Klobuchar模型的实用分析与改进

电离层延迟误差是无线电信号传播中不可忽视的误差源.GPS特许用户利用双频接收机的双频观测值直接对电离层延迟进行实时测定,其所得结果精度很高.多数普通用户所使用的单频接收机依靠电离层模型对其进行误差修正,效果不很理想.本文通过WUHN观测站双频接收机10天的实测数据对GPS广播星历采用的Klobuchar模型进行了验证,其结果与前人论述相一致.此外,经由反映太阳活动强度的太阳相对黑子数对Klobuchar模型提出了新的改进方法.实验数据结果表明,该方法对此模型修正效果有大幅提升,对原模型修正效果>50%的修正率由60%左右提升至85%以上,>80%的修正率由10%左右提升至40%以上.在实际应用中单频接收机用户可以参考本文改进方法对Klobuchar模型进行修正.      

GPS data processing of networks with mixed single- and dual-frequency receivers for deformation monitoring

In order to obtain crustal deformations of higher spatial resolution, existing GPS networks must be densified. This densification can be carried out using single-frequency receivers at moderate costs. However, ionospheric delay handling is required in the data processing. We adapt the Satellite-specific Epoch-differenced Ionospheric Delay model (SEID) for GPS networks with mixed single- and dual-frequency receivers. The SEID model is modified to utilize the observations from the three nearest dual-frequency reference stations in order to avoid contaminations from more remote stations. As data of only three stations are used, an efficient missing data constructing approach with polynomial fitting is implemented to minimize data losses. Data from large scale reference networks extended with single-frequency receivers can now be processed, based on the adapted SEID model. A new data processing scheme is developed in order to make use of existing GPS data processing software packages without any modifications. This processing scheme is evaluated using a sub-network of the German SAPOS network. The results verify that the new scheme provides an efficient way to densify existing GPS networks with single-frequency receivers.     

The use of ionospheric tomography and elevation masks to reduce the overall error in single-frequency GPS timing applications

Signals from Global Positioning System (GPS) satellites at the horizon or at low elevations are often excluded from a GPS solution because they experience considerable ionospheric delays and multipath effects. Their exclusion can degrade the overall satellite geometry for the calculations, resulting in greater errors; an effect known as the Dilution of Precision (DOP). In contrast, signals from high elevation satellites experience less ionospheric delays and multipath effects. The aim is to find a balance in the choice of elevation mask, to reduce the propagation delays and multipath whilst maintaining good satellite geometry, and to use tomography to correct for the ionosphere and thus improve single-frequency GPS timing accuracy. GPS data, collected from a global network of dual-frequency GPS receivers, have been used to produce four GPS timing solutions, each with a different ionospheric compensation technique. One solution uses a 4D tomographic algorithm, Multi-Instrument Data Analysis System (MIDAS), to compensate for the ionospheric delay. Maps of ionospheric electron density are produced and used to correct the single-frequency pseudorange observations. This method is compared to a dual-frequency solution and two other single-frequency solutions: one does not include any ionospheric compensation and the other uses the broadcast Klobuchar model. Data from the solar maximum year 2002 and October 2003 have been investigated to display results when the ionospheric delays are large and variable. The study focuses on Europe and results are produced for the chosen test site, VILL (Villafranca, Spain). The effects of excluding all of the GPS satellites below various elevation masks, ranging from 5° to 40°, on timing solutions for fixed (static) and mobile (moving) situations are presented. The greatest timing accuracies when using the fixed GPS receiver technique are obtained by using a 40° mask, rather than a 5° mask. The mobile GPS timing solutions are most accurate when satellites at lower elevations continue to be included: using a mask between 10° and 20°. MIDAS offers the most accurate and least variable single-frequency timing solution and accuracies to within 10 ns are achieved for fixed GPS receiver situations. Future improvements are anticipated by combining both GPS and Galileo data towards computing a timing solution.     

