Spectral Analysis and Subtraction of Noise in Radar Signals

A new method of maximum entropy spectral estimation called the revised maximum entropy method (MEM) is formulated and is applied to the spectral analysis of the echo signals from atmospheric turbulence observed by an incoherent scatter radar. The revised MEM is shown free from many demerits of the other methods for spectral analysis. Further it makes it possible to subtract the white noise usually contained in the data during the processing. Some examples of spectral estimation are shown for the actual radar signals and the simulated data. Another application of the revised MEM is the subtraction of the clutter component which is difficult to do by linear filtering. The method is successfully applied to several data abounding with the clutter to obtain the spectra of the echo signals with less clutter distortion.     

Biparametric CFAR procedures for lognormal clutter

The authors consider procedures for constant false alarm rate in lognormal clutter, accounting for variations of both the scale and a shape parameter of the clutter. Adaptivity to both parameters is obtained through biparametric estimation based on a sliding window surrounding the radar cell under test. Some procedures exploiting best linear unbiased estimation (BLUE) are presented and compared to a previous procedure called Log-t, which uses maximum likelihood estimation (MLE). The comparison is carried on for both a homogeneous clutter environment and for instances of inhomogeneous environment (clutter edges and spurious targets). In the latter instances, some advantages of BLUE procedures which stem from the opportunity of censoring are highlighted     

Rotating Blades Radio Interference in a Helicopter-Borne CW Doppler Radar

Radio interference generated in a helicopter-borne continuous wave (CW) Doppler radar system due to the rotating blades is analyzed. This problem has been previously treated for the case of pulse Doppler radar systems with very narrow (near zero) beamwidth. In this case the strong interference component returning directly from the blades (with no ground reflection) need not be considered as it reaches the receiver when it is still blinded. In the case of a CW Doppler radar, however, this interference component must be included. Numerical calculations show that the total blade interference power level, dominated by the direct component, is higher than that of the direct ground clutter in the radar clutter region. It decreases approximately as (f - fo)-4 in the radar clear region. It stays, however, well above the thermal noise level which might cause false alarm and degrade the radar performance.     

非正侧视阵列机载雷达多空间角补偿算法

 非正侧阵列机载雷达的杂波分布随距离变化而变化,各距离单元的杂波分布不再满足独立同分布条件,造成统计型空时自适应处理(STAP)处理器性能下降。本文提出了一种多空间角补偿(MSAC)的非正侧视机载雷达杂波抑制方法,该方法先通过角度-多普勒补偿(ADC)预处理以消除在谱中心处的杂波非均匀,然后采用MSAC法在多个多普勒方向使参考单元和待检测单元的杂波谱保持一致,从而进一步消除在其余方位的杂波非均匀。仿真结果表明了该方法的性能明显优于ADC法,且运算量增加不多。     

New clutter suppression approach for multifunction radar-radarresource management for the clutter suppression

The use of constant-false-alarm-rate (CFAR) techniques to keep false alarm rates at a suitable low level is reviewed. Radar resource management for clutter suppression, a novel approach for multifunction phased-array radar that can more effectively suppress clutter, is proposed. The results of a simulation study, which indicate the maximum permissible P_fa and the improvement of detection performance, demonstrate the effectiveness of resource management, especially when an all-neighbor filter is used     

Space-time adaptive radar performance in heterogeneous clutter

Traditional analysis of space-time adaptive radar generally assumes the ideal condition of statistically independent and identically distributed (IID) secondary data. To the contrary, measured data suggests realistic clutter environments appear heterogeneous and so the secondary data is no longer IID. Heterogeneity leads to mismatch between actual and estimated covariance matrices, thereby magnifying the loss between the adaptive implementation and optimum condition. Concerns regarding the impact of clutter heterogeneity on space-time adaptive processing (STAP) warrant further study. To this end, we propose space-time models of amplitude and spectral clutter heterogeneity, with operational airborne radar in mind, and then characterize expected STAP performance loss under such heterogeneous scenarios. Simulation results reveal loss in signal-to-interference plus noise ratio (SINR) ranging between a few tenths of a decibel to greater than 16 dB for specific cases     

机载MIMO雷达空时自适应杂波对消器

针对机载多输入多输出(MIMO)雷达杂波分布呈现空时耦合特性,提出一种空时自适应杂波对消器.利用机载MIMO雷达的脉冲回波数据,构造杂波对消器的系数矩阵.通过空时自适应杂波对消器的预处理,可以有效地抑制杂波,并通过与常规空时处理算法的级联,最终可以有效提高动目标的检测性能.实现了由传统地基雷达杂波对消器向机载运动平台的推广.仿真结果表明,这种自适应杂波对消器不仅适用于正侧视雷达,对于非正侧视雷达也同样适用.     

