A Raw Signal Simulator for Bistatic SAR

This article proposes a new efficient raw signal simulator for the bistatic synthetic aperture radar (SAR) based on 2D fast Fourier transform (FFT) to deal with cases of both ideal trajectory and trajectory deviation. It begins with analyzing the geometric configuration and the range history of the bistatic SAR in side-looking and squint modes of ideal trajectory as well as trajectory deviation. Then a detailed and mathematical study is conducted on the equivalence relation of bistatic-to-monostatic applications (BTMA) in the case of ideal trajectory and trajectory deviation. Also a set of formulas are derived for the equivalence relation between bistatic SAR and monostatic SAR on some reasonable assumptions. Therefore, the application of the simulation method based on the 2D FFT for the monostatic SAR can be extended to the case of bistatic SAR. Finally, the simulation results prove the validity of this method. By comparing the efficiency of the proposed method with that of the time domain method, it is shown that the former is a few orders of magnitude higher.     

Performance of spaceborne bistatic synthetic aperture radar

This paper reports on a model developed for evaluating major system performance of a spaceborne bistatic synthetic aperture radar (SAR) for remote sensing applications. The procedure accounts for formation flying aspects. It is particularly aimed at comparison of monostatic and bistatic cases, and, as a test case, it is applied to study a novel configuration, based on a small satellite equipped with a receiving-only antenna orbiting in tandem with a large, noncooperative transmitting spacecraft, the Italian COSMO-SkyMed mission. Numerical results and plots show the effectiveness of the procedure as a mission design tool and put in evidence key issues and characteristics of the proposed spaceborne bistatic formation.     

双基地聚束SAR运动误差分析

将三维坐标系引入运动误差分析,建立了对任意匀速直线航迹双基地聚束SAR运动误差统一、清晰的分析方法;在此三维坐标系下,推导出各种运动误差引起的相位误差的计算公式。推导基于一般的双基地聚束SAR回波模型,可适用于任意匀速直线航迹的双基地聚束SAR,并且将通常的单基地SAR的运动误差分析作为一种特例也涵盖在内。给出了位置误差、速度误差和加速度误差所造成的相位误差计算公式。从推导结果得出结论:位于不同平台的同一误差,引起的相位误差是不同的;在小场景假设下,双基地聚束SAR的运动误差是空不变的,与目标位置无关。计算机仿真验证了误差分析的正确性。     

一种基于改进WLBF频谱的异构双基地前视SAR成像算法

异构平台组成的双基地前视合成孔径雷达（SAR）配置灵活,可实现多种构型下的前视成像,具有潜在的应用价值。然而特殊的几何构型使得其回波信号具有新的特性,给频谱模型的推导及成像算法的设计带来不便。针对这一问题,提出了一种基于改进WLBF （Weighted Loffeld's Bistatic Formula）频谱的双基地前视SAR成像算法。首先,引入时域去走动和切比雪夫降阶法,减小了传统频谱模型中相位历程的加权分割误差和二阶展开误差,在此基础上推导了回波信号的改进WLBF频谱表达式。然后,使用切比雪夫多项式将改进WLBF频谱展开并设计了双基地前视SAR成像算法。最后,对频谱模型和成像算法进行了仿真分析。结果表明所提改进WLBF频谱模型与传统频谱模型相比具有较高的精确度,设计的成像算法可满足异构双基地大前视系统的成像要求。     

Effects of two-way decorrelation on radar detection inscintillation

A 3 dB gain in average signal-to-noise ratio of a monostatic radar operating in scintillation has recently been established both theoretically and observationally. The statistics of two-way scintillation are derived here for the case where the uplink and downlink both experience Rayleigh fading and where there is arbitrary correlation between the scintillation on the two paths. These statistics are then used to compute radar detection curves. A surprising result is obtained. The probability of detection is only weakly dependent (for P _D in the range 0.1 to 0.9) on the degree of uplink-downlink correlation in the scintillation when the average (nonfading) signal-to-noise ratio is constant and when proper account is taken of the change in mean power between the monostatic and bistatic cases. Much larger differences are seen in the detection curves with scintillation compared with nonfading curves (for P_D equal to 0.7 this scintillation loss is about 7 dB). Thus the difference in detection performance of monostatic and bistatic radars is determined primarily by the difference in the radar cross section (RCS) of the target for the two cases     

