the effect of total solar eclipse (TSE). Tweeks occurrence is a nighttime phenomena but the obscuration of solar disc during TSE in early morning leads to tweek occurrence. The changes in D-region ionospheric VLF reflection heights (h) and electron density (n_e: 22.6–24.6 cm⁻³) during eclipse have been estimated from tweek analysis. The reflection height increased from ∼89 km from the first occurrence of tweek to about ∼93 km at the totality and then decreased to ∼88 km at the end of the eclipse, suggesting significant increase in tweek reflection height of about 5.5 km during the eclipse. The reflection heights at the time of totality during TSE are found to be less by 2–3 km as compared to the usual nighttime tweek reflection heights. This is due to partial nighttime condition created by TSE. A significant increase of 3 dB in the strength of the amplitude of VLF signal of 22.2 kHz transmitted from JJI-Japan is observed around the time of the total solar eclipse (TSE) as compared to a normal day. The modeled electron density height profile of the lower ionosphere depicts linear variation in the electron density with respect to solar radiation as observed by tweek analysis also. These low latitude ionospheric perturbations on the eclipse day are discussed and compared with other normal days.     

Mesospheric doppler wind measurements from Aura Microwave Limb Sounder (MLS)

This paper describes a microwave limb technique for measuring Doppler wind in the Earth’s mesosphere. The research algorithm has been applied to Aura Microwave Limb Sounder (MLS) 118.75 GHz measurements where the O₂ Zeeman lines are resolved by a digital autocorrelation spectrometer. A precision of ∼17 m/s for the line-of-sight (LOS) wind is achieved at 80–92 km, which corresponds to radiometric noise during 1/6 s integration time. The LOS winds from Aura MLS are mostly in the meridional direction at low- and mid-latitudes with vertical resolution of ∼8 km. This microwave Doppler technique has potential to obtain useful winds down to ∼40 km of the Earth’s atmosphere if measurements from other MLS frequencies (near H₂O, O₃, and CO lines) are used. Initial analyses show that the MLS winds from the 118.75 GHz measurements agree well with the TIDI (Thermosphere Ionosphere Mesosphere Energetics and Dynamics Doppler Interferometer) winds for the perturbations induced by a strong quasi 2-day wave (QTDW) in January 2005. Time series of MLS winds reveal many interesting climatological and planetary wave features, including the diurnal, semidiurnal tides, and the QTDW. Interactions between the tides and the QTDW are clearly evident, indicating possible large tidal structural changes after the QTDW events dissipate.     

An alternative Shell inversion technique - Analysis and validation based on COSMIC and ionosonde data

Multi-channel Global Positioning System (GPS) carrier phase signals, received by the six low Earth orbiting (LEO) satellites from the Constellation Observing System for Meteorology, Ionosphere, and Climate (COSMIC) program, were used to undertake active limb sounding of the Earth’s atmosphere and ionosphere via radio occultation. In the ionospheric radio occultation (IRO) data processing, the standard Shell inversion technique (SIT), transformed from the traditional Abel inversion technique (AIT), is widely used, and can retrieve good electron density profiles. In this paper, an alternative SIT method is proposed. The comparison between different inversion techniques will be discussed, taking advantage of the availability of COSMIC datasets. Moreover, the occultation results obtained from the SIT and alternative SIT at 500 km and 800 km, are compared with ionosonde measurements. The electron densities from the alternative SIT show excellent consistency to those from the SIT, with strong correlations over 0.996 and 0.999 at altitudes of 500 km and 800 km, respectively, and the peak electron densities (N_mF₂) from the alternative SIT are equivalent to the SIT, with 0.839 vs. 0.844, and 0.907 vs. 0.909 correlation coefficients when comparing to those by the ionosondes. These results show that: (1) the N_mF₂ and h_mF₂ retrieved from the SIT and alternative SIT are highly consistent, and in a good agreement with those measured by ionosondes, (2) no matter which inversion technique is used, the occultation results at the higher orbits (∼800 km) are better than those at the lower orbits (∼500 km).     

