Vertical sounding balloons for stratospheric photochemistry

Vertical sounding balloons are unique tools for stratospheric photochemistry investigations. An example of the use of a vertically piloted gas balloon for nitrogen dioxide diurnal variation search is presented. Improvements of such a method with the use of montgolfieres (hot air balloons) are proposed.     

Balloon materials and designs

Improvements of materials can extend the performance of scientific balloon flights in altitude, suspended load and duration. The impact of new materials is considered in the design of superpressure balloons for long duration improvement, ultra light weight for sounding balloons, and a launch technique for minimizing relative wind problems.     

Launching of a 500,000 cubic meter balloon with the semi-dynamic launching method

Launching a large balloon in a limited launching field is a long standing problem in Japan. The largest balloon ever launched successfully was 200,000 m³ in volume. It was launched in 1973. A larger balloon with a volume of 500,000 m³ was tried later, but it burst during the ascending phase. For launching balloons with a large lift exceeding 500 kg, the conventional static launching method had the most serious problem with possible damage to the polyethylene film of the balloon caused by the holding mechanism. After that, we had developed a new static launching method to launch balloons with a total lift of 1.0 ton. For launching a large balloon with a total lift above 1.5 ton, the new static launching method had a weak point in that if there was an air bubble in the folded part of the balloon, it may puncture the balloon as it is pushed by a spool. To avoid this problem, we developed a semi-dynamic launching method in 1999 using a launcher fixed to the ground leaving a freedom of rotation around the vertical axis. We have launched some balloons using the method and have gradually enriched our experience in using this system.In 2003, we successfully launched a balloon with a volume of 500,000 m³ by using the method. This balloon was made of polyethylene films with a thickness of 20 μm and it is the largest balloon ever launched in Japan.     

Feasibility study of a sea-anchored stratospheric balloon for long-duration flights

Sea-anchored balloons are stratospheric super-pressure balloons that are anchored to the sea. The sea-anchored balloon is a simple system that has the capability for long-duration flights, fixed-point observations, flexible launch windows, easy telemetry links to ground stations, and quick recoveries. Such balloons are not required to fly through the jet stream while tethered to the ground or sea, because the tether is deployed from a reel on the balloon after reaching a floating altitude. In this study, the feasibility of the sea-anchored balloon is investigated, with particular emphasis on the tether strength, balloon altitude, and system mass, based on the present technological level of the tether’s specific strength. Although the wind distribution with altitude is a dominant factor for feasibility, a sea-anchored balloon with an altitude of about 25 km would be feasible if the velocity of the jet stream is sufficiently low. The sea-anchored balloon can be simply flight-tested, since additional ground facilities and special flight operations are not necessary.     

The high altitude student platform (HASP) for student-built payloads

An outstanding issue with aerospace workforce development is what should be done at the university level to attract and prepare undergraduates for an aerospace career. One approach adopted by many institutions is to lead students through the design and development of small payloads (less than about 500 grams) that can be carried up to high altitude (around 30 km) by a latex sounding balloon. This approach has been very successful in helping students to integrate their content knowledge with practical skills and to understand the end-to-end process of aerospace project development. Sounding balloons, however, are usually constrained in flight duration (∼30 min above 24 km) and payload weight, limiting the kinds investigations that are possible. Student built picosatellites, such as CubeSats, can be placed in low Earth orbit removing the flight duration constraint, but the delays between satellite development and launch can be years. Here, we present the inexpensive high altitude student platform (HASP) that is designed to carry at least eight student payloads at a time to an altitude of about 36 km with flight durations of 15–20 h using a small zero-pressure polyethylene film balloon. This platform provides a flight capability greater than sounding balloons and can be used to flight-test compact satellites, prototypes and other small payloads designed and built by students. The HASP includes a standard mechanical, power and communication interface for the student payload to simplify integration and allows the payloads to be fully exercised. HASP is lightweight, has simple mission requirements providing flexibility in the launch schedule, will provide a flight test opportunity at the end of each academic year.     

Properties of tandem balloons connected by extendable suspension wires

The tandem balloon system has been known as a candidate system for long duration flight balloons. In this paper, the properties of the system are analytically studied in a new way by introducing an extendable suspension wire in the Sky Anchor configuration, which consists of a zero-pressure main balloon suspending a payload and a super-pressure balloon suspended below the payload. It was found that extension of the suspension wire between the payload and the super-pressure balloon can extend the capability of the tandem system; the altitude of the zero-pressure balloon can be changed without any consumables except some energy, and the day–night oscillation of the balloon altitude can be suppressed. This property is useful as the vehicle for long duration flights. It is also pointed out that the method to control the altitude of a balloon using an additional suspended super-pressure balloon can also be applied for super-pressure balloons.     

