Robust model following control of parallel buck converters

A robust model-following (RMF) control technique for average current mode controlled (ACC) parallel buck dc-dc converters, RMFACC, is presented. RMFACC achieves that the loop gain of the voltage loop is little sensitive to the variation of power stage parameters: number of modules, input voltage, load, and component tolerances. The design of the voltage loop is 'decoupled' from the design of the disturbance rejection transfer functions in an important degree, so that the output impedance and audio susceptibility are greatly reduced without the need of high loop gain crossover frequencies. A comparative study between conventional ACC and RMFACC is shown.     

Design Optimization for a Half-Bridge DC-DC Converter

A nonlinear programming technique using the penalty function method is employed for the minimum weight design of a halfbridge dc-dc buck power converter. The cost-effective computeraided approach provides a minimum weight design down to the details of the component level which concurrently meets all power circuit performance requirements. Important design insights and guidelines are obtained to readily assess 1) the tradeoffs between weight and loss as the switching frequency is increased, 2) the optimum operating frequency range over which the total weight/loss is minimized, 3) the impact of device characteristics on the total weight and loss profile.     

基于加工误差仿真的半球谐振子优化设计

针对半球谐振陀螺谐振子制造过程中存在的加工误差,采用有限元仿真,分析了半球谐振子结构参数、尺寸公差和形位公差变化对其工作模态频率和临近模态频率的影响,研究了半球谐振子形位公差变化对频率裂解和品质因数的影响。通过仿真分析可知,半球谐振子结构参数壁厚、半球中心半径及内倒角半径都会影响模态频率;半球谐振子形位公差中的内外球心距离误差对其工作模态影响较大,中心轴平行误差对频率裂解和品质因数影响较大;半球谐振子壁厚、内倒角半径、小柱半径及内外球心距离误差变化会使工作模态频率与相邻模态间存在干扰。在此基础上,提出了半球谐振子结构参数及形位公差优化设计建议,并通过半球谐振子品质因数Q值和频率裂解测量对该建议进行了验证。     

Current Injected Equivalent Circuit Approach to Modeling Switching DC-DC Converters

A new current injected equivalent circuit approach (CIECA) to modeling switching dc-dc converter power stages is developed, which starts with the current injected approach and results in either a set of equations which completely describe input and out-put properties or an equivalent linear circuit model valid at small signal, low frequency levels. This approach to modeling switching dc-dc converter power stages has the merits but not the demerits of both the electronic equivalent circuit state space average approach and the current injected control type approach, namely, 1) the modeling is very clear and is simple whether the converter operates in continuous or discontinuous inductor conduction modes, 2) the modeling results in an equivalent circuit which is very close to the actual converter, and 3) the equivalent circuit can be used directly in the computer for theoretical predictions like SPICE, etc.     

Low-Frequency Characterization of Switched dc-dc Converters

Averaging techniques are developed to represent buck, boost, and buck-boost types of switched dc-dc converters by approximate continuous models. Simple analytical expressions in terms of the circuit components are derived for the characteristic transient and frequency responses of time-average(continuous) power-stage models for use in designing and understanding the behavior of corresponding switched power stages. Novel conclusions include the dependence of effective circuit component values upon switch duty ratio and the existence of a real positive zero in certain transfer functions. Responses from analog computer simulations of the switched and averaged powerstages agree well and, in turn, confirm the analytic predictions. High-order systems can be analyzed by the averaging technique without a commensurate increase in complexity.     

Battery charger design for the Columbus MTFF power system

A novel pulsewidth-modulated (PWM) dc-dc converter topology is proposed for the battery charge regulator (BCR) of the Columbus Man-Tended Free-Flyer (MTFF) power system. The system is a regulated bus system. Bus voltage control is implemented at the input of the BCR. The use of a conventional buck topology with PWM conductance control at the input results in a second-order behavior. A study of new PWM dc-dc converter topologies has been made to attain a suitable topology. The proposed converter topology is designed and a breadboard including the control loop has been built and tested. The experimental results show that the converter operates according to the design constraints.     

