共查询到20条相似文献,搜索用时 125 毫秒
1.
微小流量离心压缩机叶轮流场性能模拟计算 总被引:2,自引:0,他引:2
设计了一种空气工质低压比的微小流量、高转速离心压缩机三元叶轮,并对其流场特性进行数值模拟.研究表明:该类叶轮出口与进口区域面积比小于1;采用高转速可以改善该类叶轮的效率;叶轮的最佳叶片数较源于大流量低转速离心压缩机理论的叶片数经验公式计算值要小;叶轮出口角一般在60°以上;叶尖顶部间隙增大时,叶轮总压比及效率显著下降.研究方法和结果为飞机高性能空气循环制冷系统和蒸汽压缩制冷系统中微小流量高转速离心压缩机的工程化设计提供了有益的参考. 相似文献
2.
3.
4.
5.
对于不同的简单式空调制冷系统,内阻高低对系统特性的影响并不一致。经过建模初步分析,给出不同的简单式空调系统在流阻匹配上的倾向性选择。 相似文献
6.
7.
8.
发展了可工程应用的紧凑式换热器传热模型,从三个层次对换热器进行讨论。针对空气循环制冷系统中的换热器,分析了二轮低压除水和二轮高压除水空气循环制冷系统中换热器的传热特性,计算结果与试验数据符合良好。该方法利用较少的实验数据即可得到全高度特性,不仅满足工程计算的要求,而且为评估换热器性能提供了理论依据。 相似文献
9.
本文以两级对置式离心压气机为对象,采用数值模拟方法研究了湿压缩对压气机特性和内部流场的影响。数值计算借助ANSYS CFX软件,采用欧拉-拉格朗日法耦合计算连续流场和离散粒子项,基于k-ε湍流模型、变比热拟合公式计算焓熵值,利用安托万方程求解饱和蒸汽压力并加入液滴破碎CAB模型和撞壁模型。在压气机进口采用干空气和不同喷水量与粒径组合共计7个工况条件下,对比分析了压气机总体性能变化、部件性能变化及水滴的运动轨迹。结果表明,湿压缩使得整机压比和效率均有所提高,但效果越好裕度越小。低压级内湿压缩效果明显,水滴蒸发使得出口温度降低;高压级湿压缩降温增益不明显,但受上一级冷却效果影响,压比和温比都增加。水滴在叶轮中主要积聚在叶片压力面根部。扩压器和回流器中产生了较大的尾迹损失,扩压器前缘受水滴破碎和掺混作用,产生较大熵增。 相似文献
10.
11.
12.
蒸发制冷技术在直升机上的应用 总被引:4,自引:0,他引:4
本文简要介绍了典型的蒸发制冷循环系统工作原理及国外的技术现状,对国外现役直升机采用的蒸发循环制冷系统与空气循环制冷系统进行性能对比,并对蒸发制冷循环系统在直升机上的应用前景进行初步的讨论。 相似文献
13.
对民用飞机座舱制冷系统性能计算方法进行了阐述,并对座舱制冷系统性能计算方法进行了对比分析。 相似文献
14.
《中国航空学报》2020,33(7):1877-1888
The air-cycle refrigeration system is widely used in commercial and military aircraft, and its efficiency greatly affects aircraft performance. Nowadays, this system requires a more efficient design and optimization method. In this paper, a short-cut optimization method with high efficiency and effectiveness is introduced for both conventional and electric air-cycle refrigeration systems. Based on the system characteristics, a four-layer parameter matching algorithm is designed which avoids computational difficulty caused by simultaneous equations. Fuel penalty is chosen as the objective function of optimization; design variables are reduced based on sensitivity analysis to improve optimization efficiency. The results show that the 3-variable optimization of the conventional air-cycle refrigeration system can obtain almost the same results as the traditional 6-variable optimization in that these two optimizations can both significantly reduce the fuel penalty. However, the computer running time of the 3-variable optimization is much shorter than that of the 6-variable optimization. The optimal fuel penalty of the electric air-cycle refrigeration system is lower than that of the conventional one. This study can provide reference for optimizing the air-cycle refrigeration system of aircraft. 相似文献
15.
蒸汽腔平板微热管仿真及传热性能测试 总被引:1,自引:0,他引:1
平板微热管是一种新型的气液两相流传热器件,在空间有限的紧凑器件热控系统中应用更有优势,但是目前性能仍有很大提升空间。首先分析了具有蒸汽腔的平板微热管的工质输运特性,设计并制作了体积为45mm×16mm×1.75mm的蒸汽腔微热管,其中蒸汽腔的深度为200μm。制作了同样尺寸的无蒸汽腔微热管进行传热性能对比。试验结果表明,仿真分析与试验的温度差异在10%左右,高速图像采集系统采集图像与仿真图像可以较好地吻合。当输入功率为6W时,蒸汽腔热管的平衡温度为70.4℃,而相同功率下没有蒸汽腔热管的平衡温度为118℃。在1~6W输入功率下,蒸汽腔热管的平衡温度要明显低于没有蒸汽腔热管的平衡温度,因此蒸汽腔对于减小气态工质循环阻力,提高微热管传热能力有较大影响。本研究可为平板微热管的优化设计提供借鉴。 相似文献
16.
制冷系统性能与制冷工质充注量的多少密切相关,随时间的推移,制冷剂多少总会泄漏,系统制冷剂总量会减少,性能会降低。制冷剂的减少会导致压缩机转速加快,制冷剂冷凝压力降低、蒸发温度升高、过热量加大。 相似文献
17.
《中国航空学报》2023,36(5):202-211
Modeling of a centrifugal compressor is of great significance to surge characteristics and fluid dynamics in the Altitude Ground Test Facilities (AGTF). Real-time Modular Dynamic System Greitzer (MDSG) modeling for dynamic response and simulation of the compression system is introduced. The centrifugal compressor, pipeline network, and valve are divided into pressure output type and mass flow output type for module modeling, and the two types of components alternate when the system is established. The pressure loss and thermodynamics of the system are considered. An air supply compression system of AGTF is modeled and simulated by the MDSG model. The simulation results of mass flow, pressure, and temperature are compared with the experimental results, and the error is less than 5%, which demonstrates the reliability, practicability, and universality of the MDSG model. 相似文献
18.
为了能够使仿真技术更好地应用于制冷空调系统的优化设计,以热动力学为基础,研究了摆动活塞式空气压缩机的动态特性,将压缩机进、排气流道作为制冷系统的一个环节,建立数学模型。针对数学模型进行计算方法的探讨,并编制程序,实施动态仿真,得出动态过程表示在p-V图上,其研究思路为改进压缩机性能提供良好的参考依据。 相似文献
19.
该空气循环制冷设备用于飞机机上环境控制系统不工作状态时,向飞机提供给定温度和湿度的空气,达到降温或除湿的目的。在对该设备工作原理进行深入研究的基础上,针对其热力性能故障,选取了30个监测参数,并采用故障树分析方法,设计了该设备的状态监测与故障诊断系统。这里主要介绍了该系统的状态监测与故障诊断原理、主要功能、及其硬件设计和软件设计。该系统能够快速、准确地确定故障部位,提高维修效率。 相似文献