基于零厚度内聚力单元单向碳纤维增强树脂基复合材料微观切削机理研究

为探究碳纤维复合材料(CFRP)微观切削机理,通过有限元法,采用零厚度内聚力单元模拟界面相,碳纤维建模呈圆柱状并随机分布于基体中,以此来真实反应CFRP的微观结构。通过对各组成相设置不同的材料本构、材料失效和演化准则,对4种典型角度(0°、45°、90°、135°)进行直角切削仿真,探究不同纤维角度下单向碳纤维增强树脂基复合材料(UD-CFRP)在切削过程中的微观切削机理。结果表明:不同纤维角度下CFRP的微观破坏形式不同,切削0°CFRP时破坏主要以界面开裂和纤维折断为主,切削45°和90°CFRP时主要是刀具的侵入破坏,切削135°CFRP时则发生纤维的断裂和沿纤维方向的裂纹,纤维断裂点在刀刃下方。最后,通过实验验证了微观模型的准确性。     

纤维方向角对超低温冷却石英纤维复合材料铣削性能的影响

石英增强聚酰亚胺树脂基复合材料是一种非均匀的各向异性材料,其加工性能高度依赖于纤维铺层方向与加工进给方向所成角度,即纤维方向角。本文通过一系列不同纤维方向角的干切削和超低温冷却铣削实验,研究了纤维方向角对表面形貌、表面粗糙度、铣削力及刀具磨损的影响。结果表明:不同纤维方向角,剪应力形式不同,切削断屑形式也不同。纤维方向角为锐角时铣削表面质量均良好,但当纤维方向角增大到90°时,切削表面质量下降,切削力变化幅度增大。相同铣削时间内,在干切削工况下,刀具磨损严重,涂层脱落面积约为测量面积的70%;而在低温切削工况下,涂层未遭到严重破坏,刀具仍处于稳定磨损阶段,刀具耐用度优于干切削工况。     

Evaluation of tool wear and cutting performance considering effects of dynamic nodes movement based on FEM simulation

An accurate estimation of tool wear morphology can provide the opportunity to investigate the influence of tool wear on cutting performance as well as reduce the overall production cost. However, tool wear prediction is still a very challenging research issue. In this paper, a novel method for simulating the actual chip formation and wear evolution thorough the 3D finite element model has been carried out. In order to improve the accuracy of simulation results, the influence of worn tool, stress and temperature distribution on wear rate are considered. Then cutting experiment has been conducted by turning AISI1045 with uncoated carbide tools to validate the accuracy of the proposed model. The comparison between experimental and simulation results show good agreement which proves the ability of the proposed model in forecasting the tool wear. The validated finite element model has been further utilized studying how the worn tool affects the cutting performance including actual cutting rake, stress distribution, cutting force and temperature. The results of this paper not only provide a clear understanding of wear evolution between tool rake face and chip, but also are meaningful to optimize tool design and cutting parameters.     

Surface integrity and fatigue behavior when turning γ-TiAl alloy with optimized PVD-coated carbide inserts

This paper presents a comprehensive investigation on the effects of tool and turning parameters on surface integrity and fatigue behavior in turning c-Ti Al alloy. The wear of inserts surface, cutting forces, and surface roughness were studied to optimize PVD-coated carbide inserts.Surface topography, residual stresses, microhardness, and microstructure were analyzed to characterize the surfaces layer under different turning parameters. Surface integrity and fatigue life tests of c-Ti Al alloy were conducted under turning and turning-polishing processes. The results show that compared to CNMG120412-MF4, CNMG120408-SM is more suitable because it obtained low cutting force, surface roughness, and tool wear. With increasing the cutting speed and depth, the depths of the compressive residual stress layer, hardening layer, and plastic deformation layer increased. For turning and turning-polishing specimens, the compressive residual stress was relaxed by less than 20%–30% after 10~7 cycles. The fatigue life of a turning-polishing specimen with R_a= 0.15 mm has increased 3 times from that of a turning specimen with R_a= 0.43 mm.     

CFRP三维铣削仿真模型的建立及层间损伤分析

碳纤维增强树脂基复合材料(CFRP)具有层间结合强度低、各向异性等特点,切削过程中易产生层间损伤。为了对CFRP铣削加工过程中的层间应力、层间损伤进行研究,建立了复合材料三维铣削仿真模型。该模型在结构上采用等效均质建模,层内单元利用VUMAT子程序建立了三维Hashin起始失效准则以及损伤演化过程模型,层间采用Cohesive单元连接以模拟层间损伤的产生及扩展。通过与实验切削力数值的比较,验证了仿真模型的准确性。利用该模型分析了切削力、层间应力及层间损伤随纤维方向角(0°、45°、90°、135°)的变化规律。结果表明:铣削过程加工损伤主要集中在近工件表面。铣削力、层间应力、层间损伤受纤维方向角的影响,纤维方向角为90°与135°时,轴向铣削力较大,层间应力与层间损伤均随纤维方向角的增加而增大,纤维方向角为135°时,层间应力最大,层间损伤最严重。     