High vertical resolution water vapour profiles in the upper troposphere and lower stratosphere retrieved from MAESTRO solar occultation spectra

An algorithm has been developed that retrieves water vapour profiles in the upper troposphere and lower stratosphere from optical depth spectra obtained by the Measurements of Aerosol Extinction in the Stratosphere and Troposphere Retrieved by Occultation (MAESTRO) instrument onboard the SCISAT satellite as part of the Atmospheric Chemistry Experiment (ACE) mission. The retrieval relies on ro-vibrational absorption of solar radiation by water vapour in the 926–970 nm range. During the iterative inversion process, the optical depth spectra are simulated at the spectral resolution and sampling frequency of MAESTRO using the correlated-k approximation. The Chahine inversion updates the water vapour volume mixing ratio (VMR), adjusting all retrieval layers simultaneously, to match the observed differential optical depth due to absorption by water vapour and ozone at each tangent height. This approach accounts for significant line saturation effects. Profiles are typically obtained from ∼22 km down to the cloud tops or to 5 km, with relative precision as small as 3% in the troposphere. In the lower stratosphere, the precision on water vapour VMR is ∼1.3 μmol/mol in an individual retrieval layer (∼1 km thick). The spectral capability of MAESTRO allows for the clear separation of extinction due to water vapour and aerosol, and for the fitting quality to be quantified and used to determine an altitude-dependent convergence criterion for the retrieval. In the middle troposphere, interhemispheric differences in water vapour VMR are driven by oceanic evaporation whereas in the upper troposphere, deep convection dominates and a strong seasonal cycle is observed at high latitudes.     

Altimetry,bathymetry and geoid variations at the Gavdos permanent Cal/Val facility

The aim of this work has been to examine the relationship of steep bathymetry in the coastal areas around the permanent Cal/Val facility of Gavdos, and their influence on the produced calibration values for the Jason-2 satellite altimeter. The paper describes how changes in seafloor topography (from 200 to 3500 m depth over a distance of 10 km) are reflected on the determined altimeter parameters using different reference surfaces for satellite calibration. Finally, it describes the relation between these parameter trends and the region’s local characteristics.     

A synchrotron-based facility for the in-situ location,chemical and mineralogical characterization of ∼10 μm particles captured in aerogel

NASA’s Stardust mission collected dust from the coma of Comet Wild-2 on January 2nd, 2004, by direct capture into aerogel cells that flew through the dust coma at ∼6 km/s. Stardust collected several hundred comet particles >10 μm in size. These comet samples were delivered to Earth on January 15th, 2006. We developed a facility at the National Synchrotron Light Source at Brookhaven National Laboratory (Upton, NY, USA) for the in-situ characterization of ∼10 μm particles collected in aerogel. These analytical instruments allow us to perform extensive chemical, mineralogical, and size-frequency characterization of particles captured in aerogel. These analyses are conducted without any invasive extraction, minimizing the possibility of contamination or particle loss during preparation. This facility was used to determine the chemical composition, the oxidation state, the mineralogy and to provide an indication of the grain size of the Wild-2 particles before they were removed from the aerogel. This information provides a catalog of particle types, allowing a more reasoned allocation of the particles to subsequent investigators based on a relatively detailed knowledge of the chemical composition and mineralogy of each particle. These measurements allowed a comparison of the chemical and mineralogical properties of the Wild-2 particles with other types of extraterrestrial materials, including interplanetary dust particles and meteorites. The success of in-situ analysis for Wild 2 particles demonstrates that synchrotron-based facilities will be important for the analysis of particles collected in aerogel on future earth-orbiting satellites and spacecraft.     

Vertical wavenumber spectra of atmospheric ozone measured from ozonesonde observations

