民用飞机大侧风验证试飞方法研究

抗侧风作为飞机飞行的一项重要能力,需要通过试飞的方法进行验证,以表明飞机的抗侧风能力满足民用飞机适航规章条款的要求。主要从大侧风的试飞方法、试飞技术、试飞结果处理方法、适航验证等方面进行研究,提供民用飞机的大侧风验证试飞方法和适航符合性方法研究。     

小型民用正常类飞机尾旋特性试飞技术研究

简要介绍了按照CCAR-23部进行合格审定正常类飞机对尾旋试飞的要求,对小型民用飞机尾旋特性试飞方法进行了研究,结合具体型号进行了飞行试验验证,给出了该飞机的尾旋试飞结果。结果证明,该试飞技术适用于小型民用飞机型号合格审定尾旋试飞。     

航空快递

ARJ21-700飞机102架机转场阎良大侧风局方审定试飞落下帷幕2013年4月27日,ARJ21-700飞机102架机进行了大侧风相关科目试飞,飞机于在13时06分在嘉峪关机场起飞,经过5小时30分钟的飞行,于18时36分着陆。     

民机地面最小操纵速度试飞技术研究

基于CCAR-25对于民用飞机地面最小操纵速度(VMCG)的合格审定试飞要求,对地面最小操纵速度试飞技术进行了分析,针对ARJ21-700飞机,从试飞准备、试飞方法、驾驶技术和试飞程序等方面,制定了详细的试飞方案,试飞得到VMCG为107kn。由于VMCG受机场大气影响,因此对其进行数据扩展,得到全包线范围内的VMCG。该试飞技术和数据处理方法可为其他民用飞机的型号合格审定试飞提供参考。     

简讯

ARJ21-700完成大侧风补充试验试飞2011年5月19日11时30分许,ARJ21-700飞机102架机从某外场安全返回中航工业试飞中心,这标志着新支线大侧风补充试验试飞顺利完成     

大型水陆两栖飞机侧风起降的滑流影响分析

大型水陆两栖飞机AG600的动力装置为安装在机翼上的4台同向旋转涡轮螺旋桨发动机,针对1：15缩比模型带动力风洞试验显示的螺旋桨滑流对侧风起降状态的偏航力矩不稳定影响,对全机带动力风洞试验模型进行了大规模并行非定常数值计算,再现了风洞试验现象,通过流动机理分析明确其产生原因主要是左侧滑时右外翼分离和垂尾背鳍涡破裂,这些原因和数值模拟的准确性也为后期的风洞试验所证实。考虑到模型风洞试验中尺度限制造成的低雷诺数和高螺旋桨转速,为保证飞行安全,继续采用该非定常方法对全尺寸飞机真实侧风起降状态进行了详细数值分析和偏航稳定性评估。研究结果显示,在飞行雷诺数和螺旋桨转速下,相同侧风范围内风洞试验显示的流动不稳定因素基本消失,偏航稳定性允许的侧风范围明显增加。本研究实现了四发螺旋桨飞机起降状态横向气动特性的滑流影响非定常数值分析,建立了基于计算流体力学的风洞与飞行雷诺数效应的相互关系,进行了偏航稳定性的虚拟试飞评估,研究成果也为AG600飞机的首飞和飞行试验所验证。     

民用飞机燃油系统负加速度试飞技术研究

一个新型的民用飞机要投入航线使用,必须经过适航合格取证试飞,获得型号合格证、生产许可证和适航证,具备三证才允许走向市场。民用飞机适航取证试飞项目有许多,其中负加速度试飞是民用飞机燃油系统适航取证试验的重要验证项目。民用飞机负加速度试飞在国内尚属首次,具有对机组操纵技术要求高、风险难度大的特点。结合某型民机燃油系统合格审定试飞,研究了民用飞机负加速度的试飞技术,提出了用抛物线试飞方法来完成负加速度试飞任务。主要介绍了负加速度试飞中可能出现问题、试飞前应准备的工作、试飞方法等,并对试验结果进行了分析。     

民用飞机冰污染水平安定面失速试飞技术研究

基于CCAR-25对民用飞机冰污染水平安定面失速的合格审定试飞要求,对冰污染水平安定面失速进行了分析,针对ARJ21-700飞机,分析总结了冰污染水平安定面失速原理、改出方法、与机翼失速的差异、试飞方法和试飞结果分析,对于民用飞机合格审定试飞以及他运输类飞机具有非常重要的意义。     

通用飞机的验证试飞

引言 按照民航"型号合格审定程序",民用飞机的调整试飞在验证试飞前的委员会会议(TCB)核准后,飞机就进入验证试飞阶段,直到完成验证试飞大纲所规定的试飞科目.作为小型民用飞机的通用飞机必须遵循这一程序,本文根据小鹰500飞机的验证试飞实践,阐述通用飞机的验证试飞.     

小型通用民用飞机的失速试飞研究

介绍了小型通用民用飞机的失速试飞依据与要求、试飞方法与驾驶技术、数据处理与分析方法。提出了直接采用发动机慢车状态来确定无动力状态下飞机失速速度的试飞方法，并以小鹰-500飞机为例，给出了用本方法确定零拉力失速速度的符合性验证及失速特性的符合性验证结果。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.