Ionospheric path delay models for spaceborne GPS receivers flying in formation with large baselines

GPS relative navigation filters could benefit notably from an accurate modeling of the ionospheric delays, especially over large baselines (>100 km) where double difference delays can be higher than several carrier wavelengths. This paper analyzes the capability of ionospheric path delay models proposed for spaceborne GPS receivers in predicting both zero-difference and double difference ionospheric delays. We specifically refer to relatively simple ionospheric models, which are suitable for real-time filtering schemes. Specifically, two ionospheric delay models are evaluated, one assuming an isotropic electron density and the other considering the effect on the electron density of the Sun aspect angle. The prediction capability of these models is investigated by comparing predicted ionospheric delays with measured ones on real flight data from the Gravity Recovery and Climate Experiment mission, in which two satellites fly separated of more than 200 km. Results demonstrate that both models exhibit a correlation in the excess of 80% between predicted and measured double-difference ionospheric delays. Despite its higher simplicity, the isotropic model performs better than the model including the Sun effect, being able to predict double differenced delays with accuracy smaller than the carrier wavelength in most cases. The model is thus fit for supporting integer ambiguity fixing in real-time filters for relative navigation over large baselines. Concerning zero-difference ionospheric delays, results demonstrate that delays predicted by the isotropic model are highly correlated (around 90%) with those estimated using GPS measurements. However, the difference between predicted and measured delays has a root mean square error in the excess of 30 cm. Thus, the zero-difference ionospheric delays model is not likely to be an alternative to methods exploiting carrier-phase observables for cancelling out the ionosphere contribution in single-frequency absolute navigation filters.     

Rapid local ionosphere modeling based on Precise Point Positioning over Iran: A case study under 2014 solar maximum

Presently, the ionosphere effect is the main source of the error in the Global Positioning System (GPS) observations. This effect can largely be removed by using the two-frequency measurements, while to obtain the reasonable results in the single-frequency applications, an accurate ionosphere model is required. Since the global ionosphere models do not meet our needs everywhere, the local ionosphere models are developed. In this paper, a rapid local ionosphere model over Iran is presented. For this purpose, the GPS observations obtained from 40 GPS stations of the Iranian Permanent GPS Network (IPGN) and 16 other GPS stations around Iran have been used. The observations have been selected under 2014 solar maximum, from the days 058, 107, 188 and 271 of the year 2014 with different geomagnetic activities. Moreover, ionospheric observables based on the precise point positioning (PPP) have been applied to model the ionosphere. To represent our ionosphere model, the B-spline basis functions have been employed and the variance component estimation (VCE) method has been used to regularize the problem.To show the efficiency our PPP-derived local ionosphere model with respect to the International GNSS Service (IGS) global models, these models are applied on the single point positioning using single-frequency observations and their results are compared with the precise coordinates obtained from the double-differenced solution using dual-frequency observations. The results show that the 95th percentile of horizontal and vertical positioning errors of the single-frequency point positioning are about 3.1 and 13.6?m, respectively, when any ionosphere model are not applied. These values significantly improve when the ionosphere models are applied in the solutions. Applying CODE’s Rapid Global ionosphere map (CORG), improvements of 59% and 81% in horizontal and vertical components are observed. These values for the IGS Global ionosphere map (IGSG) are 70% and 82%, respectively. The best results are obtained from our local ionosphere model, where 84% and 87% improvements in horizontal and vertical components are observed. These results confirm the efficiency of our local ionosphere model over Iran with respect to the global models. As a by-product, the Differential Code Biases (DCBs) of the receivers are also estimated. In this line, we found that the intra-day variations of the receiver DCBs could be significant. Therefore, these variations must be taken into account for the precise ionosphere modeling.     

A MARS-based method for estimating regional 2-D ionospheric VTEC and receiver differential code bias

The geometry-free linear combination of dual-frequency GNSS reference station ground observations are currently used to build the Vertical Total Electron Content (VTEC) model of the ionosphere. As it is known, besides ionospheric delays, there are differential code bias (DCB) of satellite (SDCB) and receiver (RDCB) in the geometry-free observation equation. The SDCB can be obtained using the International GNSS Service (IGS) analysis centers, but the RDCB for regional and local network receivers are not provided. Therefore, estimating the RDCB and VTEC model accurately and simultaneously is a critical factor investigated by researchers. This study uses Multivariate Adaptive Regression Splines (MARS) to estimate the VTEC approximate model and then substitutes this model in the observation equation to form the normal equation. The least squares method is used to solve the RDCB and VTEC model together. The research findings show that this method has good modeling effectiveness and the estimated RDCB has good reliability. The estimated VTEC model applied to GPS single-frequency precise point positioning has better positioning accuracy in comparison to the IGS global ionosphere map (GIM).     