考虑禁飞圆的滑翔式机动弹道与气动特性参数耦合设计

 为获得滑翔式再入飞行器最佳气动与弹道机动性能,针对规避禁飞圆的远程滑翔式再入问题提出了一种机动弹道与气动特性参数耦合设计方法。耦合设计外环以气动特性参数为设计变量,基于抛物阻力极线模型提取最大升阻比和对应升力系数为气动特性参数;耦合设计内环以泛化升力系数和侧倾角为设计变量,获得给定升阻特性下能规避禁飞圆且满足再入走廊要求的滑翔式再入轨迹。耦合设计问题以再入驻点总热流最小为优化目标,以再入走廊、终端位置和速度为约束,求解满足弹道机动要求且目标函数最小的最佳气动特性参数。提出了一种规避禁飞圆的侧向几何制导逻辑用于内环轨迹设计。仿真算例得出禁飞圆半径越大,需要的滑翔式再入飞行器最大升阻比越大,且再入轨迹刚好能绕过禁飞圆。仿真结果验证了耦合设计方法和侧向制导逻辑的有效性,该方法可为飞行器方案设计时的气动布局选型等工作提供参考。     

基于Taguchi方法的转子系统动力学容差设计

提出了基于Taguchi方法的转子系统动力学容差设计理论.从结构的动力响应要求出发,以Taguchi方法为基础,对结构的制造及装配容差进行动力学容差设计,减小结构在制造过程的设计参数不确定和安装工艺不确定影响下其动力响应的波动.该设计过程为:①通过正交试验及方差分析完成参数设计,初步确定符合要求的参数设计值组合;②确定容差设计的初始设计值及初始设计范围,确定目标函数,形成多目标优化问题;③利用遗传算法对多目标优化问题进行解算,得到容差设计结果.对某型双转子航空发动机具有初始不平衡量轮盘的安装工艺进行了容差设计.设计表明:具有初始不平衡量的轮盘在装配时通过控制不平衡量的幅值及相位角差的搭配可有效降低支承振动响应,设计后支承最大振动响应合格率由17.7%提高至97%,验证了该设计理论的可行性.     

Preliminary design and optimization of slotted tube grain for solid rocket motor

In this paper,design and optimization technique of slotted tube grain for solid rocket motors has been discussed.In doing so,the design objectives and constraints have been set,geometric parameters identified,performance prediction parameters calculated,thereafter preliminary designs completed and finally optimal design reached.Geometric model for slotted tube grain configuration has been developed.Average thrust has been taken as the objective function with constraints of burning time,mass of propellant,fixed length and diameter of chamber case.Lumped parameter method has been used for calculating the performance prediction parameters.A set of preliminary designs has been completed and an analysis of these results conducted.Although all the preliminary results fulfill the design requirements in terms of objective function and constraints,however in order to attain the optimal design,Sequential quadratic programming optimization technique has been adopted.As the slotted tube grain geometry is totally dependent upon various independent variables and each of these variables has a bearing on explicit characteristic of grain designing,hence affects of the independent variables on performance parameters have been examined,thus variation laws have been developed.Basing on the variation laws and the analysis of preliminary design results,upper and lower limits have been defined for the independent geometric variables and an initial guess provided for conducting optimization.Results attained exhibits that an optimal result has been attained and the value of objective function has been maximized.All the design constraint limits have also been met while ensuring sound values of volumetric loading fraction,web fraction and neutrality.This methodology of design and optimization of slotted tube grain for solid rocket motors can be used by engineers as a reference guide for actual design and engineering purposes.      

