Correlation between horizontal and vertical monopulse measurements

Many radar systems use the monopulse ratio to extract angle of arrival (AOA) measurements in both azimuth and elevation angles. The accuracies of each such measurement are reasonably well known: each measurement is, conditioned on the sum-signal return, Gaussian-distributed with calculable bias (relative to the true AOA), and variance. However, we note that the two monopulse ratios are functions of basic radar measurements that are not entirely independent, specifically in that the sum signal is common to both. The effect of this is that the monopulse ratios are dependent, and a simple explicit expression is given for their correlation; this is of considerable interest when the measurements are supplied to a tracking algorithm that requires a measurement covariance matrix. The system performance improvement when this is taken into account is quantified: while it makes little difference for a tracking radar with small pointing errors, there are more substantial gains when a target is allowed to stray within the beam, as with a rotating (track-while-scan) radar or when a single radar dwell interrogates two or more targets at different ranges. But in any case, the correct covariance expression is so simple that there is little reason not to use it. We additionally derive the Cramer-Rao lower bound (CRLB) on joint azimuth/elevation angle estimation and discover that it differs only slightly from the covariance matrix corresponding to the individual monopulse ratios. Hence, using the individual monopulse ratios and their simple joint accuracy expression is an adequate and quick approximation of the optimal maximum likelihood procedure for single resolved targets.     

基于归一化互相关的系统误差配准算法

雷达组网中由于系统误差存在,航迹不能正确关联,因而无法进行有效的误差配准。为了解决这一问题,理论分析了系统误差对目标航迹的影响并将该影响表示为目标航迹的旋转和平移量,结合图像信号时频域特性,提出了一种基于归一化互相关的误差配准算法。该算法采用归一化互相关来估计和补偿组网雷达目标航迹到融合中心航迹的相对旋转参数和平移参数,从而为后面的系统误差配准提供可靠的航迹关联数据。     

Calibration of complex polarimetric SAR imagery using backscattercorrelations

A technique for calibration of multipolarization synthetic-aperture radar (SAR) imagery is described. If scatterer reciprocity and lack of correlation between co- and cross-polarized radar echoes (for azimuthally symmetric distributed targets) are assumed, the effects of signal leakage between the radar data channels can be removed without the use of known ground targets. If known targets are available, all data channels can be calibrated relative to one another and radiometrically as well. The method is verified with simulation and application to airborne SAR data     

HRR Detector for Slow-Moving Targets in Sea Clutter

The radar detection of targets in the presence of sea clutter has historically relied upon the radial velocity of targets with respect to the radar platform either by exploiting the relative target Dopplers (for targets with sufficient radial velocity) or by discerning the paths targets traverse from scan to scan. For targets with little to no radial velocity component, though, it can become quite difficult to differentiate targets from the surrounding sea clutter. This paper addresses the detection of slow-moving targets in sea clutter using a high resolution radar (HRR) such that the target has perceptible extent in range. Under the assumption of completely random sea clutter spikes based on an epsiv-contaminated mixture model with the signal and clutter powers known, optimal detection performance results from using the likelihood ratio test (LRT). However, for realistic sea clutter, the clutter spikes tend to be a localized phenomenon. Based upon observations from real radar data measurements, a heuristic approach exploiting a salient aspect of the idealized LRT is developed which is shown to perform well when applied to real measured sea clutter.     

Tracker and signal processing for the benchmark problem with unresolved targets

Radar signal processing is particularly important in tracking closely spaced targets and targets in the presence of sea-surface-induced multipath. Closely spaced targets can produce unresolved measurements when they occupy the same range cell of the radar. These issues are the salient features of the benchmark problem for tracking unresolved targets combined with radar management, for which this paper presents the only complete solution to date. In this paper a modified version of a recently developed maximum likelihood (ML) angle estimator, which can produce two measurements from a single (unresolved) detection, is presented. A modified generalized likelihood ratio test (GLRT) is also described to detect the presence of two unresolved targets. Sea-surface-induced multipath can produce a severe bias in the elevation angle measurement when the conventional monopulse ratio angle extractor method is used. A modified version of a recently developed ML angle extractor, which produces nearly unbiased elevation angle measurements and significantly improves the track accuracy, is presented. Efficient radar resource allocation algorithms for two closely spaced targets and targets flying close to the sea surface are also presented. Finally, the IMMPDAF (interacting multiple model estimator with probabilistic data association filter modules) is used to track these targets. It is found that a two-model IMMPDAF performs better than the three-model version used in the previous benchmark. Also, the IMMPDAF with a coordinated turn model works better than the one using a Wiener process acceleration model. The signal processing and tracking algorithms presented here, operating in a feedback manner, form a comprehensive solution to the most realistic tracking and radar management problem to date.     