基于RTK-GPS的提梁机组协调控制系统设计

双提梁机组协调控制系统利用对称布置的双频载波相位RTK-GPS(Real-Time Kinematic difference Global Position System )接收机完成对提梁机位置、航向位姿信息的测量,通过卡尔曼滤波与里程计融合,消除坐标定位信息的波动,提高位姿测定的精度;单机采用基于CAN (Controller Area Network)总线的网络控制系统,机组间数据传输采用无线网络,构成混合网络控制系统;采用基于双闭环的同步控制策略实现对两提梁机的同步协调控制.实际应用结果表明,两提梁机间相对位置偏差不超过0.1m,相对航向角度偏差不超过0.1°.      

Evaluation of COMPASS ionospheric model in GNSS positioning

As important products of GNSS navigation message, ionospheric delay model parameters are broadcasted for single-frequency users to improve their positioning accuracy. GPS provides daily Klobuchar ionospheric model parameters based on geomagnetic reference frame, while the regional satellite navigation system of China’s COMPASS broadcasts an eight-parameter ionospheric model, COMPASS Ionospheric Model(CIM), which was generated by processing data from continuous monitoring stations, with updating the parameters every 2 h. To evaluate its performance, CIM predictions are compared to ionospheric delay measurements, along with GPS positioning accuracy comparisons. Real observed data analysis indicates that CIM provides higher correction precision in middle-latitude regions, but relatively lower correction precision for low-latitude regions where the ionosphere has much higher variability. CIM errors for some users show a common bias for in-coming COMPASS signals from different satellites, and hence ionospheric model errors are somehow translated into the receivers’ clock error estimation. In addition, the CIM from the China regional monitoring network are further evaluated for global ionospheric corrections. Results show that in the Northern Hemisphere areas including Asia, Europe and North America, the three-dimensional positioning accuracy using the CIM for ionospheric delay corrections is improved by 7.8%–35.3% when compared to GPS single-frequency positioning ionospheric delay corrections using the Klobuchar model. However, the positioning accuracy in the Southern Hemisphere is degraded due apparently to the lack of monitoring stations there.     

Multi-GNSS contributions to differential code biases determination and regional ionospheric modeling in China

Due to the limited number and uneven distribution globally of Beidou Satellite System (BDS) stations, the contributions of BDS to global ionosphere modeling is still not significant. In order to give a more realistic evaluation of the ability for BDS in ionosphere monitoring and multi-GNSS contributions to the performance of Differential Code Biases (DCBs) determination and ionosphere modeling, we select 22 stations from Crustal Movement Observation Network of China (CMONOC) to assess the result of regional ionospheric model and DCBs estimates over China where the visible satellites and monitoring stations for BDS are comparable to those of GPS/GLONASS. Note that all the 22 stations can track the dual- and triple-frequency GPS, GLONASS, and BDS observations. In this study, seven solutions, i.e., GPS-only (G), GLONASS-only (R), BDS-only (C), GPS + BDS (GC), GPS + GLONASS (GR), GLONASS + BDS (RC), GPS + GLONASS + BDS (GRC), are used to test the regional ionosphere modeling over the experimental area. Moreover, the performances of them using single-frequency precise point positioning (SF-PPP) method are presented. The experimental results indicate that BDS has the same ionospheric monitoring capability as GPS and GLONASS. Meanwhile, multi-GNSS observations can significantly improve the accuracy of the regional ionospheric models compared with that of GPS-only or GLONASS-only or BDS-only, especially over the edge of the tested region which the accuracy of the model is improved by reducing the RMS of the maximum differences from 5–15 to 2–3 TECu. For satellite DCBs estimates of different systems, the accuracy of them can be improved significantly after combining different system observations, which is improved by reducing the STD of GPS satellite DCB from 0.243 to 0.213, 0.172, and 0.165 ns after adding R, C, and RC observations respectively, with an increment of about 12.3%, 29.4%, and 32.2%. The STD of GLONASS satellite DCB improved from 0.353 to 0.304, 0.271, and 0.243 ns after adding G, C, and GC observations, respectively. The STD of BDS satellite DCB reduced from 0.265 to 0.237, 0.237 and 0.229 ns with the addition of G, R and GR systems respectively, and increased by 10.6%, 10.4%, and 13.6%. From the experimental positioning result, it can be seen that the regional ionospheric models with multi-GNSS observations are better than that with a single satellite system model.     

