Zero dynamics-based design of damping networks for switching converters

A new design technique of the input filter damping network for dc-to-dc switching converters of buck type is presented. This technique is derived by means of zero dynamics analysis of the switching converter and yields equivalent results to those obtained using the classical approach based on minimizing the filter output impedance. The new method can be applied in converters of buck type with two inductors, boost with two inductors and dual SEPIC. Simulation and experimental results corresponding to a boost converter with two inductors illustrate the procedure.     

Synthesis and analysis of inductor-isolated switched-mode converter

A procedure is developed for the synthesis and analysis of complete classes of inductor-isolated PWM (pulse width-modulated) converters. The procedure is useful in the identification of converters in which the isolation inductors can be integrated with the rest of the inductors on the same magnetic structures. The information obtained from the procedure is useful in the selection of the converter most suitable for a given application and in the design of this converter with minimum component stresses, high power density, and low cost     

A Pulsewidth-Modulated Dc-to-Dc Converter That Utilizes a Small Number of Components

In general, circuit reliability can be enhanced by either incorporating redundancy or by minimizing a circuits component count. Conventional nonregulating converters generally require two active devices, whereas in regulating converters or switching regulators as many as 10 transistors, either integrated or discrete, is not uncommon. A regulating dc-to-dc converter which provides useful regulation and which can be constructed with either two or three transistors is described.     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

Effect of FET output capacitance on ZVS of resonant converters

The analysis of resonant converters including the capacitance of the switches is presented. New dc characteristics are obtained for the series, parallel, and series-parallel resonant converters (SPRC). The operating regions where the converters operate with zero-voltage switching (ZVS) are determined as a function of the switch capacitance. The more pronounced effect can be seen in the series resonant converter (SRC), while the parallel resonant converter (PRC) is the most insensitive. The results of the analysis have been verified on an experimental prototype     

General rules for signal flow graph modeling and analysis of dc-dc converters

Signal flow graph (SFG) nonlinear modeling approach is well known for modeling dc-dc converters. However, all possible SFGs of a given dc-dc converter system will not yield the generalized graph. A systematic procedure and guidelines for developing unified flow graph models of the dc-dc boost converters, from which complete behavior can be determined is presented. Usefulness of the proposed method is demonstrated through examples. As an illustration a 2-cell cascade boost and interleaved boost converter systems are taken as examples. Derivation of large, small-signal and steady-state models from generalized flow graph is also demonstrated. Large-signal model is developed and programmed in TUTSIM simulator. Large-signal, responses against supply and load disturbances are obtained. Experimental observations are provided to validate the proposed algorithm.     

高速A/D变换器的电路设计

本文介绍了用常见的中、小规模集成电路设计成高速 A/D 变换器。同时又利用了它的并行传输数字量的速度大大于它本身变换速度的特点,设计了两路在时序上采用相差半个周期来对输入模拟信号交替采样,使 A/D 变换器变换速度达到1MHz 以上。线路实验证明该设计是正确的,实验结果是理想的。并有广泛的使用价值。     

Design and technology of compact high-power converters

New material technologies such as Silicon Carbide (SiC) are promising in the development of compact high-power converters for next-generation power electronics applications. This paper presents an optimized converter design approach that takes into consideration non-linear interactions among various converter components, source and load. It is shown that with the development of high-temperature, high-power SiC power module technology, magnetic components and capacitors become important technology challenges, and cannot be ignored. A 50% improvement in power density is calculated for a 100 V-2 kV, 7 kW SiC DC-DC power converter operating at 150°C compared to a silicon power converter. The SiC power converter can be operated at junction temperatures in excess of 300°C (as compared to 150°C for a silicon power converter) with reasonable efficiency that potentially leads to a significant reduction in thermal management     

Table-Aided Design of the Energy-Storage Reactor in DC-to-DC Converters

A new procedure for the selection of magnetic cores for use in energy-storage dc-to-dc power converters that eliminates the need for an automated computer search algorithm and stored data file is presented. The converter configurations included in the procedure are the three commonly encountered single-winding converters for voltage stepup, for current stepup and voltage stepup/current stepup, and for the two-winding converter for voltage stepup/current stepup. For each converter configuration, three types of controllers are considered: constant-frequency, constant on-time, and constant off-time. Using concepts developed from analyses of these converters by considering the transfer of energy by means of an energystorage inductor or transformer, a special table of parameters calculated from magnetic core data is constructed, which leads to a considerably simplified design procedure.     

A Large-Signal Dynamic Simulation for the Series Resonant Converter

A simple nonlinear discrete-time dynamic model for the series resonant dc-dc converter is derived using approximations appropriate to most power converters. This model is useful for the dynamic simulation of a series resonant converter using only a desktop calculator. The model is compared with a laboratory converter for a large transient event.     