Investigation on surface integrity of electron beam melted Ti-6Al-4 V by precision grinding and electropolishing

Electron beam melting (EBM), as an excellent Additive Manufacturing (AM) technology, enables the printing of Ti-6Al-4 V alloy for a wide range of applications such as aerospace and biomechanical industries. It improves functionality and integrity of components and negates complexities in assembly processes. However, due to the poor surface and sub-surface integrity represented by the rough surface finish and low dimensional accuracy, achieving a favorable surface condition is quite challenging. Therefore, post processing becomes essential for these electron beam melted (EBM-ed) Ti-6Al-4 V alloys. Being the most common technique to improve such parts, milling of Ti-6Al-4 V alloy is very challenging and resulting tool wear issues, due to its unique material properties. Thus, this paper presents a comprehensive study on the surface integrity of EBM-ed Ti-6Al-4 V parts processed by precision grinding and electropolishing, aiming to qualitatively and quantitatively clarify the interrelation between process parameters and processed surface quality. The surface and subsurface characteristics such as profile accuracy, surface roughness, microstructure, defective layer and residual stress before and after post processing were compared and evaluated. The results show that by precision grinding, the profile accuracy was improved from over 300 µm PV to 7 µm PV, while surface roughness (R_a) was reduced from 30 µm to about 2 µm. The layer with partially melt particles was removed, but introduced a deformed subsurface layer with more residual stress. Then by applying electropolishing, the residual stress was released and the deformed layer was removed. In addition, R_a was further reduced to 0.65 µm. The research can serve as a reference for the integration of post machining processes with AM.     

Elliptical vibration cutting of large-size thin-walled curved surface parts of pure iron by using diamond tool with active cutting edge shift

Large-size thin-walled curved surface parts of pure iron are crucial in aerospace, national defense, energy and precision physical experiments. However, the high machining accuracy and surface quality are difficult to achieve due to the serious tool wear and deformation when machining the parts with conventional cutting tools. In this paper, an elliptical vibration cutting (EVC) with active cutting edge shift (ACES) based on a long arbor vibration device is proposed for ultra-precision machining the pure iron parts by using diamond tool. Compared with cutting at a fixed cutting edge, the influence of ACES on the EVC was analyzed. Experiments in EVC of pure iron with ACES were conducted. The evolutions of the surface roughness, surface topography, and chip morphology with tool wear in EVC with ACES are revealed. The reasonable parameters of ultra-precision machining the pure iron parts by EVC with ACES were determined. It shows that the ACES has a slight influence on the machined surface roughness and surface topography. The diamond tool life can be significantly prolonged in EVC of pure iron with ACES than that with a fixed cutting edge, so that high profile accuracy and surface quality could be obtained even at higher nominal cutting speed. A typical thin-walled curved surface pure iron part with diameter ∅240 mm, height 122 mm, and wall thickness 2 mm was fabricated by the presented method, and its profile error and surface roughness achieved PV 2.2 μm and Ra less than 50 nm, respectively.     

PCD刀具车削不同颗粒含量SiCp/Al复合材料试验研究

碳化硅铝基复合材料具有优良的导热性、较高的比强度和比刚度,在航空航天领域具有广泛的应用前景。由于此复合材料中含有增强相,导致材料的切削加工性能变差。通过试验分析了不同颗粒体积分数(纳米级5%、微米级25%)SiCp/Al复合材料和切削参数(切削速度、背吃刀量、进给量)对刀具磨损和工件表面质量的影响,并对刀具磨损机理进行了研究。试验结果表明,车削微米级25%SiCp/Al材料时聚晶金刚石PCD(Polycrystalline Diamond)刀具磨损更严重,且工件表面质量更差。随着进给量和背吃刀量的增大,工件表面粗糙度值增大,刀片前刀面磨损严重;随着切削速度的增大,工件表面粗糙度值减小,刀片前刀面磨损量增大。选取本文切削参数进行SiCp/Al复合材料的切削加工时,发现刀具磨粒磨损、微崩刃是PCD刀具后刀面磨损的主要成因,且刀具前刀面也会产生积屑瘤。研究结果可为SiCp/Al复合材料PCD车削工艺的优化提供理论基础。     

Fretting wear behaviour of machined layer of nickel-based superalloy produced by creep-feed profile grinding

Fretting wear has an adverse impact on the fatigue life of turbine blade roots. The current work is to comparatively investigate the fretting wear behaviour of the nickel-based superalloy surfaces produced by polishing and creep-feed profile grinding, respectively, in terms of surface/subsurface fretting damage, the friction coefficient, wear volume and wear rate. Experimental results show that the granulated tribolayer aggravates the workpiece wear, while the flat compacted tribolayer enhances ...     