Vertical profiles of ozone have been measured at balloon altitudes. Our purpose is to examine the character of vertical wavenumber spectra of ozone fluctuations, to assess the possible roles of gravity wave field in ozone fluctuations, and to determine dominant vertical wavelengths of ozone spectra. Vertical wavenumber spectra of 12 ozone fluctuations obtained during June–August 2003 are presented. Results indicate that mean spectral slopes in the wavenumber range from 4.69 × 10⁻⁴ to 2.50 × 10⁻³ cyc/m are about −2.91 in the troposphere and −2.87 in the lower stratosphere, which is close to the slope of −3 predicted by current gravity wave saturation models. The consistency of the observed spectral slopes with the value of −3 predicted by current gravity wave saturation models suggests that the observed ozone fluctuations are due primarily to atmospheric gravity waves. At m = 1/(1000 m) the mean spectral amplitude is over 30 times larger in the lower stratosphere than in the troposphere. Mean vertical wavenumber spectra in area-preserving form reveal dominant vertical wavelengths of ∼2.6 km in the troposphere and ∼2.7 km in the lower stratosphere, which is consistent with the values varying between 1.5 and 3.0 km estimated from the velocity field and temperature field at these heights.     

Landforms of Europa and selection of landing sites

Three major features make Europa a unique scientific target for a lander-oriented interplanetary mission: (1) the knowledge of the composition of the surface of Europa is limited to interpretations of the spectral data, (2) a lander could provide unique new information about outer parts of the solar system, and (3) Europa may have a subsurface ocean that potentially may harbor life, the traces of which may occur on the surface and could be sampled directly by a lander. These characteristics of Europa bring the requirement of safe landing to the highest priority level because any successful landing on the surface of this moon will yield scientific results of fundamental importance. The safety requirements include four major components. (1) A landing site should preferentially be on the anti-Jovian hemisphere of Europa in order to facilitate the orbital maneuvers of the spacecraft. (2) A landing site should be on the leading hemisphere of Europa in order to extend the lifetime of a lander and sample pristine material of the planet. (3) Images with the highest possible resolution must be available for the selection of landing sites. (4) The terrain for landing must have morphology (relief) that minimizes the risk of landing and represents a target that is important from a scientific point of view. These components severely restrict the selection of regions for landing on the surface of Europa. After the photogeologic analysis of all Galileo images with a resolution of better than about 70 m/pixel taken for the leading hemisphere of Europa, we propose one primary and two secondary (backup) landing sites. The primary site (51.8°S, 177.2°W) is within a pull-apart zone affected by a small chaos. The first backup site (68.1°S, 196.7°W) is also inside of a pull-apart zone and is covered by images of the lower resolution (51.4 m/pixel). The second backup site (2.4°N, 181.1°W) is imaged by relatively low-resolution images (∼70 m/pixel) and corresponds to a cluster of small patches of dark and probably smooth plains that may represent landing targets of the highest scientific priority from the scientific point of view. The lack of the high-resolution images for this region prevents, however, its selection as the primary landing target.     

Inter-agency comparison of TanDEM-X baseline solutions

TanDEM-X (TerraSAR-X add-on for Digital Elevation Measurement) is the first Synthetic Aperture Radar (SAR) mission using close formation flying for bistatic SAR interferometry. The primary goal of the mission is to generate a global digital elevation model (DEM) with 2 m height precision and 10 m ground resolution from the configurable SAR interferometer with space baselines of a few hundred meters. As a key mission requirement for the interferometric SAR processing, the relative position, or baseline vector, of the two satellites must be determined with an accuracy of 1 mm (1D RMS) from GPS measurements collected by the onboard receivers. The operational baseline products for the TanDEM-X mission are routinely generated by the German Research Center for Geosciences (GFZ) and the German Space Operations Center (DLR/GSOC) using different software packages (EPOS/BSW, GHOST) and analysis strategies. For a further independent performance assessment, TanDEM-X baseline solutions are generated at the Astronomical Institute of the University of Bern (AIUB) on a best effort basis using the Bernese Software (BSW).     

Laboratory calibration measurements of a piezoelectric lead zirconate titanate cosmic dust detector at low velocities

A cosmic dust monitor for use onboard a spacecraft is currently being developed using a piezoelectric lead zirconate titanate element (PZT). Its characteristics of the PZT sensor is studied by ground-based laboratory impact experiments using hypervelocity particles supplied by a Van de Graaff accelerator. The output signals obtained from the sensor just after the impact appeared to have a waveform that was explicitly related to the particle’s impact velocity. For velocities less than ∼6 km/s, the signal showed an oscillation pattern and the amplitude was proportional to the momentum of the impacting particle. For higher velocities, the signal gradually changed to a single waveform. The rise time of this single waveform was proportional to the particle’s velocity for velocities above ∼6 km/s. The present paper reports on results for the low velocity case and especially discusses the effect of an outer coating of the sensor with a paint, which is used to reduce heating by solar radiation.     