A new balloon base in Japan

Since 1971, numerous balloons have been launched from the Japanese balloon base, the Sanriku Balloon Center (SBC). Through these years, balloon technologies have been developed continuously and many scientific achievements have resulted. Recently, however, because of the limited area of the launching pad of the SBC, we have been faced with the difficulty of safely launching large balloons. To solve this issue, we decided to move the balloon base from the SBC to the Taiki Aerospace Research Field (TARF) in northern Japan. The TARF had an existing huge hanger and a paved launch pad capable of being utilised for balloon operations. To evolve the TARF into a new balloon base, new balloon facilities have been constructed at the TARF and equipment was transferred from the SBC to the TARF during July 2007 and March 2008. The SBC was closed in September 2007, and the new base became operational in May 2008. The new base at the TARF is designed to launch larger balloons with greater safety and to perform balloon operations more effectively than ever before. In the summer of 2008, we carried out the first series of the balloon campaign at the TARF, and succeeded in two engineering flights of stratospheric balloons. By the success of these flights, we have verified that the whole system of the new balloon base is well established.     

Scientific ballooning in Japan – An over view of recent activities

Current status of scientific ballooning in Japan is reviewed. First, I describe successful application of balloon technologies to construct a vessel of transparent plastic film, to contain about 1000 tons of liquid scintillator in Kamioka Liquid Scintillator Anti-Neutrino Detector (KamLAND). KamLAND is a project to study neutrino oscillation phenomena, by detecting anti-neutrinos produced in distant nuclear reactors. Next, I describe high altitude balloons developed by the ISAS balloon group. They developed balloons made from ultra-thin polyethylene film, producing a balloon of volume 60,000 m³ which successfully reached an altitude of 53 km in 2002. This is a world record, the greatest altitude that a balloon has ever achieved. ISAS is applying further effort to develop balloons with even thinner films, to achieve a higher altitude than 53 km. Other recent activities by the ISAS balloon group are briefly described.I also review scientific ballooning projects now operating in Japan, particularly focusing on the Balloon-Borne Experiment with a Superconducting Spectrometer (BESS) program. This is a US–Japan collaborative program that has carried out very precise measurements of antiprotons, protons and other components in primary cosmic rays, as well as measuring the fluxes of atmospheric muons and other components. The results of these observations give us important information to improve our understanding of the production mechanism of antiprotons observed in the primary cosmic rays. The data are also important for analysis of atmospheric neutrino events observed by Super-Kamiokande and other ground-based neutrino detectors. Future prospects of BESS and other balloon-borne cosmic-ray research programs are also presented.     

Japanese polar patrol balloon experiments from 2002 to 2004

Polar patrol balloon experiments were carried out at Syowa Station in Antarctica from 2002 to 2004. Two balloons were launched for the purpose of observing phenomena in the polar atmosphere and one was done for the observation of high energy cosmic electrons. We developed a new housekeeping system including communication device using the Iridium satellite network, an auto-level controller driven by a new program for keeping the flight altitude, and a power management system for solar cells combined with secondary batteries.Two balloons for studying phenomena in the Antarctic atmosphere launched on January 13, 2003 made flights for 18 days and 25 days, respectively. All the housekeeping system worked well during the flights as we expected. Based on these experiments, we adjusted parameters for the altitude control system and the power management system. We launched a balloon for the cosmic electron observation on January 4, 2004. It flew 13 days around the Antarctica with the perfect operation of the onboard housekeeping system. We hope that fruitful scientific results will be obtained from these long-duration flights.     