基于系统辨识的框架控制系统设计

为提高框架系统控制性能,采用系统扫频方法对系统实际模型进行扫频辨识。由于加工和安装工艺等原因,框架不同位置处的摩擦力矩差异较大。研究了固定补偿值摩擦力矩补偿算法和变补偿值积分摩擦力矩补偿算法,并重新进行了扫频。根据辨识得到的模型设计了校正网络,提高了系统控制性能。     

航空发动机PI控制参数频域最优整定方法

针对航空发动机高、低压转速和压比的控制回路,研究满足幅值裕度和相角裕度要求的比例-积分(PI)控制参数稳定域确定方法.根据系统在频域的稳定域解析模型,建立考虑PI控制器的系统参数频域稳定域图形.根据典型的动态性能指标和鲁棒性指标定义的优化目标函数,在所得到的控制参数稳定域中寻找到一组最优的PI控制参数.该方法应用于航空发动机高、低压转速和压比回路控制器参数设计中,设计了不同状态下的PI控制器,仿真结果表明,这种整定方法能够使闭环系统满足性能指标和鲁棒性.      

基于FPGA的硅微机械陀螺仪数字化驱动电路研究

为了进一步提高硅微机械陀螺仪的性能,提出了一种基于FPGA数字信号处理来实现控制的数字化驱动电路。该设计方案通过AGC环路稳定了驱动幅度,并用SPLL对相位进行了控制以跟踪谐振频率。两主要环路以FPGA为硬件基础,用软件编程实现,相较模拟驱动电路在实际应用中更具灵活性。实验给出了该电路的驱动幅度和频率漂移曲线,证明了该电路可以较好的实现硅微机械陀螺仪的驱动。     

混合动力汽车ISG用混合永磁同步电机转子研究

设计了一款混合动力汽车集成式起动发电机(ISG),用钕铁硼和铁氧体混合永磁的永磁同步电机(PMSM)。分析了两种永磁体的结构参数对电机磁路的影响规律,推导了钕铁硼和铁氧体并联磁路的约束条件;以铁氧体的不可逆退磁量和电机的基本性能为优化目标,通过场-路结合的方法,确定了钕铁硼和铁氧体的结构参数;并与传统的钕铁硼PMSM在电机性能和永磁体成本等方面进行了比较分析。研究结果表明,所提出的ISG混合永磁电机能有效地减少永磁体材料成本和铁氧体退磁风险,电机性能达到了设计要求。     

An optimal method of posture adjustment in aircraft fuselage joining assembly with engineering constraints

Posture of an aircraft fuselage can be evaluated based on the coordinate values of measure points fixed on the aircraft fuselage in aircraft final assembly. Posture adjustment is carried out by rotation and translation of the aircraft fuselage to make sure that the actual coordinate values of the measure points are coincided with the theoretical ones read from the computer aided design(CAD) model. The point registration method of posture adjustment without considering engineering constraints may cause out-of-tolerance for some engineering constraints. Hence, engineering constraints such as plane symmetry of two points, as well as coplanar and collinear of the multipoint should be considered in the new optimal method of posture adjustment in aircraft fuselage joining assembly. Based on the point registration model, a multi-objective optimization model of posture adjustment considering engineering constraints including collinear, coplanar, and symmetry constraints is established and represented by a uniform vector function. The weights of constraint conditions can be set freely in the optimization model to reflect the importance of the corresponding constraints in aircraft fuselage joining assembly. The rotation and translation parameters of posture adjustment are obtained by the proposed multi-objective optimization algorithm based on the Gauss-Newton method. Results of an example of aircraft fuselage joining assembly show that constraint errors of posture adjustment obtained by the multi-objective optimization model are not out of tolerance for design constraint errors and satisfy the requirement of aircraft fuselage joining assembly.     

