基于TMS320C6713B的远程软件加载设计与实现

针对以TMS320C6713B为核心的某嵌入式系统要求通过RS422/485进行系统应用软件的加载与固化,摆脱JTAG口调试电缆的长度限制的问题,描述了一种采用RS422/485进行软件加载与BOOTLOAD的设计方法,从硬件设计、软件设计两大方面说明基于C6713B的远程软件加载系统的实现,对TMS320C6713B使用DSP/BIOS配置、EMIF总线外挂大容量SDRAM等一些新特点进行软件加载系统的设计,从而满足了嵌入式系统对远程加载软件大数据量,快速传输的要求.     

TMS320C6678多核DSP的加载配置和实现方法

程序代码正确的固化加载运行是多核DSP应用的前提和基础.简要介绍了DSP的加载器和加载过程,阐述了多核处理器件的加载配置管理方法.以TI公司的多核DSP TMS320C6678为例,介绍了多核DSP的加载模式和流程,详细阐述了EMIF16的Nor FLASH加载实现方法,可以实现多核DSP软件的正确、可靠加载运行.     

TI6678多核DSP以太网接口的设计与实现

DSP的以太网接口在信号处理设计中应用的越来越广泛.介绍了TI6678多核DSP以太网控制器的内部结构和工作原理,给出了DSP以太网接口的硬件电路设计方案和软件开发流程.结合应用需求,介绍了基于以太网远程加载的应用实例,为TMS320 C6000系列DSP的以太网接口设计提供了参考.     

基于DSP的导引控制器硬件设计与实现

按照小型化、高实时性的要求,采用TI公司面向控制的DSP芯片TMS320LF2407A,设计并实现了以DSP为处理核心的导引控制器,详细介绍了系统的整体方案设计和具体的硬件选型及接口设计。重点论述了飞控计算机与导引控制器之间的串行通信设计,并给出了硬件接口电路。     

基于CPLD的TMS320C6727B外设重叠地址空间解析方法的研究与实现

针对TMS320C6727B扩展外设无法基于其硬件资源直接访问的问题，提出了一种重叠地址解析的外设扩展方法，可满足多个外设、外设多个寄存器或端口地址的访问控制。对外设地址空间构成解析、地址映射CPLD的逻辑控制、用户程序中外设寄存器或端口的访问控制等问题，进行了详细的研究分析，并给出了寄存器或端口逻辑控制和用户程序访问的实现方法。硬件平台测试验证了利用重叠地址解析实现外设访问控制方法的可行性。     

基于1553B总线的惯导系统终端设计

为了适应惯导系统数据传输的实时性和可靠性的需求,本文提出了基于1553B总线的惯导系统数据采集和传输方案.文章描述了1553B总线终端接口芯片BU-61580的内部寄存器和RAM资源,提出了BU-61580与TMS320F206 DSP芯片的硬件接口设计和软件接口设计方案.实现了1553B终端RT与总线控制器BC之间的...     

IDE接口电子盘实时记录模块的设计和实现

介绍一种采用DSP（TMS320F2812）,IDE接口的电子盘和具有I^2C总线接口的计时器来实现实时数据记录功能的模块设计方案。该设计直接以扇区的物理地址对电子盘扇区进行读写操作。     

采用TMS320C6201实现数字式脉冲压缩雷达实时信号处理

简述了雷达信号脉冲压缩的几种实现方法，着重讨论了数字式脉冲压缩的特点及其信号处理方法；分析了所选择的TMS320C6XEVM信号处理板的接口实现；给出了基于TMS320C6X的信号处理系统软硬件的设计。由于采用高速数字信号处理器件进行脉冲压缩，使得软件设计具有很大的灵活性。     

基于TMS320F28335 的一种多机多通道通讯方法的设计

TMS320F28335 是TI 公司的一款数字信号处理芯片，具备丰富的外设接口，器件可靠性强，在机载 机电、接口、控制领域得到应用。面对嵌入式控制器多机通讯的需求，使用TMS320F28335 的McBSP 接口和 DMA 功能设计一种时分复用的多机多通道通讯方法，硬件接口直连，软件通过DMA 自动完成帧数据收发， 避免通讯对DSP 内核的占用，实现一种经济、可靠的多机通讯方案。     

某弹载计算机GJB1188A接口的设计与实现

栽机要求悬挂物必须实现GJB1188A中数据总线(GJB289A)的远程终端(RT)功能,同时实现GJB1188A中任务悬挂物投放允许等接口功能.描述了一种采用TMS320C6713B高速浮点DSP为核心的GJB1188A接口的实现方法,从硬件平台组成、控制逻辑实现、驱动软件结构三个方面来说明GJB289A(RT)功能的实现方法.介绍了任务悬挂物投放允许等接口的一种设计实现方法.从而将以往单一的GJB289A总线接口模块与嵌入式计算机结合在一起.满足了体积和成本上的要求.使嵌入式弹载计算机在GJB1188A接口的前提下实现与机载火控系统的通信、进行同步的数据采集与控制.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.