Regional in situ validation of satellite altimeters: Calibration and cross-calibration results at the Corsican sites

The in situ validation of the satellite altimeter sea surface heights is generally performed either at a few local points directly flown over by the satellites or using the global tide gauge network. A regional in situ calibration method was developed by NOVELTIS in order to monitor the altimeter data quality in a perimeter of several hundred kilometres around a given in situ calibration site. The primary advantage of this technique is its applicability not only for missions flying over dedicated sites but also for missions on interleaved or non repetitive orbits. This article presents the altimeter bias estimates obtained with this method at the Corsican calibration site, for the Jason-1 mission on its nominal and interleaved orbits as well as for the Jason-2 and Envisat missions. The various regional bias estimates (8.2 cm and 7.4 cm for Jason-1 respectively on the nominal and interleaved orbits in Senetosa, 16.4 cm for Jason-2 in Senetosa and 47.0 cm for Envisat in Ajaccio, with an accuracy between 2.5 cm and 4 cm depending on the mission) are compared with the results obtained by the other in situ calibration teams. This comparison demonstrates the coherency at the centimetre level, the stability and the generic character of the method, which would also be of benefit to the new and future altimeter missions such as Cryosat-2, SARAL/AltiKa, Sentinel-3, Jason-3, Jason-CS.     

Global structure,seasonal and interannual variability of the eastward propagating tides seen in the SABER/TIMED temperatures (2002–2007)

The present paper is focused on the global spatial (altitude and latitude) structure, seasonal and interannual variability of the most stable in amplitude and phase eastward propagating diurnal and semidiurnal tides with zonal wavenumbers 2 and 3 derived from the SABER/TIMED temperatures for full 6 years (January 2002–December 2007). The tidal results are obtained by an analysis method where the tides (migrating and nonmigrating) and the planetary waves (zonally travelling, zonally symmetric and stationary) are simultaneously extracted from the satellite data. It has been found that the structures of the eastward propagating diurnal tides with zonal wavenumbers 3 and 2 change from antisymmetric with respect to the equator below ∼85 km height, to more symmetric above ∼95 km. The seasonal behavior of the DE3 is dominated by annual variation with maximum in August–September reaching average (2002–2007) amplitude of ∼15 K, while that of the DE2 by semiannual variation with solstice maxima and with average amplitude of ∼8 K. These tides revealed some interannual variability with a period of quasi-2 years. The seasonal behavior of the eastward propagating semidiurnal tide with zonal wavenumber 2 in the southern hemisphere (SH) is dominated by annual variation with maximum in the austral summer (November–January) while that in the northern hemisphere (NH) by semiannual variation with equinoctial maxima. The SE2 maximizes near 115 km height and at latitude of ∼30° reaching an average amplitude of ∼6 K. The seasonal behavior of the eastward propagating semidiurnal tide with zonal wavenumber 3 in both hemispheres indicates a main maximum during June solstice and a secondary one during December solstice. The tide maximizes near 110–115 km height and at a latitude of ∼30° reaching an average amplitude of ∼4.8 K in the SH and ∼4 K in the NH. The tidal structures of the two eastward propagating semidiurnal tides are predominantly antisymmetric about the equator.     

Electrostatic gravity gradiometer design for the future mission

Satellite gravity gradiometry has been applied in GOCE mission to obtain higher harmonics of the Earth’s gravity mapping. In-orbit results showed that the precision of GOCE gradiometry achieved a level of 10–20 mE/Hz^1/2 in the bandwidth of 38–100 mHz, and the major error source came from the intrinsic noise of the core sensor electrostatic accelerometer. Two schemes for improving sensitivity of such accelerometer are presented by optimizing the parameters to reduce the dynamic range and choosing the heavier proof mass to suppress the thermal noise limited by the discharging gold wire. As a result, an accelerometer with a better resolution of 6.6×$6.6\times$10⁻¹³ m/s²/Hz^1/2 could be developed, and then a precision of 3 mE/Hz^1/2, corresponding to a spatial resolution of about 78 km half wavelength, is achievable for the future satellite gradiometric mission.     

