定向凝固钴基高温合金DZ40M的热处理研究

研究了热处理对新研制的定向凝固钴基高温合金DZ40M组织和性能的影响。结果表明 :12 80℃ / 4h固溶处理可完全溶解DZ40M合金中初生碳化物M7C3 和MC ,合金成为单相固溶体。95 0℃和 10 5 0℃时效处理可使DZ40M合金发生硬化 ,以 95 0℃时效硬化效果更为明显 ,相应的峰时效制度为 95 0℃ / 12h和 10 5 0℃ / 2 4h。时效处理引起M2 3 C6沉淀析出。 95 0℃ / 12h时效显著提高DZ40M合金室温强度和高温持久寿命 ,同时也减少了合金塑性 ,但合金仍保持一定的塑性。 10 5 0℃ / 2 4h虽然能增加室温拉伸性能 ,但削弱了高温持久性能     

微量Er,Y对Al-Zn-Mg-Cu-Zr合金均匀化的影响

采用光学显微镜(OM)、差热分析(DTA)、扫描电镜(SEM)、透射电镜(TEM)和X射线衍射(XRD)等分析技术研究了在Al-Zn-Mg-Cu-Zr合金中添加微量稀土元素Er和Y对其均匀化行为的影响。研究结果表明:在Al-Zn-Mg-Cu-Zr合金中复合添加微量Er,Y(质量分数0.4%)使合金的共晶化合物溶解温度升高,其均匀化温度相应提高。合金经二级均匀化处理后仍残留较多的S(Al2CuMg)相和Al8Cu4Er相,其中S(Al2CuMg)相能在三级均匀化条件下得到有效消除,但Al8Cu4Er相很难消除。经465℃/24h+475℃/4h+485℃/4h三级均匀化处理后,合金中残留的共晶化合物数量已经很少,基体上分布有大量、均匀、细小的第二相质点,对抑制合金再结晶,提高合金性能十分有利。     

一种新型Al—Zn—Mg-Cu系铝合金的均匀化工艺研究

采用拉伸性能测试、硬度测试、DSC分析、光学显微镜观察、扫描电镜观察(SEM)和透射电镜观察(TEM)等分析方法,研究了单、双级均匀化工艺对一种新型Al-Zn-Mg-Cu合金组织性能的影响及合金的过烧温度.结果表明,采用常规半连续铸造方法生产的该合金铸坯的过烧温度在480℃左右.随均匀化温度的升高,铸造组织中的非平衡共晶相逐渐溶入基体,均匀化温度达到450℃以上时,枝晶组织基本消失,基体固溶度随均匀化温度的升高而增大.在400℃左右对铸锭进行预处理,可促进第二相Al3Zr均匀弥散析出,抑制随后热加工过程中的再结晶,从而细化晶粒,并改善合金工艺塑性.确定该新型Al-Zn-Mg-Cu合金的均匀化工艺为400～420℃/12h+470℃/36h.     

均匀化处理对7A55铝合金组织与性能的影响

研究了单级均匀化和双级均匀化工艺对铸态7A55铝合金组织和性能的影响规律.结果表明,经450℃单级均匀化处理后,合金中的残留共晶仍然较多,保温60h时合金中残留共晶比例由铸态合金的15.2%减少至7.2%,合金硬度由72HRB降低至60HRB,伸长率则由2.1%增大至11.2%;经450℃/60h+470℃双级均匀化处...     

一级时效对DD3单晶高温合金蠕变性能的作用

根据DD3合金的热分析和相分析结果,设计了以增大.γ'平均尺寸、改善γ'尺寸分布和提高析出相含量为目的的时效和固溶处理制度,进行了提高DD3单晶高温合金蠕变性能的热处理工艺研究.结果表明,增加一级高温时效处理可使γ'相尺寸明显增大;高温时效温度高于1080℃时,γ'相过分长大;1060℃/4h时效处理后,γ'相组织最优;配合在1265℃/4h的固溶处理,γ'相含量得到提高的同时,合金蠕变、拉伸性能优异.组织与性能研究证明,加入一级高温时效处理的新工艺可使DD3合金组织得到明显优化,760～1038℃范围内的蠕变性能获得显著提高.根据该结果,新的热处理工艺确定为:1265℃/4h,AC+1060℃/4h,Ac+870℃/32h.     

Mg—Li合金的均化制度研究

对Mg-Li合金的均匀化工艺及制度进行了研究。实验表明，铸锭包覆铝箔的方法可以使均化过程顺利进行；确定了Mg-Li二元合金的均化制度为300℃×24h，添加合金元素的Mg-7Li-14Zn三元以上的合金均化制度确定为300℃×36h。     

分级时效工艺对1420A1－ Li合金组织与性能的影响

研究了分级时效工艺对1420Al-Li合金组织与性能的影响，试验结果表明经70℃/12h+120℃/4～10h工艺分级时效处理可使1420Al-Li合金的综合力学性能得到显著的提高；分级时效工艺使1420Al-Li合金析出的δ′相粒子分布均匀、尺寸细小。     

固溶温度对C300钨极氩弧焊焊缝成分均匀化的影响

采用光学显微镜、扫描电镜和能谱分析对马氏体时效钢(C300级)钨极氩弧焊焊缝中偏析的合金元素在不同温度固溶时均匀化情况进行了初步的计算和分析。研究认为C300钨极氩弧焊焊缝中主要偏析合金元素是Ni,Mo,Ti;焊缝经1200℃/1h AC处理可以获得成分均匀的马氏体;成分均匀的焊缝进行480℃/4h AC时效处理将不再产生逆转变奥氏体。     

ZK60镁合金均匀化过程中的组织演变

采用光学显微镜、扫描电镜、能谱分析和X射线衍射研究了ZK60镁合金铸态的显微组织以及均匀化过程中的组织演变与成分分布.结果表明:ZK60铸态合金中枝晶偏析严重,在晶界和枝晶边界处存在大量的非平衡共晶相,其主要成分为α-Mg和Mg,Zn,;经过均匀化处理后,合金中的非平衡相随温度的升高和时间的延长逐渐溶解,但温度高于420℃后发生过烧,最佳均匀化处理制度为400℃/12h,该制度与均匀化动力学方程所得结果基本一致.     

热等静压温度对K447A高温合金显微组织及性能的影响

研究了热等静压温度对K447A合金显微组织及性能的影响。测试了合金的持久性能和室温拉伸性能。利用金相显微镜(OM)和扫描电镜(SUM)观察了合金显微组织。结果表明,1185～1210℃/180MPa/4h(+1185℃/2h,AC+1100℃/4h,AC+870℃/20h,AC)下,随热等静压温度的提高,合金中显微疏松逐步闭合,碳化物逐步细化和球化;γ-γ’共晶相尺寸和数量逐步减小,共晶特征趋于不明显;晶界呈不连续颗粒状;存在大、小两种尺寸的γ’相。经1185～1210℃HIP处理的合金980℃/200MPa持久性能大幅提高;经1195℃HIP的合金760℃/724MPa持久性能达到最高。经1210℃HIP处理的合金980℃/200MPa持久性能达到最高。180MPa/4h条件下,K447A合金合适的热等静压温度为1185～1210℃。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.