Bias compensation and tracking with monopulse radars in the presence of multi path

The problem of tracking targets in the presence of reflections from sea or ground is addressed. Both types of reflections (specular and diffuse) are considered. Specular reflection causes large peak errors followed by an approximately constant bias in the monopulse ratio, while diffuse reflection has random variations which on the average generate a bias in the monopulse ratio. Expressions for the average error (bias) in the monopulse ratio due to specular and diffuse reflections and the corresponding variance in the presence of noise in the radar channels are derived. A maximum maneuver-based filter and a multiple model estimator are used for tracking. Simulation results for five scenarios, typical of sea skimmers, with Swerling III fluctuating radar cross sections (RCSs) indicate the significance and efficiency of the technique developed in this paper-a 65% reduction of the rms error in the target height estimate.     

Target detection trials with a millimeter wave radar system

Unobstructed, large RCS targets, similar radar targets surrounded by moving foliage, and small targets in severe clutter have been used as test cases for two pre-processing algorithms and several threshold levels in an experimental millimeter wave radar system. The rather conventional "six-out-of-eight" pulse radar selection method with binary output has been compared to an algorithm that accepts a target if the pre-defined trigger level is crossed by the average of the eight consecutive pulses. In this case, however, the output is an analog value corresponding to the relative average video amplitude. In terms of plotted video, this process seems to give a slightly better combination of false alarm rate and detection probability. Large targets are easier to detect from foliage clutter with the conventional method.     

Phased array of large reflectors for deep-space communication

In this paper the problem of uplink array calibration for deep-space communication is considered. A phased array of many modest-size reflectors antennas is used to drastically improve the uplink effective isotropic radiated power of a ground station. A radar calibration procedure for the array phase distribution is presented using a number of in-orbit targets. Design of optimal orbit and the number of calibration targets is investigated for providing frequent calibration opportunities needed for compensating array elements phase center movements as the array tracks a spacecraft. Array far-field focusing based on the near-filed in-orbit (low Earth orbit (LEO)) calibration targets is also presented and array gain degradation analysis based on the position error of the array elements and in-orbit targets has been carried out. It is shown that errors in the in-orbit targets positions significantly degrade the far-field array gain while the errors in array elements positions are not very important. Analysis of phase errors caused by thermal noise, system instability, and atmospheric effects show insignificant array gain degradation by these factors     

High Resolution in Azimuth for Radar Targets Moving on a Straight Line

Target classification is sometimes desired together with airspace surveillance. To some extent this is possible by observing the flight track resulting from typical radar plots. A possibility for measuring the lateral variation of the radar cross section for single targets is described in the following. This method assumes a straight unaccelerated flight path, at least for a few seconds, with tangential components. This restriction is mitigated by prevailing straight flight paths and by observation of targets with radar nets, so there is always a tangential component. This method is especially suitable for electronic steerable radar application.     

Monopulse DOA estimation of two unresolved Rayleigh targets

This paper provides for new approaches to the processing of unresolved measurements as two direction-of-arrival (DOA) measurements for tracking closely spaced targets rather than the conventional single DOA measurement of the centroid. The measurements of the two-closely spaced targets are merged when the target echoes are not resolved in angle, range, or radial velocity (i.e., Doppler processing). The conditional Cramer Rao lower bound (CRLB) is developed for the DOA estimation of two unresolved Rayleigh targets using a standard monopulse radar. Then the modified CRLB is used to give insight into the boresight pointing for monopulse DOA estimation of two unresolved targets. Monopulse processing is considered for DOA estimation of two unresolved Rayleigh targets with known or estimated relative radar cross section (RCS). The performance of the DOA estimator is studied via Monte Carlo simulations and compared with the modified CRLB     

Multi-aspect radar target recognition method based on scattering centers and HMMs classifiers

A hidden Markov model (HMM)-based method for recognizing aerial targets according to the sequential high-range-resolution (HRR) radar signature is presented. Its recognition features are the location information of scattering centers extracted from the HRR radar echoes by the relax algorithm. The HMM is used to characterize the spatio-temporal information of a target. Several HMMs are cascaded in a chain to model the variation in the target orientation and used as classifiers. Computer simulations with the inverse synthetic aperture radar (ISAR) data are given to demonstrate that for an open-set recognition, average class-recognition rates of 84.50% and 89.88% are achieved, respectively, under two given conditions.     

