A comparative study on acoustic damping induced by half-wave, quarter-wave, and Helmholtz resonators

The damping characteristics of three-type resonators, a half-wave, a quarter-wave, and a Helmholtz resonator are studied experimentally by adopting linear acoustic test. A quantitative acoustic property of sound absorption coefficient in a model enclosure with the resonators is measured and thereby, the acoustic-damping capacity of a resonator is characterized. For a comparative study on acoustic damping, the damping capacity of a half-wave resonator is compared with that of the other resonators. A half-wave and a quarter-wave resonators have the same damping mechanism, but a quarter-wave resonator has much larger damping capacity than a half-wave resonator with the same diameter of a single resonator. It is found that shorter length of a resonator has the advantage of longer one with respect to the damping capacity. The damping capacity of a Helmholtz resonator increases with cavity volume and does as the orifice length decreases. A Helmholtz resonator has the highest damping capacity of three-type resonators and a half-wave resonator has the lowest. Besides, a Helmholtz resonator requires the smallest number of resonators for optimal damping. The design criterion of each resonator on the optimal damping is provided by the normalized parameter of open-area ratio and the similarity behavior for the optimal damping is observed for various enclosure diameters.     

止裂孔尺寸对止裂效果影响的研究

当航空器结构在航线使用过程中出现疲劳裂纹损伤时,通常在裂纹尖端打止裂孔进行临时性修理。通过理论分析和计算及试验分析,研究了止裂孔尺寸对止裂效果的影响。结果表明,当航空器结构出现疲劳裂纹损伤时,采用5.57～7.14mm直径的止裂孔进行止裂修理,止裂效果较好;当止裂孔直径为6.35mm时,止裂效果最好。     

液体冲压发动机控制系统半实物仿真

运用小偏离线性化理论和Willoh方法，建立了液体冲压发动机和弹体动态数学模型。动态数学模型在微型计算上一体化运行，形成液体冲压发动机／弹体一体化实时数字仿真器。实时数字仿真器通过输入输出接口与液体冲压发动机的实际控制系统进行联接，组成液体冲压发动机、弹性和发动机控制系统半实物仿真系统。对冲压发动机飞行马赫数和控制 系统供油量的半实物仿真结果表明，系统能满足研制工作的需要。     

大小叶片轴流级反问题设计及数值模拟

 在常规轴流级流线曲率法通流设计和任意中弧线叶型造型方法的基础上,引入了适合于大小叶片的当量扩散因子叶型损失模型,发展了用Miller-Lewis-Hartmann(M-L-H)模型分别计算大叶片和小叶片激波损失的复合激波模型,制定了大小叶片装配方法,建立了大小叶片通流反问题设计系统。用该系统对某级增压比为2.20的单级高负荷后掠风扇进行了后掠和前掠大小叶片改型设计。经计算流体力学(CFD)检验,维持后掠造型的改型,在不提高设计点增压比的条件下,级绝热效率相当,流量和失速裕度都得到了提高;而大小叶片结合前掠的改型,当考虑单排静子的最大载荷将设计级增压比提高至2.31时,级绝热效率略微降低约0.3%,流量略减,失速裕度则显著提高。算例也表明通流反问题设计系统适合于大小叶片轴流级的设计。     

利用二次优化实现柔性冗余度机器人关节力矩最小化研究

对基于振动抑制的柔性冗余度机器人关节力矩的最小化进行了研究。通过分析影响柔性机器人弹性动力响应的因素,得出了在结构参数不变的情况下可以通过适当调整关节运动参数来提高机器人动态性能的结论。在此基础上,通过对柔性冗余度机器人的关节运动进行研究,提出了通过自运动的适当选取从而抑制机器人柔性振动的方法。通过对满足抑振要求的自运动的选取进行分析,指出柔性冗余度机器人在实现振动抑制的基础上还具有二次优化的能力,并且利用这种二次优化的能力得出了基于振动抑制的最小化关节力矩的方法。数值仿真验证了该方法的有效性。     