Propagation of normal and faster CMEs in the interplanetary medium

We have analyzed 101 Coronal Mass Ejection (CME) events and their associated interplanetary CMEs (ICMEs) and interplanetary (IP) shocks observed during the period 1997–2005 from the list given by Mujiber Rahman et al. (2012). The aim of the present work is to correlate the interplanetary parameters such as, the speeds of IP shocks and ICMEs, CME transit time and their relation with CME parameters near the Sun. Mainly, a group of 10 faster CME events (V_INT > 2200 km/s) are compared with a list of 91 normal events of Manoharan et al. (2004). From the distribution diagrams of CME, ICME and IP shock speeds, we note that a large number of events tends to narrow towards the ambient (i.e., background) solar wind speed (∼500 km/s) in agreement with the literature. Also, we found that the IP shock speed and the average ICME speed measured at 1 AU are well correlated. In addition, the IP shock speed is found to be slightly higher than the ICME speed. While the normal events show CME travel time in the range of ∼40–80 h with a mean value of 65 h, the faster events have lower transit time with a mean value of 40 h. The effect of solar wind drag is studied using the correlation of CME acceleration with interplanetary (IP) acceleration and with other parameters of ICMEs. While the mean acceleration values of normal and faster CMEs in the LASCO FOV are 1 m/s², 18 m/s², they are −1.5 m/s² and −14 m/s² in the interplanetary medium, respectively. The relation between CME speed and IP acceleration for normal and faster events are found to agree with that of  and  except slight deviations for the faster events. It is also seen that the faster events with less travel time face higher negative acceleration (>−10 m/s²) in the interplanetary medium up to 1 AU.     

Photon counting detector for space debris laser tracking and lunar laser ranging

We are reporting on a design, construction and performance of solid state photon counting detector package which has been designed for laser tracking of space debris. The detector has been optimized for top photon detection efficiency and detection delay stability. The active area of the commercially available avalanche photodiode manufactured on Si (SAP500 supplied by Laser Components, Inc.) is circular with a diameter of 500 μm. The newly designed control circuit enables to operate the detection sensor at a broad range of biases 5–50 V above its breakdown voltage of 125 V. This permits to select a right trade-off between photon detection efficiency, timing resolution and dark count rate. The photon detection efficiency exceeds 70% at the wavelength of 532 nm. This is the highest photon detection efficiency ever reported for such a device. The timing properties of the detector have been investigated in detail. The timing resolution is better than 80 ps r.m.s, the detection delay is stable within units of picoseconds over several hours of operation. The detection delay stability in a sense of time deviation of 800 fs has been achieved. The temperature change of the detection delay is 0.5 ps/K. The detector has been tested as an echo signal detector in laser tracking of space debris at the satellite laser station in Graz, Austria. Its application in lunar laser ranging is under consideration by several laser stations.     

A new approach to solar wind monitoring

The monitoring of solar wind parameters is a key problem of the space weather program. We are presenting a new solution of plasma parameter determination suitable for small and fast solar wind monitors. The first version will be launched during the SPECTR-R project into a highly elongated orbit with apogee ∼350,000 km. The method is based on simultaneous measurements of the total ion flux and ion integral energy spectrum by six identical Faraday cups. Three of them are dedicated to determination of the ion flow direction, the other three (equipped with control grids supplied by a retarding potential) are used for determination of the density, temperature, and speed of the plasma flow. The version under development is primarily designed for the measurements in the solar wind and tail magnetosheath, thus for velocities range from 270 to 750 km/s, temperatures from 1 to 30 eV, and densities up to 200 cm⁻³. However, the instrument design can be simply modified for measurements in other regions with a substantial portion of low-energy plasma as a subsolar magnetosheath, cusp or low-latitude boundary layer. Testing of the engineering model shows that the proposed method can provide reliable plasma parameters with a high time resolution (up to 8 Hz). The paper presents not only the method and its technical realization but it documents all advantages and peculiarities of the suggested approach.