Gaussian process regression model incorporated with tool wear mechanism

Cutting tool condition directly affects machining quality and efficiency. In order to avoid severely worn tools used during machining process and fully release the remaining useful life in the meanwhile, a reliable evaluation method of remaining useful life of cutting tools is quite necessary.Due to the variation of cutting conditions, it is a challenge to predict remaining useful life of cutting tools by a unified model. In order to address this issue, this paper proposes a method for predictin...     

透波性Si3N4陶瓷铣削加工表面边缘破损实验研究

针对透波性Si_3N_4陶瓷铣削加工过程中易出现边缘破损现象,通过不同铣削深度实验研究了边缘破损类型、产生位置以及切深对边缘破损影响,并分析了边缘破损产生机理,最后提出了边缘破损控制方法。结果表明:当切深为0.4~0.8 mm时,边缘破损主要集中于出口棱边和入刀侧边;且脆性域加工过程中随着切深的增加,边缘破损程度呈现增大趋势;降低切深至≤0.3 mm且采用跟随周边走刀方式,并保证入刀处刀尖线速度方向与进给方向夹角不小于90°,可以有效控制边缘破损。研究为提高透波性Si_3N_4陶瓷铣削加工表面质量提供了技术支撑。     

基于域对抗门控网络的变工况刀具磨损精确预测方法

刀具磨损的精确预测对保证零件加工质量、提高生产效率和降低制造成本具有重要作用。在实际加工过程中,切削参数、刀具几何参数、刀具材料等工况复杂多变,工况信息和刀具磨损量对监测信号的耦合作用为刀具磨损的精确预测带来了很大挑战。针对以上问题,提出了一种基于域对抗门控网络（DAGNN）的变工况刀具磨损精确预测方法。引入工况分类网络并利用无磨损量标签样本,通过域对抗和门控过滤机制自适应地从不同工况的原始监测信号中提取表征刀具磨损且对工况变化不敏感的关键信号特征。对信号特征提取网络和刀具磨损预测网络进行迭代优化,从而实现变工况刀具磨损的精确预测。实验结果表明：相比已有的方法,本文方法能够利用少量带磨损量标签的目标工况样本实现刀具材料和刀具直径变化情况下的刀具磨损量精确预测,预测精度大幅提高。     

石英纤维增强聚酰亚胺复合材料超低温铣削实验

石英纤维增强聚酰亚胺复合材料是一种非均匀的各向异性材料,采用传统铣削方法对其进行加工时存在刀具磨损严重、切削力较大、加工效率低等问题。为此本文采用超低温冷却铣削方法对石英纤维增强聚酰亚胺复合材料进行铣削实验,并与传统干铣削方式进行了对比,分析了包括加工表面形貌、粗糙度、切削力和刀具磨损等切削性能。结果表明:两种工况下,表面粗糙度随主轴转速的提高而降低,随切深的增加呈先降低后增大趋势;相对于干铣削,不同切削速度下超低温冷却铣削有效抑制了低速干铣削纤维起毛、高速干铣削黏结剂烧蚀缺陷,表面质量都得到改善,刀具耐用度得到提高。超低温冷却引起的复合材料切削力增大,纤维断屑方式的改变以及切削热的有效降低是提高加工质量的主要原因。     

Hypersonic shock wave and turbulent boundary layer interaction in a sharp cone/flare model

A direct numerical simulation of hypersonic Shock wave and Turbulent Boundary Layer Interaction(STBLI) at Mach 6.0 on a sharp 7° half-angle circular cone/flare configuration at zero angle of attack is performed. The flare angle is 34° and the momentum thickness Reynolds number based on the incoming turbulent boundary layer on the sharp circular cone is Re_θ = 2506. It is found that the mean flow is separated and the separation bubble occurring near the corner exhibits unsteadiness. The Reynolds analogy factor changes dramatically across the interaction, and varies between 1.06 and 1.27 in the downstream region, while the QP85 scaling factor has a nearly constant value of 0.5 across the interaction. The evolution of the reattached boundary layer is characterized in terms of the mean profiles, the Reynolds stress components, the anisotropy tensor and the turbulence kinetic energy. It is argued that the recovery is incomplete and the near-wall asymptotic behavior does not occur for the hypersonic interaction. In addition, mean skin friction decomposition in an axisymmetric turbulent boundary layer is carried out for the first time. Downstream of the interaction, the contributions of transverse curvature and body divergence are negligible, whereas the positive contribution associated with the turbulence kinetic energy production and the negative spatial-growth contribution are dominant. Based on scale decomposition, the positive contribution is further divided into terms with different spanwise length scales. The negative contribution is analyzed by comparing the convective term, the streamwise-heterogeneity term and the pressure gradient term.     