ISAR imaging using an emulated multistatic radar system

The use of a monostatic radar configuration limits the ability of an inverse synthetic aperture radar (ISAR) system to image targets in certain geometries. By employing multistatic geometries this limitation may be overcome. This paper discusses the emulation of multistatic geometries, via sea surface multipath reflections, using a monostatic system. This application capitalises on the advantages provided by both monostatic and bistatic systems. The possibility of obtaining ISAR images using these emulated multistatic radar configurations is first theoretically discussed and then verified using experimental results.     

平移不变模式双基地SAR距离聚焦深度分析

根据平移不变模式双基地合成孔径雷达的空间几何关系模型,分析了平移不变模式双基地合成孔径雷达点目标的距离徙动特性,并进一步推导出了平移不变结构双基地合成孔径雷达的距离聚焦深度计算公式。该式表明平移不变结构双基地SAR距离聚焦深度与双基地角、方位分辨力、收发分机波束指向和目标到飞机最近距离之比有关。最后通过仿真,验证了理论分析的正确性。     

一种新的非平行轨迹机载双站斜视SAR成像算法(英文)

本文提出了一种用于非平行轨迹机载双站斜视SAR条带模式成像的新的解析算法。该算法用收、发雷达的多普勒调频率贡献比为加权系数推导了点目标回波的二维频谱。通过解目标位置相对于收、发载机飞行轨迹的耦合,将这个二维频谱中目标的距离参数和方位参数进行了分离。在二维频域内,补偿掉双站扭曲项后利用二维Chirp-Z变换(2D-CZT)校正了距离向和方位向的徙动,获得了精确聚焦的目标图像。雷达回波的二维残余徙动用沿距离向和方位向的分块来限制,推导了数据分块的条件,由此可以实现宽场景成像。仿真试验验证了这种2D-CZT算法的有效性。     

"狼群"干扰对单、双基地雷达的干扰分析

"狼群"干扰是美国正在研制的一种分布式干扰.文中分析了"狼群"干扰对单、双基地雷达的影响,结果表明,"狼群"干扰对单、双基地雷达构成了严重的威胁.在理论分析计算的基础上,提出了抗"狼群"干扰的可能方法.     

基于先验误差模型的机载高分宽幅DBF-SAR自聚焦算法

高分宽幅（HRWS）数字波束形成（DBF）合成孔径雷达（SAR）利用多通道空间采样代替部分时域采样,可以有效缓解SAR成像时高分辨率与宽测绘带间的矛盾,具有重要的军用和民用价值。现有常规DBF-SAR成像算法都假设雷达传感器相对位置精确已知,实际应用中受传感器位置测量误差影响,由位置不精确导致的相位误差会严重影响DBF-SAR高精度成像能力。在极坐标格式算法（PFA）框架下,推导了DBF-SAR成像处理后,残留相位误差的解析模型,分析了该误差对成像质量的影响。依据推导的先验相位误差解析结构模型,提出了一种基于图像对比度最优化准则的自聚焦算法。新算法通过引入先验相位结构信息,极大降低了待估参数的空间维数,可以同时改善自聚焦算法的参数估计精度和计算效率。数据处理结果验证了理论分析的正确性和所提算法的有效性。     