基于空间统计方法的电离层折射修正技术

针对中国上空电离层所具有的特殊性和GPS观测站在中国西部分布相对稀疏的特点, 尝试探索中国卫星增强系统电离层时延信息修正技术, 为卫星导航定位以及遥感、遥测等空间应用工程的电波修正提供数据. 利用中国地壳形变监测网提供的双频GPS数据, 以空间统计方法为主要工具, 给出了普通Kriging电离层估计算法, 构建了平静期和磁暴期电离层理论变异模型, 详细分析了电离层折射修正的精度. 结果表明, 将空间统计方法应用于卫星增强系统中的电离层时延改正问题, 有利于提高增强系统的电离层折射修正精度, 特别是在观测样点相对较少的情况下, 有利于系统完整性的实现.      

WAAS系统中电离层折射校正的新方法及计算结果

电离层介质的色散性是影响电磁波信号进行卫星导航定位精度的重要因素之一.配合北斗二代分系绩研制任务,提出了一种新的电离层折射校正算法,并利用2000年7月1日到3日的双频GPS观测数据对6个用户站进行试算,进一步将试算所得均方根误差和电离层网格算法得到的误差进行比较.结果表明,对于中纬区域的用户站,估算的TEC误差约为0.5 m左右;而低纬用户误差相对增大,为1 m左右.文中给出的算法与电离层网格模型所提供的精度相差不多,在未来中国自主的卫星增强系统中采用新方法进行电离层进行修正是可行的及有效的.      

Demonstration of the use of the Doppler Orbitography and Radio positioning Integrated by Satellite (DORIS) measurements to validate GPS ionospheric imaging

There is a lack of independent ionospheric data that can be used to validate GPS imaging results at mid latitudes over severe storm times. Doppler Orbitography and Radio positioning Integrated by Satellite (DORIS), a global network of dual-frequency ground to satellite observations, provides this missing data and here is employed as verification to show the accuracy of the ionospheric GPS images in terms of the total electron content (TEC). In this paper, the large-scale ionospheric structures that appeared during the strong geomagnetic storm of 20 November 2003 are reconstructed with a GPS tomographic algorithm, known as MIDAS, and validated with DORIS TEC measurements. The main trough shown in an extreme equatorward position in the ionospheric imaging over mainland Europe is confirmed by DORIS satellite measurements. Throughout the disturbed day, the variations of relative slant TECs between DORIS data and MIDAS results agree quite well, with the average of the mean differences about 2 TECu. We conclude that as a valuable supplement to GPS data, DORIS ionospheric measurements can be used to analyse TEC variations with a relatively high resolution, ∼10 s in time and tens of kilometres in space. This will be very helpful for identification of some highly dynamic structures in the ionosphere found at mid-latitudes, such as the main trough, TID (Travelling Ionospheric Disturbances) and SED (Storm Enhanced Density), and could be used as a valuable auxiliary data source in ionospheric imaging.     