Simulation on effect of throat contraction ratio and strake stagger angle on flow field and aerodynamic performance of scrampressor

The design methods of typical supersonic aircraft intakes and shock wave compression technology have been applied to ram-rotor, an attractive compression system. A ram-rotor is of a typical structure including the compression ramp, the throat and the subsonic diffuser; a scrampressor is similar to ram-rotor, the only difference is that scrampressor has no subsonic diffuser. The work was the continuation of the preparatory work. In order to further study the effect of throat contraction ratio and strake stagger angle on the flow field and performance of a scrampressor, the flow field of a scrampressor with a three-dimensional flow path was numerically simulated with different throat contraction ratios and strake stagger angles. Simulated results indicated that the optional aerodynamic performance of a scrampressor could be achieved with an adiabatic efficiency of 0.8413 a total pressure recovery coefficient of 0.8446, a total pressure ratio of 7.14 and a static pressure ratio of 5.17 for a throat contraction ratio of 0.6 and a strake stagger angle of 12°. It was therefore concluded that an appropriate decrease in throat contraction ratio and an increase in strake stagger angle could help the comprehensive improvement of a scrampressor in performance.      

受均匀内压作用的偏置孔边径向裂纹的应力强度因子的一种求解方法

本文利用一种新的混合法——光弹性实验与权函数解法相结合求解了孔壁受均匀内压作用偏置圆孔边径向裂纹的应力强度因子,该方法具有简单、经济、精度高等优点,对分析复杂应力场中圆孔边穿透裂纹问题,该方法同样适用,且优点更为突出.     

BLOCK DIAGONAL FORM AND BLOCK DIAGONAL CONTROLLER OF NONLINEAR SYSTEMS

G.Meyeretal[l~3Jdescribedthemotionofahelicopterasablocktrianglesystem(BTS),makingitdifferentfromageneralaffinenonlinearsystem.Uptonow,itistruethatBTScanbeexactlylinearized.Thus,thefirstproblem(whetherlinearizableornot)thatfacestheengineerissolved.Thesecondoneishowtoobtainatransformation.AccordingtothefeatureofBTS,MeyeretalconstructedWT-mappingandsolvedtheproblemeasily.Afterhavingstudiedtheequationsofmotionofamissile,theauthorsdiscoveredthatthemodelcalledblockdiagonalnonlinearsystem(BDN…     

用于雷达波形的无损压缩编码

讨论了用算术编码实现波形数据的无损压缩。对波形数据进行无损压缩时 ,如果把每个可能的样本值看作一个符号 ,符号表会非常庞大 ,导致算法不可行。基于这种原因 ,本文用一个符号表示一定范围内波形数据 ,而不是单个波形数据 ,然后在此基础上设计了一种编码方案。先是无损线性预测 ,去除了波形数据之间的相关性。并假定产生的差值序列具有白功率谱 ,幅度服从高斯分布 ,第二步是算术编码。最后给出了对雷达回波数据进行压缩的实验结果。     

多线程控制技术在面向对象实时仿真中的应用

随着实时仿真复杂性的提高,单个的处理器不足以完成所有的必需仿真计算任务。希望能在不同的处理器上完成实时仿真的不同任务,对称多处理器的机制需要软件支持,以使每个处理器通过共享内存进行信息交换。利用多线程控制技术,可以在非全进程开销或不使用共享内存的条件下,使用多处理器。其理由在于线程本身就蕴涵有共享地址的概念。一个多线程的实时程序,利用其中的主线程控制其它的辅助线程,每个处理器用于完成一个辅助的实时计算线程,主线程负责实时时钟的监控,当时钟到达时,启动相应的辅助线程,辅助线程利用图形用户界面(GUI)来监控仿真的进行。     

Determination of a suitable set of loss models for centrifugal compressor performance prediction