基于蒙特-卡罗法的电子电路统计分析仿真

电子电路的统计分析在电子产品批量生产前对产品元器件容差的选取、产品成品率和生产成本预测上有很好的指导意义。蒙特-卡罗分析方法是电子电路常用的统计方法之一,采用计算机模拟的蒙特-卡罗法通过对电子电路的性能统计试验来求得其性能的期望值、标准差等统计参数,并能从进一步求得的直方图上预测该性能处于技术指标允许范围之内的产品合格率。通过统计分析结果可以选取可靠性高、成本低的设计方案,以实现电子电路的优化设计。本文以滤波器为例说明在OrCAD/PSpice9环境下进行电路统计分析的方法和应用。     

Stability analysis of parallel DC-DC converters

We develop analytic methodologies for stability analyses (using nonlinear and linear methodologies) of parallel dc-dc converters (under unsaturated and saturated operating conditions) using their switching model, discrete model (based on nonlinear map), and averaged model. We describe the approach for investigating the behavior of the stable and unstable equilibrium solutions of a parallel dc-dc converter under parametric variations and illustrate the methodology using a load-sharing dc-dc buck converter. For unsaturated operating condition, using bifurcation analysis and Floquet theory, we predict the stability boundary of the nominal solution, determine its postinstability dynamics, and investigate the dependence of the converter dynamics on its initial conditions. Subsequently, we demonstrate the differences in the predictions of the instabilities and instability boundaries using (conventional) linearized averaged (small-signal) and discrete and switching models.     

一种基于参数控制的低轨星载接收机载波跟踪算法CSCD

低轨星座接收机面临大多普勒频移及频繁快速换星等设计约束,对其载波跟踪环路设计提出了较高的动态适应性与跟踪精度要求。针对以上问题,提出了一种基于参数控制的载波跟踪算法。该算法引入环路控制因子参数,将环路滤波器分为牵引和跟踪两阶段。基于理论建模推导环路控制因子的最优参数配置原则,指导实现牵引和跟踪两种状态滤波器的协同配合,在牵引阶段有效引导大多普勒信号快速入锁,在跟踪阶段精确估计载波频移参数,实现基于低轨星载平台的GNSS信号快速准确跟踪。理论与仿真结果均表明基于参数控制的载波跟踪算法能够有效提升环路的动态适应性与跟踪精度,满足低轨星载接收机的设计需求。与传统算法相比,该算法在保证信号跟踪精度的同时,能够将收敛时间缩短78%,且环路设计简单,易于硬件实现。     

Phase-Frequency Detection in Sampled Phase-Locked Frequency Mlultipliers

Phase-locked high-frequency multipliers which do not have powergreedy frequency dividers in the feedback loop, but which do have a sample-and-hold circuit as a phase detector are hard to design, due to conflicting requirements which determine the choice for loop gain and loop bandwidth. A circuit is described that acts as a frequency control if the loop is not locked and as a phase control once the loop can be locked. The loop filter has to be optimized for the locked condition only, and the allowable preset error is more than 80 percent of the sample frequency. The circuit also indicates whether the oscillator frequency is an odd or an even multiple of the sample frequency. Pull-in is at least an order of magnitude faster than with phase control alone.     

Improved Switching Converter Model Using Discrete and Averaging Techniques

The nonlinear modeling and analysis of dc-dc converters has been done by averaging and discrete-sampling techniques. The averaging technique is simple, but inaccurate, as the modulation frequencies approach the theoretical limit of one-half the switching frequency. The discrete technique is accurate even at high frequencies, but is very complex and cumbersome. An improved model is developed by combining the aforementioned techniques. This new model is easy to implement in circuit and state variable forms and is accurate to the theoretical limit.     

某型航空发动机封严篦齿盘异型螺栓孔公差设计分析

为了有效降低孔边应力水平,以某型航空发动机封严篦齿盘5参量单轴对称异型孔为研究对象。针对此类异型孔的公差设计问题,利用蒙特卡洛模拟技术,通过构造异型孔孔边应力状态的响应面函数以对设计参数进行灵敏度分析,确定了需要给定公差的设计变量。讨论了异型孔的重要设计尺寸公差带对孔边应力分布及配合的影响,并参照美制紧固件螺栓通孔设计标准,确定了此类异型孔尺寸公差选取应满足的强度要求及装配等级。