Simplified analysis of PWM converters using model of PWM switch.Continuous conduction mode

A circuit-oriented approach to the analysis of pulsewidth modulation (PWM) converters is presented. This method relies on the identification of a three-terminal nonlinear device, called the PWM switch, which consists of only the active and passive switches in a PWM converter. Once the invariant properties of the PWM switch are determined, its average equivalent circuit model can be derived. This model is versatile enough to easily account for storage-time modulation of bipolar junction transistor(s) (BJTs); the DC- and small-signal characteristics of a large class of PWM converters can then be contained by a simply replacing the PWM switch with its equivalent circuit model. The methodology is very similar to linear amplifier circuit analysis, whereby the transistor is replaced by its equivalent circuit model     

Unified approach to developing single-stage power converters

A unified approach to developing single-stage power converters which can fulfil multiple functions is presented. Four synchronous switches corresponding to the four common node types of two active switches are introduced. The approach is then to replace the active switches in multistage converters (in cascade or cascode connection) with one or several of the synchronous switches and their degenerated versions to form a single-stage converter. Illustrations of using these switches to develop single-stage converters are presented. These are started with the development of the well-known single-stage switch-mode converters (SMCs), buck-boost, Cuk, sepic, and Zeta (also named dual sepic), from the basic converters, buck and boost. Then, synthesis and applications of other single-stage converters are addressed. Due to increased component stresses, the developed single-stage converters are primarily suitable for applications with moderate power levels     

Current distribution control for parallel connected converters. I

For pt.II, see ibid., vol.28, no.3, p.841-851 (1992). A master-slave control scheme for a uniform current distribution among converter modules in a parallel connected system is presented. In this technique, inner current loops are introduced to the system to achieve output current equalization. The current distribution error is used as a criterion for judging system performance. Using this control scheme, the current distribution error can be reduced greatly even with nonidentical converters in the system. To optimize system efficiency and facilitate the fault-tolerant algorithm realization, this technique is refined so that only the necessary number of converters are activated for different load conditions     

单端正激ZVT功率变换器实现

介绍一种单端正激工作方式的零电压过渡（ＺＶＴ）软开关ＤＣ－ＤＣ变换器;描述该变换器的原理和特征;给出了应用ＺＶＴ软开关技术和集成控制块ＳＧ３５２５Ａ的２４Ｖ／９ＡＤＣ－ＤＣ变换器电路和实验结果。     

Alternate forms of the PWM switch models

Vorperian's pulsewidth modulation (PWM) switch model consists of a PWM transformer and a nonlinear resistor. The recognition that any of the three transformer terminals can serve as the common terminal leads to two alternate PWM transformer models and the corresponding two alternate PWM switch models. For a given PWM dc-dc converter, one of the three PWM switch models is more “natural” for graphic-oriented analysis/design, e.g., it allows the idealized converter to be analyzed by inspection. Furthermore, all three PWM transformers may be used to graphically manipulate the converter circuit to a form that can be analyzed by inspection. The alternate forms of the PWM transformers and the PWM switch models are effective as graphic-oriented teaching and learning tools for PWM converters. This is demonstrated using examples based on the boost converter and the Cuk converter     

Series of radiation-hardened, high efficiency converters for high voltage bus

A review of common switching techniques for dc/dc power conversion is presented. The evolution of the forward converter is discussed, leading naturally to the introduction of the double forward converter. Technical details for a series of radiation-hardened converters are then provided. This series was designed for space power management and distribution (PMAD) applications. The successful development of the PMAD converter demonstrated the viability of high voltage bus.     

Small signal analysis of the LCC-type parallel resonant converter

In this paper, the small signal analysis of the LCC-type parallel resonant converter (LCC-PRC) operating in the continuous conduction mode is given. This analysis is based on both the state-plane diagram, which has been successfully used to obtain the steady state response for resonant converters, and the Taylor series expansion. Applying perturbation directly to the steady state trajectory, a discrete small signal model for the converter can be derived in terns of the input voltage, switching frequency, and the converter state variables. Based on this analysis, closed-loop form solutions for the input-to-output and control-to-output transfer functions are derived. It is shown that the theoretical and computer simulation results are in full agreement     

Steady-state analysis of the constant-frequency clamped seriesresonant converter

A constant-frequency diode-clamped series resonant converter (CFCSRC) is proposed as a solution to problems associated with frequency-controlled resonant converters. This converter has two resonant frequencies, and control is achieved by varying the relative time spent at each switching frequency. Two zero-current-switching (ZCS) modes are examined and plotted in the output plane. An equation is given for the boundary between the two ZCS modes, as well as an expression for the boundary between ZCS and non-ZCS operation; both are plotted in the output plane. The output equation for the main mode is shown to be hyperbolic. Converter peak voltages limited to the input voltages, and peak currents are less than those of the frequency-controlled clamped series resonant converter over a large operating range. Data from a prototype converter are compared with theoretical data and are shown to be in good agreement with the theoretical model     

A study of volume versus frequency for soft switching IGBTconverters

Earlier references have described a new soft switched ZVS/ZCS (zero voltage switching, zero current switching) converter for IGBTs that allows operation above 20 kHz. Although frequencies above 20 kHz are now possible for IGBT converters, the optimum frequency for minimum volume may be below 20 kHz because of heat sink requirements. A comparative study considers the reactive component versus heat sink volume tradeoff for two 6 kW converters, one using ZVS/ZCS and the other using a more conventional circuit with hard switching     

飞机二次电源控制器监测电路的分析与计算

对于某些飞机二次电源供电的机载设备,采用两台变流机作为电源,并配备一台控制器。当主变流机发生故障,控制器能使主弯流机停止工作并起动备用变流机向设备供电。文章应用对称分量法分析计算了主变流机在上述两种状态下,监测电路能输出差别甚大的电压信号,从而如实反映主变流机正常工作和故障两种状态。