不同刀具车削加工高硅氧玻璃纤维/酚醛树脂切削力研究

为探索高硅氧玻璃纤维/酚醛树脂复合材料的切削加工性能,对该类材料进行大直径薄壁回转类零件的车削加工。采用四种不同刀具进行实验研究,获得了不同切削参数及不同刀具材料对切削力的影响规律。试验结果表明:切削用量三要素中,切削深度对切削力的影响最大,其次是进给量,而切削速度的影响很小。当切削速度为119.32 mm/min、进给量为0.1 mm/r、背吃刀量为0.5 mm时,为最优切削参数。Ti-Al-Si-N纳米涂层硬质合金和超硬材料F2HX无涂层硬质合金刀具适合于低速加工,而PCD刀具则适合于高速加工。     

Tool wear during high speed turning in situ TiCp/TiBw hybrid reinforced Ti-6Al-4V matrix composite

Chipping, adhesive wear, abrasive wear and crater wear are prevalent for both the polycrystalline diamond(PCD) and the carbide tools during high speed turning of TiC_p/TiB_w hybrid reinforced Ti-6Al-4V(TC4) matrix composite(TMCs). The combined effects of abrasive wear and diffusion wear caused the big crater on PCD and carbide tool rake face. Compared to the PCD, bigger size of crater was found on the carbide tool due to much higher cutting temperature and the violent chemical reaction between the Ti element in the workpiece and the WC in the tool.However, the marks of the abrasive wear looked much slighter or even could not be observed on the carbide tool especially when low levels of cutting parameters were used, which attributes to much lower hardness and smaller size of WC combined with more significant chemical degradation of carbide. When cutting TC4 using PCD tool, notch wear was the most significant wear pattern which was not found when cutting the TMCs. However, chipping, adhesive wear and crater wear were much milder when compared to the cutting of titanium matrix composite. Due to the absence of abrasive wear when cutting TC4, the generated titanium carbide on the PCD protected the tool from fast wear, which caused that the tool life for TC4 was 6–10 times longer than that for TMCs.     

TC4的铣削加工中铣削力和刀具磨损研究

通过TC4铣削加工时的铣削力试验,研究了干切削时和有氮气介质铣削时影响铣削力大小的几个因素,为提高金属去除率优化了切削参数。同时通过刀具磨损试验,对上述两种铣削方式,比较了在不同的切削速度下铣削时铣刀后刀面的磨损,证实了以氮气为切削介质能够大大地改善刀具的磨损状况和提高刀具的寿命。     

CFRP铣削有限元模型建立及切削力仿真分析

为探索碳纤维增强树脂基复合材料(CFRP)铣削加工过程中切削力与工艺参数之间的映射关系,建立CFRP铣削加工有限元仿真模型并对切削力进行分析。基于ABAQUS软件通过定义材料属性、材料失效模型、纤维铺层数和纤维方向建立了CFRP铣削加工二维有限元仿真模型,并对该模型进行了实验验证。基于该模型,分析了切削力与纤维方向角、铣削速度、每齿进给量和刀具前角等工艺参数之间的映射关系。仿真结果表明:纤维方向角从0°增大到90°,切削力呈现降低趋势,而纤维方向角从90°增大到180°,切削力呈现增大趋势。随着切削速度和每齿进给量的增大,切削力随之增大,而随着刀具前角增大,切削力随之减小。     

AFM针尖磨损机理研究进展

在分析了原子力显微镜(AFM)探针在测量及加工领域应用过程中,探针磨损对于实验结果的影响的基础上,综述了Si3N4针尖、金刚石针尖和单晶硅针尖的磨损机理。并展望了探针磨损机理的发展趋势。     

Yield anisotropy and tension/compression asymmetry of a Ni3Al based intermetallic alloy

In order to investigate the yielding behavior of the newly developed Ni 3 Al-based intermetallic alloy IC10, yield stresses have been measured in tension and compression with different orientations. The specimens were cut from a sheet with different angles inclined from the solidification direction. The inclined angles were taken to be 0 , 22.5 , 45 , 67.5 and 90 . All experiments were conducted at room temperature except for orientation 0 , whose deformation temperatures ranged from 298 to 1273 K. Experimental results show that the yield strength of alloy IC10 has the anomalous behavior which has been observed for other Ll 2 -long-range ordered intermetallic alloys, but it is less pronounced. The abnormalities show the following characteristics: (i) the yield strength increases as the temperature is raised below the peak temperature, (ii) yield strength anisotropy, (iii) tension/compression asymmetry. Compared to Ni 3 Al single crystals, the polycrystalline exhibits some different yielding behaviors which may be due to the high volume fraction of c phase.