Airborne/spacebased radar STAP using a structured covariance matrix

It is shown that partial information about the airborne/spacebased (A/S) clutter covariance matrix (CCM) can be used effectively to significantly enhance the convergence performance of a block-processed space/time adaptive processor (STAP) in a clutter and jamming environment. The partial knowledge of the CCM is based upon the simplified general clutter model (GCM) which has been developed by the airborne radar community. A priori knowledge of parameters which should be readily measurable (but not necessarily accurate) by the radar platform associated with this model is assumed. The GCM generates an assumed CCM. The assumed CCM along with exact knowledge of the thermal noise covariance matrix is used to form a maximum likelihood estimate (MLE) of the unknown interference covariance matrix which is used by the STAP. The new algorithm that employs the a priori clutter and thermal noise covariance information is evaluated using two clutter models: 1) a mismatched GCM, and 2) the high-fidelity Research Laboratory STAP clutter model. For both clutter models, the new algorithm performed significantly better (i.e., converged faster) than the sample matrix inversion (SMI) and fast maximum likelihood (FML) STAP algorithms, the latter of which uses only information about the thermal noise covariance matrix.     

Analog clutter cancellation algorithms for dynamic range reduction

A technique that effectively reduces the dynamic range of the input signal in a radar receiver prior to digitization is presented. The dynamic range reduction is accomplished through a process that predicts the next radar return signal from the previous return signals, generates a replica waveform, and subtracts this replica waveform from the radar return signal prior to digitization. This process allows the radar return signal to be digitized without distortion by an analog-to-digital converter (ADC) having a limited dynamic range. The full dynamic range of the radar return signal is then restored by adding the replica waveform to the ADC output. Test and evaluation results using both synthetic and recorded radar data demonstrate in excess of a 30-dB reduction in the dynamic range of the signal at the ADC input when strong clutter is present     

Low-altitude target detection by coastline operated marine radar

Relevant to a Richian family of fluctuating targets with a composite background of sea-plus-land clutter, the performance prediction of a radar operating in near-coastal regions is elucidated by assuming noncoherent integration of the pulses. Considering the dominance of land clutter, a modified K-distributed statistic is indicated for the overall clutter envelope; and the corresponding probability of false alarm and probability of detection are deduced for fixed threshold detection (s) based on N pulses integrated in the presence of the sea-plus-land clutter and the noise. Even when the target offers a dominant scattered echo, the worst situations of the land clutter affecting the detection performance are indicated     

Analysis of CFAR performance in Weibull clutter

Recent interest has focused on order statistic-based (OS-based) algorithms for calculating radar detection thresholds. Previous analyses of these algorithms are extended, to determine closed-form approximations for the signal-to-clutter ratio required to achieve a particular probability of detection in clutter environments whose amplitude statistics are modeled by the Weibull distribution, and where the clutter dominates receiver noise. Performance is evaluated in both homogeneous and inhomogenous clutter. The analysis shows that the OS-based algorithm is quite robust against both interference and clutter edges. A method is suggested for improving performance at clutter inhomogeneities for short-range targets     

MTI Optimization in a Multiple-Clutter Environment

A means of optimizing a moving target indicator (MTI) filter for rejecting several types of clutter, which are generated by different mechanisms such as by rain or the ground, is formulated. lt is found that the optimal performance of such a filter depends on the spectral density functions, average radar cross sections, and the relative mean Doppler frequencies of each type of clutter. lt is shown that the optimal improvement factor of such a filter is bounded by the weighted average (weighted in accordance with the radar cross sections of the clutter types) of the improvement factor for the individual clutter type. lt is also shown that the improvement factor of such a filter is a function of the relative mean Doppler frequency f0 between the clutter types. As f0 increases, the performance of the MTI system degrades. The worst improvement factor occurs when f0 is equal to half of the radar pulse-repetition frequency (PRF).     

Measurements of L-band inland-water surface-clutter Doppler spectra

Although radar surface-clutter reflectivities from terrain are generally much greater than those from water, strong Bragg resonances at low but non-zero Doppler frequencies in backscatter from small inland bodies of water might potentially cause false alarms for moving target indicator (MTI) or other Doppler signal-processing techniques designed for target detection in ground clutter. To provide data for investigating this concern, measurements of L-band radar backscatter were recorded from the surface of a small inland freshwater reservoir in central Massachusetts. These measurements were of unusually high system stability and spectral purity so as to provide up to 80 dB of available spectral dynamic range. Strong Bragg spikes occurred in the clutter Doppler spectra from the reservoir at low (3 to 4 Hz) but non-zero Doppler frequencies. This strong Bragg resonance was persistent in time and space throughout the measurements. Spectral results are presented for all four combinations of linear polarization. Comparison with tree clutter spectral results indicates that, when an occasional water body comes under surveillance at vertical polarization in otherwise generally forested terrain, water clutter spectral density is expected to exceed surrounding-terrain tree clutter spectral densities in the Bragg-offset Doppler vicinity by large amounts     

基于梳状谱发生器的毫米波相参脉压模拟器

研制了一种基于梳状谱发生器的全相参脉冲压缩毫米波雷达目标射频回波模拟器。通过与被测雷达共用基准频率参考信号,结合梳状谱发生器及DDS,保证了输出信号和雷达发射信号的相参性和快速频率跳变,实现较好的相位噪声性能和杂散抑制。该系统输出为Ka波段,带宽2GHz,步进100kHz,相位噪声小于一80dBc@1kHz,跳频时间小于2μs。     