表面不连续特征双站散射特性的试验研究

 采用一种新颖的不连续特征双站雷达散射截面（RCS）测试方法,通过系列化测试,研究了单直缝隙板、单直台阶板的双站散射特性,提出了不连续特征双站散射具有相似性、对称性和平移性的特点,分析了不同不连续特征具有的异同点。试验结果表明：对不连续特征,不同双站下的RCS散射曲线均具有和对应入射频率下的单站散射曲线分布形式相似的特点,同时不同的不连续特征对幅值的影响不同;如果测试方式和试验件对称,则双站和单站散射曲线均具有关于峰值所在方位角对称的特点,单直缝隙板由于试验件本身的对称性表现为较好的曲线对称性,而单直台阶板则表现为稍弱的对称性;散射曲线随双站角的增大,具有明显的平移特性,平移的幅度为双站角的1/2,平移方向为从发射天线指向接收天线,平移后的曲线峰值处于发射天线和接收天线夹角平分线上。     

GEO星弹双基SAR多普勒分辨率特性分析

通过对地球同步轨道（GEO）卫星运动特点的分析，阐明其对多普勒分辨率的影响。传统的双基合成孔径雷达（SAR）多普勒分辨率表达式由于不考虑雷达平台加速度矢量带来的影响，并不适用于GEO星弹双基SAR系统。根据收发平台的双曲线轨迹对目标的回波多普勒特性影响，首先利用梯度方法推导了GEO星弹双基SAR系统的多普勒分辨率表达式；随后详细地分析了GEO卫星与导弹的空间几何关系及多普勒参数，特别是加速度矢量对多普勒分辨率的影响。仿真结果验证了所推导多普勒分辨率表达式的有效性，其有助于双基SAR理论系统完整性的提高，为后续系统设计及应用实践提供理论支撑。     

Effects of polarization and resolution on SAR ATR

Lincoln Laboratory is investigating the detection and classification of stationary ground targets using high resolution, fully polarimetric, synthetic aperture radar (SAR) imagery. A study is summarized in which data collected by the Lincoln Laboratory 33 GHz SAR were used to perform a comprehensive comparison of automatic target recognition (ATR) performance for several polarization/resolution combinations. The Lincoln Laboratory baseline ATR algorithm suite was used, and was optimized for each polarization/resolution case. Both the HH polarization alone and the optimal combination of HH, HV, and VV were evaluated; the resolutions evaluated were 1 ft/spl times/1 ft and 1 m/spl times/1 m. The data set used for this study contained approximately 74 km/sup 2/ of clutter (56 km/sup 2/ of mixed clutter plus 18 km/sup 2/ of highly cultural clutter) and 136 tactical target images (divided equally between tanks and howitzers).     

Taylor expansion of the differential range for monostatic SAR

The polar format algorithm (PFA) for spotlight synthetic aperture radar (SAR) is based on a linear approximation for the differential range to a scatterer. We derive a second-order Taylor series approximation of the differential range. We provide a simple and concise derivation of both the far-field linear approximation of the differential range, which forms the basis of the PFA, and the corresponding approximation limits based on the second-order terms of the approximation.     

基于塔形形态算法的SAR图像相干斑抑制

提出将塔形形态算法用于抑制SAR图像中相干斑处理，为减少塔形处理中由于下采样造成的信息损失，从并行处理的角度出发，对塔形形态滤波器提出了改进，将下采样中的各子图同时进行形态滤波处理，在上采样中将各子图合并。经分析和处理表明这两种算法用于SAR图像滤波都能有效地去除相干斑噪声。与塔形形态滤波、Lee滤波器算法比较，采用并行算法处理后图像的各项指标有明显的改善。     

基于CZT的机载并行双站斜视SAR成像算法

建立了机载并行双站斜视合成孔径雷达(SAR)的几何模型,给出了雷达回波的数学表达式,推导了它的二维频谱并对其特点做了分析。在二维频域内,先用聚焦函数对观测场景中心的点目标做精确成像,然后用Chirp-Z变换(CZT)校正中心点两侧目标回波的距离徙动,再通过方位向逆傅里叶变换得到了雷达图像。该算法利用了CZT能够处理非线性调频信号的特点,简化了处理过程,提高了计算效率和成像精度。仿真实验验证了这种基于CZT的新算法在处理并行双站斜视SAR数据时的有效性。     