An improved approach to model regional ionosphere and accelerate convergence for precise point positioning

Given the severe effects of the ionosphere on global navigation satellite system (GNSS) signals, single-frequency (SF) precise point positioning (PPP) users can only achieve decimeter-level positioning results. Ionosphere-free combinations can eliminate the majority of ionospheric delay, but increase observation noise and slow down dual-frequency (DF) PPP convergence. In this paper, we develop a regional ionosphere modeling and rapid convergence approach to improve SF PPP (SFPPP) accuracy and accelerate DF PPP (DFPPP) convergence speed. Instead of area model, ionospheric delay is modeled for each satellite to be used as a priori correction. With the ionospheric, wide-lane uncalibrated phase delay (UPD) and residuals satellite DCBs product, the wide-lane observations for DF users change to be high-precision pseudorange observations. The validation of a continuously operating reference station (CORS) network was analyzed. The experimental results confirm that the approach considerably improves the accuracy of SFPPP. For DF users, convergence time is substantially reduced.     

Calibration errors in determining slant Total Electron Content (TEC) from multi-GNSS data

The global navigation satellite system (GNSS) is presently a powerful tool for sensing the Earth's ionosphere. For this purpose, the ionospheric measurements (IMs), which are by definition slant total electron content biased by satellite and receiver differential code biases (DCBs), need to be first extracted from GNSS data and then used as inputs for further ionospheric representations such as tomography. By using the customary phase-to-code leveling procedure, this research comparatively evaluates the calibration errors on experimental IMs obtained from three GNSS, namely the US Global Positioning System (GPS), the Chinese BeiDou Navigation Satellite System (BDS), and the European Galileo. On the basis of ten days of dual-frequency, triple-GNSS observations collected from eight co-located ground receivers that independently form short-baselines and zero-baselines, the IMs are determined for each receiver for all tracked satellites and then for each satellite differenced for each baseline to evaluate their calibration errors. As first derived from the short-baseline analysis, the effects of calibration errors on IMs range, in total electron content units, from 1.58 to 2.16, 0.70 to 1.87, and 1.13 to 1.56 for GPS, Galileo, and BDS, respectively. Additionally, for short-baseline experiment, it is shown that the code multipath effect accounts for their main budget. Sidereal periodicity is found in single-differenced (SD) IMs for GPS and BDS geostationary satellites, and the correlation of SD IMs over two consecutive days achieves the maximum value when the time tag is around 4?min. Moreover, as byproducts of zero-baseline analysis, daily between-receiver DCBs for GPS are subject to more significant intra-day variations than those for BDS and Galileo.     

Fast calibration of between-receiver GPS/Galileo/BDS differential phase bias with millimeter accuracy based on short baseline mode

The differential code and phase biases induced by the receiver hardware (including receiver, antenna, firmware, etc.) of the Global Navigation Satellite System (GNSS) have significant effects on precise timing and ionosphere sensing, thus deserve careful treatment. In this contribution, we propose an approach to fast fix the single-difference ambiguity to finally obtain the unbiased estimates of between-receiver differential phase bias (BR-DPB) and between-receiver differential code-phase bias (BR-DCPB) based on the short baseline mode. The key to this method is that the error sources can be significantly eliminated due to the length of the baseline is very short. At the same time, the empirical constraints and random characteristics of BR-DPB/BR-DCPB were considered, which is conducive to the resolution of single-difference ambiguity. Several sets of GNSS data (GPS L1/L2, Galileo E1/E5b, and BDS B1/B3), recorded by the short baselines in an interval of 30 s and covered a broad range of receiver/antenna types (JAVA, SEPT, LEIC, and TRIM), were used to verify the effectiveness of the proposed method. The numerical tests show that the proposed method is capable of fast fixing the single-difference ambiguity successfully within a few epochs and then providing the unbiased estimates of BR-DPB and BR-DCPB in an epoch-by-epoch manner. Experiments show that the estimated BR-DPB is in millimeter accuracy, which is of great significance for the millimeter-accuracy phase time transfer and ionospheric delay estimation. Furthermore, the calibrated BR-DPB/BR-DCPB can be treated as the known products for long-distance precise timing and ionosphere sensing based on the inter-station single-difference model.     