Performance prediction in preliminary design stages of several turbomachinery components is a critical task in order to bring the design processes of these devices to a successful conclusion.In this paper,a review and analysis of the major loss mechanisms and loss models,used to determine the efficiency of a single stage centrifugal compressor,and a subsequent examination to determine an appropriate loss correlation set for estimating the isentropic efficiency in preliminary design stages of centrifugal compressors,were developed.Several semi-empirical correlations,commonly used to predict the efficiency of centrifugal compressors,were implemented in FORTRAN code and then were compared with experimental results in order to establish a loss correlation set to determine,with good approximation,the isentropic efficiency of single stage compressor.The aim of this study is to provide a suitable loss correlation set for determining the isentropic efficiency of a single stage centrifugal compressor,because,with a large amount of loss mechanisms and correlations available in the literature,it is difficult to ascertain how many and which correlations to employ for the correct prediction of the efficiency in the preliminary stage design of a centrifugal compressor.As a result of this study,a set of correlations composed by nine loss mechanisms for single stage centrifugal compressors,conformed by a rotor and a diffuser,are specified.     

带止口法兰连接结构刚度特性对结构振动影响

对带有止口的法兰连接结构刚度特性进行了数值仿真研究。使用有限元软件ANSYS分析了带有止口的法兰连接结构的迟滞特性。通过对止口接触面的变形-滑移机理分析,使用一个詹金斯单元和一个弹簧单元并联模拟法兰的一个扇区,并基于法兰弯曲变形时每个扇区的不同状态建立了整个法兰结构的弯曲刚度简化模型,并对该简化模型进行了仿真,该简化模型能够较准确地模拟带止口法兰连接结构的刚度特性。基于简化模型和梁单元建立了简化转子结构模型,分析了带有止口的法兰连接结构对转子稳态动力学响应的影响。结果表明带有止口的法兰连接结构的迟滞特性能够影响峰值频率,随着止口过盈量的增加,响应峰值显著降低,具有较好的振动抑制效果。      

基于伴随方法的单级低速压气机气动设计优化

采用梯度方法对某型4.5级压气机最后级进行气动设计优化研究，梯度由连续伴随方法计算确定，多排伴随方程采用伴随掺混面模型进行数值求解。首先，采用基于经验修正的初步设计方法设计带进口导叶的4.5级低速、低压缩比压气机的原始气动外形。之后，在压气机近失速工况对最后级静子叶片进行伴随气动设计优化，通过优化叶型和安装角降低流动损失，目标函数定义为加权求和形式的熵增和流量偏差，优化中对流量进行约束。最后，开展基于伴随方法的多工况气动设计优化研究，改善两个不同转速条件下最后级的气动性能。优化结果表明，基于伴随方法的多排气动设计优化可以通过改变叶片气动外形提升多排全工况气动性能。     

Electrochemical micromachining of micro-dimple arrays on cylindrical inner surfaces using a dry-film photoresist

The application of surface textures has been employed to improve the tribological performance of various mechanical components. Various techniques have been used for the application of surface textures such as micro-dimple arrays, but the fabrication of such arrays on cylindrical inner surfaces remains a challenge. In this study, a dry-film photoresist is used as a mask during through-mask electrochemical micromachining to successfully prepare micro-dimple arrays with dimples 94 lm in diameter and 22.7 lm deep on cylindrical inner surfaces, with a machining time of 9 s and an applied voltage of 8 V. The versatility of this method is demonstrated, as are its potential low cost and high efficiency. It is also shown that for a fixed dimple depth, a smaller dimple diameter can be obtained using a combination of lower current density and longer machining time in a passivating sodium nitrate electrolyte.     