双基地角时变下的ISAR稀疏孔径自聚焦成像

针对双基地角时变下的逆合成孔径雷达（ISAR）成像分辨率低以及稀疏孔径存在相位误差引起图像散焦等问题,提出了一种基于贝叶斯压缩感知（BCS）的双基地ISAR稀疏孔径自聚焦高分辨成像算法。在平动补偿后回波数据的基础上,首先构造补偿相位将由双基地角时变引起的多普勒偏移补偿掉,然后构造随双基地角变化的稀疏基矩阵,建立基于压缩感知的双基地ISAR稀疏孔径观测模型,并将相位误差作为ISAR成像的模型误差,接着假设目标图像各像元服从Laplace先验、噪声统计特性服从Gaussian分布,利用贝叶斯推理进行"分布式"迭代求解,在高分辨成像的同时实现了相位自聚焦,仿真结果验证了算法的有效性和优越性。     

Comparison between monostatic and bistatic antenna configurationsfor STAP

The unique characteristics of bistatic radar operation on the performance of airborne/spaceborne moving target indicator (MTI) radars that use space-time adaptive processing (STAP) are discussed. It has been shown that monostatic STAP radar has the following properties. 1) For a horizontal flight path and a planar Earth the curves of constant clutter Doppler (isodops) are hyperbolas. 2) For a sidelooking antenna geometry the clutter Doppler is range independent. 3) Clutter trajectories in the cosφ-F plane (F=normalized Doppler) are in general ellipses (or straight lines for a sidelooking array). We demonstrate that these well-known properties are distorted by the displacement between transmitter and receiver in a bistatic configuration. It is shown that even for the sidelooking array geometry the clutter Doppler is range-dependent which requires adaptation of the STAP processor for each individual range gate. Conclusions for the design of STAP processors are drawn     

基于稀疏分解的空间目标双基地ISAR自聚焦算法

空间目标双基地逆合成孔径雷达（ISAR）成像中,双基地角时变会造成二维图像的散焦。针对此问题,在三大同步理想可实现的条件下,以平稳空间目标为研究对象,分析了空间目标双基地ISAR成像原理,研究了双基地角时变对二维图像散焦的影响机理,提出了利用稀疏分解实现高精度自聚焦的算法。首先,将半双基地角的余弦进行泰勒展开;其次,结合目标的平动及转动条件,将成像相位项用多项式建模;然后,利用稀疏分解算法估计多项式的二次项系数,据此构建补偿项完成相位补偿。算法利用L-曲线准则选取正则参数,基于目标尺寸的先验信息构建冗余基的高分辨因子,利用推广的正则化欠定系统聚焦求解（FOCUSS）算法实现稀疏表示系数的估计,在恰当选取词典分辨率的条件下,算法可实现二次相位项的精确补偿,仿真实验验证了算法性能优于常用的非参数化自聚焦算法。     

SAR极坐标格式成像算法对运动目标响应特性

运动目标的合成孔径雷达（SAR）成像特征是SAR地面运动目标指示（SAR/GMTI）系统进行运动目标检测、成像和重定位的基础。为此,从信号二维解耦合校正距离徙动角度推导和分析了极坐标格式算法（PFA）对运动目标的响应特性,揭示了极坐标格式转换过程中的距离插值和方位插值对运动目标距离徙动的校正原理。理论分析表明：PFA在完成对静止目标成像的同时,还能够自动校正所有运动目标的线性距离徒动,且校正过程无需目标运动信息,因此对于径向运动目标,在忽略波前弯曲条件下PFA也能够对其进行完全聚焦。最后,通过仿真数据处理对理论分析结果进行了验证,表明PFA作为一种运动目标成像预处理方法具有很大的应用前景。