基于双频GPS观测的电离层TEC与硬件延迟反演方法

利用全球定位系统（Global Positioning System,GPS）的双频观测数据反演得到电离层的总电子含量（Total Electron Content,TEC）,使得广域甚至全球范围高时空分辨率的电离层观测研究成为可能,但由于GPS卫星和接收机对信号的硬件延迟可导致TEC测量系统偏差,因此,需要探索反演TEC并估测GPS卫星与接收机硬件延迟的有效算法.本文根据电离层电波传播理论,阐述了基于双频GPS观测提取电离层TEC的方法,给出TEC与硬件延迟的基本关系.综合研究了TEC与硬件延迟的反演方法,进行分析与归纳分类,在此基础上提出了有待深入研究的问题.      

NeQuick G model based scale factor determination for using SBAS ionosphere corrections at low earth orbit

A space-based augmentation system (SBAS) provides real-time correction data for global navigation satellite system (GNSS) users near ground. In order to use the SBAS ionosphere correction for low Earth orbit (LEO) satellites, the correction should be scaled down for the LEO altitude. This scale factor varies with ionosphere distribution and it is hard to determine the value at LEO in real time. We propose a real-time scale factor determination method by using Galileo GNSS’s NeQuick G model. A LEO satellite GPS data and SBAS data received on ground were used to evaluate the performance of the NeQuick G derived variable scale factor. The NeQuick G derived scale factor shows a significant accuracy improvement over NeQuick G model or pre-determined constant scale factor. It improves a vertical positioning accuracy of the LEO satellite. The error mean reductions of the vertical positioning over NeQuick G and the constant scale factor are 31.5% and 11.7%, respectively.     

The investigation of the ionospheric variability by the radiotranslucence method

To provide a continuous single-point sounding of a large-scale region of the ionosphere the translucence method of studying the ionosphere utilizing satellite navigation system signals has been used. Simultaneous receiving the signals of GPS Navstar and GLONASS from different azimuths gives information on variations of the ionosphere in almost real time. Using measured data the reconstruction of the electron density profiles in the regions of intersection of a sounding ray with the ionosphere has been carried out. The translucence method was used to investigate the ionosphere effects of a partial solar eclipse (PSE) that occurred on 11.08 1999 by probing of the ionosphere with different GPS system signals in the Zwenigorod region.     

Electron density retrieval from occulting GNSS signals using a gradient-aided inversion technique

In the coming years, opportunities for remote sensing of electron density in the Earth’s ionosphere will expand with the advent of Galileo, which will become part of the global navigation satellite system (GNSS). Methods for accurate electron density retrieval from radio occultation data continue to improve. We describe a new method of electron density retrieval using total electron content measurements obtained in low Earth orbit. This method can be applied to data from dual-frequency receivers tracking the GPS or Galileo transmitters. This simulation study demonstrates that the method significantly improves retrieval accuracy compared to the standard Abel inversion approach that assumes a spherically symmetric ionosphere. Our method incorporates horizontal gradient information available from global maps of Total Electron Content (TEC), which are available from the International GNSS Service (IGS) on a routine basis. The combination of ground and space measurements allows us to improve the accuracy of electron density profiles near the occultation tangent point in the E and F regions of the ionosphere.     

基于单频星载GPS数据的低轨卫星精密定轨

为满足搭载单频GPS接收机低轨卫星的精密定轨需求以及深化单频定轨研究,文中解决了单频星载GPS数据的周跳探测问题,并利用“海洋二号”（HY-2A）卫星及“资源三号”（ZY-3）卫星的单频星载GPS实测数据采用两种方法确定了二者的简化动力学轨道,并通过观测值残差分析、与双频精密轨道比较、激光测卫数据检核等方法对所得轨道精度进行评定。结果表明,在不考虑电离层延迟影响的情况下,HY-2A卫星定轨精度为2~3dm,ZY-3卫星为1m左右;而采用半和改正组合消除电离层延迟一阶项影响后,二者定轨精度均显著提高,HY-2A卫星三维精度提高至1dm左右,ZY-3卫星提高至1~2dm。文章的研究成果表明,搭载单频GPS接收机的低轨卫星也可获得厘米级的定轨精度。