二元非线性机翼随机动力学行为

 为考查在高斯白噪声作用下二元机翼随机颤振动力学行为,采用数值仿真的方法对其进行了研究。首先把机翼简化成一个具有扭转和上下自由度的平板,其中扭转弹簧具有3次非线性刚度,同时假设空气是线性不可压的而且气动力是定常的,再对任意运动和高斯白噪声作用下的机翼进行建模。其次采用了蒙特卡罗仿真来求解随机微分方程的数值解,根据数值解结果进行统计分析,计算出最大Lyapunov指数。最后得出：在随机激励作用下机翼的动力学行为与确定性颤振相比有很大差异,同时随机颤振点提前于确定性颤振点。     

机翼对自转旋翼机纵向稳定性的影响

为了研究机翼对自转旋翼机纵向稳定性的影响,针对某复合式自转旋翼机,建立了基于状态空间法描述的非线性全量方程数学模型。该模型包含自转旋翼、机身、螺旋桨、机翼和尾翼的气动模型、动态入流模型和稳定性分析模型。运用该模型对比研究了样例自转旋翼机和样例复合式自转旋翼机的纵向稳定性。研究结果表明：机翼的增加对于浮沉模态和短周期模态稳定性是有利的;对于旋翼转速模态稳定性是不利的,在设计复合式自转旋翼机时可以考虑增加旋翼桨尖配重来提高此模态的稳定性。机翼的纵向位置对自转旋翼机的纵向稳定性有显著影响。在机翼纵向位置能满足配平约束条件下,机翼纵向位置越靠后,迎角稳定性越好,但旋翼转速稳定性越差。在设计复合式自转旋翼机时,机翼纵向位置的选择要综合考虑这两个因素进行折中。     

隐身外形飞行器用埋入式进气道的设计与风洞实验研究

本文为隐身外形飞行器用埋入式进气道发展了一套设计方法。该方法的理论基础是埋入式进气道进气机理和气动S弯概念,其关键技术包含通道中心线设计、横截面面积变化规律设计以及横截面形状设计等,各技术可以方便地用数学方法加以描述,整个方法易于编程实现。并结合一种隐身外形无人机提出了埋入式进气道方案,通过实验得到了此类隐身外形飞行器用埋入式进气道的气动特性。结果表明,所提出的埋入式进气道方案可行,所设计的模型进气道性能良好,所发展的设计方法合理。同时验证了埋入式进气道进气机理的正确性,也表明隐身外形飞行器与埋入式进气道的组合方案具有十分光明的应用前景。     

一个面向可变形模型实时有效的接触反馈框架

由于力反馈需要很高的计算速度及变形反馈需要详细的图形信息 ,本文提供一个实时有效的接触反馈框架 ,通过在粗糙三角形网格上进行局部细分来实现。当检测到接触后 ,将发生碰撞的表面细分以产生一个粒子系统。利用此粒子系统 ,用近似速度锥理论对形变进行模拟。同时 ,采用弹簧 -阻尼模型计算形变力。最后 ,对此框架进行了测试并实际应用于一个医疗规化仿真系统。     

基于PC2B格式自由尾迹方法的旋翼响应特性分析

旋翼自由尾迹模型的建模和桨叶动态响应计算的问题是直升机空气动力学领域中富有关键意义的课题。本文结合桨叶气动模型、旋翼涡尾迹模型、桨叶挥舞动力学模型、"PC2B"尾迹求解算法和旋翼配平模型,建立了一个时间精确的旋翼自由尾迹和桨叶动态气动响应的分析方法,并针对旋翼总距突增时的旋翼载荷和桨叶动态响应进行了计算和分析,得出了一些有意义的结果。     

局部凹槽对高超声速边界层中第二模态扰动演化的影响

采用直接数值模拟方法研究了局部矩形凹槽对来流马赫数为6.0的高超声速平板边界层中第二模态扰动演化的影响。引入了透射系数(定义为凹槽下游与上游扰动渐近幅值的比率)来量化凹槽的局部散射效应。数值结果表明:对于较浅的凹槽,频率较低的第二模态扰动被促进,而高频扰动的规律相反。对于大多数情况,凹槽深度的增加使得透射系数减小,这表明凹槽对扰动的促进作用减弱或抑制作用增强。当凹槽的深度超过某一临界值时,透射系数与凹槽深度的关系变为正相关,这表明了另一机制的出现。临界深度受扰动的频率影响:频率越低,临界深度越大。