地空协同防空目标抗差跟踪算法

针对现有系统误差配准算法以已知系统误差变化模型为前提条件、相应的目标状态估计易受系统误差配准结果影响等不足之处,在机载雷达与地基雷达协同防空预警体系下,对系统误差存在情况下的目标跟踪问题进行了研究,并提出了有效的地空协同防空目标抗差跟踪算法。仿真结果表明所提算法可得到无偏、稳定、有效的目标状态估计,并且相对于系统误差目标状态联合估计算法,所提算法计算量小,对系统误差变化有很强的鲁棒性,可适应实际工程应用中可能出现的异常情况,为后续决策提供稳定有效的目标信息。     

Optimal polarimetric detection of radar target in a slowlyfluctuating environment of clutter

It is shown that in a situation where a radar target is distant enough from the radar and is included in a natural or artificial clutter environment in such a manner that the conventional detection methods fail, it is possible to improve the radar detection performance by using appropriate signal processing on two orthogonal polarization states. A CFAR (constant false alarm rate) polarimetric detection system based on the study of the polarization difference between clutter and target is proposed. Since the polarization state of the clutter echoes fluctuates slowly from cell to cell, an autoregressive model can be applied to the components of the polarization vector to predict the detection thresholds needed to follow the polarization state variation. The detection thresholds are determined to maintain a false alarm probability equal to 10^-6. The presence of a target registers as a significant variation of the estimation error of the polarization vector. Results obtained from measurements of simple and canonical targets with artificial clutter are presented, and these results validate the principle of polarimetric detection     

RFI suppression for ultra wideband radar

An estimate-and-subtract algorithm is presented for the real-time digital suppression of radio frequency interference (RFI) in ultrawideband (UWB) synthetic aperture radar (SAR) systems used for foliage- and ground-penetrating imaging. The algorithm separately processes fixed- and variable-frequency interferers. Excision of estimated targets greatly reduces bias in RFI estimates, thereby reducing target energy loss and sidelobe levels in SAR imagery. Performance is demonstrated on data collected with the Army Research Laboratory's UWB rail SAR.     

Design considerations for a real-time random-noise tracking radar

Random-noise radar has been applied successfully to range measurement, velocity estimation and terrain/target imaging. For applications involving stationary targets, long integration times and process averaging are easily tolerated. In situations where the target or radar platform moves at high speed, the impact of this relative motion on system design should be considered. This work addresses the statistical performance of a generic random-noise radar receiver and examines the inter-relationships between design parameters and performance tradeoffs. Complementing this examination, a random-noise monopulse system is also investigated as a possible architecture for real-time angle estimation. Simulations and numerical illustrations provide the basis of processor design and performance prediction.     

Moving target imaging algorithm for SAR data

A digital processing algorithm for fine-resolution imaging of synthetic aperture radar (SAR) moving targets is described. The targets may have any translational and rotational motion components relative to the data collection platform. The algorithm requires the presence of up to three prominent points in the image of the target; the signals from these points provide estimates of the unknown target motion parameters. Phase compensation and data formatting based on these estimates eliminate motion-induced phase errors. This algorithm has been implemented on a VAX computer and used to process both simulated and real SAR data of moving targets. Results obtained using the simulated data are presented     

Distributed Array Radar

Distributed array radar (DAR) is a concept for efficiently accomplishing surveillance and tracking using coherently internetted mini-radars. They form a long baseline, very thinned array and are capable of very accurate location of targets. This paper describes the DAR concept. Factors involving two-way effective gain patterns for deterministic and random DAR arrays are analyzed and discussed. An analysis of factors affecting signal-to-noise ratio is presented and key technical and performance issues are briefly summarized.     

Analysis of interference effects on monopulse radars

The complete numerical analysis of angle-tracking performance of a coherent amplitude-comparison monopulse radar system in a two-target situation is described. This system, equipped with automatic gain control (AGC) and phase-locked loop (PLL), was originally invented for improving the target-tracking performance in multiple-target situation. The general behavior depends on Doppler separation of the targets relative to the bandwidths of AGC and PLL. The performance of this system has previously been roughly analyzed by using linear approximation for four extreme cases: wideband and narrowband AGC in combination with wideband and narrowband PLL. In this study, the author performs nonlinear analysis of the same system for all bandwidths of AGC and PLL, because Doppler separation varies over a wide range in actual tracker, and therefore it is indispensable to know the total system behavior. A special numerical technique called the Galerkin method is used. As a result of this analysis, the extensive target-tracking performance for all intermediate bandwidths of AGC and PLL has been clarified. The result is useful for actual target tracker design     

某雷达模拟器的目标与杂波信号模拟强度研究

建立了雷达模拟器中目标、地物杂波、海杂波、气象杂波的信号强度计算模型,根据相对运动关系解算出各目标与杂波信号的强度,并按时间流程存储在对应的数据表中,从而信号源将产生相应强度的信号注入雷达模拟台,以便后端雷达模拟台能在雷达威力覆盖范围内准确地显示出目标与杂波强度变化。通过仿真软件在雷达训练模拟器中的功能测试,实现了目标与杂波仿真效果,满足了雷达模拟训练的要求。