Adaptive Radar Detection in Doubly Nonstationary Autoregressive Doppler Spread Clutter

The problem of adaptive radar detection in clutter which is nonstationary both in slow and fast time is addressed. Nonstationarity within a coherent processing interval (CPI) often precludes target detection because of the masking induced by Doppler spreading of the clutter. Across range bins (i.e., fast time), nonstationarity severely limits the amount of training data available to estimate the noise covariance matrix required for adaptive detection. Such difficult clutter conditions are not uncommon in complex multipath propagation conditions where path lengths can change abruptly in dynamic scenarios. To mitigate nonstationary Doppler spread clutter, an approximation to the generalized likelihood ratio test (GLRT) detector is presented wherein the CPI from the hypothesized target range is used for both clutter estimation and target detection. To overcome the lack of training data, a modified time-varying autoregressive (TVAR) model is assumed for the clutter return. In particular, maximum likelihood (ML) estimates of the TVAR parameters, computed from a single snapshot of data, are used in a GLRT for detecting stationary targets in possibly abruptly nonstationary clutter. The GLRT is compared with three alternative methods including a conceptually simpler ad hoc approach based on extrapolation of quasi-stationary data segments. Detection performance is assessed using simulated targets in both synthetically-generated and real radar clutter. Results suggest the proposed GLRT with TVAR clutter modeling can provide between 5–8 dB improvement in signal-to-clutter plus noise ratio (SCNR) when compared with the conventional methods.     

The Effect of Spectral Shape on Clutter Standard Deviation

Many radar systems now employ wideband waveforms and noncoherent averaging techniques to reduce the scintillation of the backscatter from ground clutter. The purpose of this paper is to quantify the effects of the wideband spectral shape on the clutter standard deviation after noncoherent averaging of the received signal. Relationships are developed which quantify the clutter standard deviation for any spectral shape and any ratio of transmitted band-width to processed bandwidth.     

Statistical analysis of real clutter at different range resolutions

A statistical analysis is presented of real radar clutter data collected using the McMaster I FIX radar in 1998 and stored in the Grimsby database. We first show the deviations of the amplitude statistics from the Rayleigh model and the suitability of the K- and Weibull-distribution for the first-order amplitude statistical characterization. Thus we focus on the I and Q components of the available data and study their statistical compatibility with the compound Gaussian model. Towards this goal it has been necessary devising appropriate testing procedures; in particular, with reference to the higher order statistics agreement, we have designed a validation procedure involving the clutter representation into generalized spherical coordinates. Remarkably the results have confirmed the suitability of the spherically invariant random processes (SIRPs) for the correct modeling of the radar clutter. Finally we have performed a spectral analysis highlighting the close matching between the estimated clutter spectral density and the exponential model.     

Radar Partial Coherence Theory: An Introduction

The nature of physical phenomena is such that scattering from portions of an object, a number of objects, or clutter, is not completely unrelated; the underlying environment causes some degree of order in the phenomenon. Radar partial coherence theory describes a structure for the general target, or clutter, and its relationship to radar cross section, waveform coding, and the radar output signal. The clutter ambiguity function is introduced for extended bodies and embraces the (Woodward) ambiguity function for a point target. Due to nonlinear effects caused by partial coherence within the general target, radar signals and targets are formulated in terms of mutual coherence functions. The basic quantities describing the radar output are 1) the radar mutual coherence function (formulated in terms of the radar waveform) and 2) the target mutual coherence function which depends upon target properties, physical environment, and viewing aspect. Random noise (independent point scatterers) and partially coherent portions of reflecting bodies are made accountable in the theory. Partial coherence effects are treated as patches of reflected energy: self-coherent energy patches plus mutually coherent energy among the patches.     

Comparison between monostatic and bistatic antenna configurationsfor STAP

The unique characteristics of bistatic radar operation on the performance of airborne/spaceborne moving target indicator (MTI) radars that use space-time adaptive processing (STAP) are discussed. It has been shown that monostatic STAP radar has the following properties. 1) For a horizontal flight path and a planar Earth the curves of constant clutter Doppler (isodops) are hyperbolas. 2) For a sidelooking antenna geometry the clutter Doppler is range independent. 3) Clutter trajectories in the cosφ-F plane (F=normalized Doppler) are in general ellipses (or straight lines for a sidelooking array). We demonstrate that these well-known properties are distorted by the displacement between transmitter and receiver in a bistatic configuration. It is shown that even for the sidelooking array geometry the clutter Doppler is range-dependent which requires adaptation of the STAP processor for each individual range gate. Conclusions for the design of STAP processors are drawn     

Near-Field Analysis of Helicopter Rotating Blades Modulation Interference

A near-field analysis is carried out to obtain the level of modulation interference due to rotating blades in a helicopter-borne pulse Doppler radar system. The interference power spectra are calculated for different values of antenna depression angle and helicopter (radar) speed at a constant helicopter altitude of 300 m. Numerical results for the case of 1 kW radiated power show that blade interference level is about 5 to 8 dBW/Hz less than that of the direct ground clutter in the clutter region. It extends, however, into the clutter-free region which may cause false alarms and degradation of the radar performance.