后向台阶层流边界层分离实验研究

本文应用偏振差动式激光测速仪对后向台阶层流边界层分离、再附及发展为湍流边界层的整个过程进行了精细的量测,得到了时均速度、湍流强度等的分布特性。我们发现,在本实验条件下,层流边界层分离后在再附点处为过渡流,进一步发展最后形成湍流边界层。在湍流边界层区域,流速分布遵循对数律,但积分常数比平板湍流边界层中所得值要大。     

High altitude flights in equatorial regions

A thorough analysis of balloon flights made from Hyderabad, India (Latitude 17°28′N, Longitude 78°35′E), and other equatorial sites has been made. It has been shown that limited success is expected for flights made from equatorial latitudes with balloons made out of natural colour polyethylene film, since the best known balloon film in the world today viz. Winzen Stratofilm is tested for low temperature brittleness only at ?80°C., whereas the tropopause temperatures over equatorial latitudes vary between ?80°C and ?90°C. The success becomes even more critical when flights are made with heavy payloads and larger balloons particularly at night when in the absence of solar radiation the balloon film becomes more susceptible to low temperature brittle failure. It is recommended that in case of capped balloons longer caps should be used to fully cover the inflated protion of the balloon at the higher level equatorial tropopause. It is also advised that the conditions such as wind shears in the tropopause should be critically studied before launching and a day with the tropopause temperature nearer to ?80°C should be chosen. Special care also should be taken while handling the balloon on ground and during launching phase. Properties of Winzen Stratofilm have been critically studied and fresh mandates have been recommended on the basis of limiting values of film stresses which caused balloon failures in the equatorial tropopause. It is also emphasized that the data on such flights is still meagre especially for flights with heavy payloads and larger balloons. It has been also shown that it is safest to use balloons made out of grey coloured film which retains its flexibility with the absorption of solar radiation, the success obtained with such balloons so far being 100%. The drawback, however, is that these balloons cannot be used for night flights. Stratospheric wind regimes over Hyderabad are also discussed with a view to determine the period over which long duration flights can be made. The data available, however, is meagre and it is recommended that more frequent special wind ascents be made to collect adequate statistical data from which reliable conclusions could be drawn through critical analysis.     

Development of the High Altitude Student Platform

The High Altitude Student Platform (HASP) was originally conceived to provide student groups with access to the near-space environment for flight durations and experiment capabilities intermediate between what is possible with small sounding balloons and low Earth orbit rocket launches. HASP is designed to carry up to twelve student payloads to an altitude of about 36 km with flight durations of 15–20 h using a small zero-pressure polyethylene film balloon. This provides a flight capability that can be used to flight-test compact satellites, prototypes and other small payloads designed and built by students. HASP includes a standard mechanical, power and communication interface for the student payload to simplify integration and allows the payloads to be fully exercised. Over the last two years a partnership between the NASA Balloon Program Office (BPO), Columbia Scientific Balloon Facility (CSBF), Louisiana State University (LSU), the Louisiana Board of Regents (BoR), and the Louisiana Space Consortium (LaSPACE) has led to the development, construction and, finally, the first flight of HASP with a complement of eight student payloads on September 4, 2006. Here we discuss the primary as-built HASP systems and features, the student payload interface, HASP performance during the first flight and plans for continuing HASP flights. The HASP project maintains a website at http://laspace.lsu.edu/hasp/ where flight application, interface documentation and status information can be obtained.     

Scientific ballooning in Japan

Activities in scientific ballooning in Japan during 1998–1999 are reported. The total number of scientific balloons flown in Japan in 1998 and 1999 was sixteen, eight flights in each year. The scientific objectives were observations of high energy cosmic electrons, air samplings at various altitudes, monitoring of atmospheric ozone density, Galactic infrared observations, and test flights of new type balloons. Balloon expeditions were conducted in Antarctica by the National Institute of Polar Research, in Russia, in Canada and in India in collaboration with foreign countries' institutes to investigate cosmic rays, Galactic infrared radiation, and Earth's atmosphere. There were three flights in Antarctica, four flights in Russia, three flights in Canada and two flights in India. Four test balloons were flown for balloon technology, which included pumpkin-type super-pressure balloon and a balloon made with ultra-thin polyethylene film of 3.4 μm thickness.     

Mechanical properties of ANTRIX balloon film and fabrication of single cap large volume balloons

The zero pressure plastic balloons used for high altitude studies are generally made from polyethylene material. Tensile properties of the thin film polymer are the key parameters for material selection due to extremely low temperature of −90 °C encountered by the balloons in the tropopause region during the ascent at equatorial latitudes. The physical and structural properties of the material determine the uniformity of the stress distribution over the entire shell. Load stresses from the suspended load propagate via load tapes heat sealed along with the gore seals as per the balloon design. A balance between this heat seal strength and the film strength is a desirable property of the basic resin in terms of the bubble strength, gauge uniformity, and long-term storage properties. In addition, the design of the top shell of the balloon and its stress distribution play an important role since only a fraction of the balloon is deployed during the filling operation and the ascent. In this paper we describe the mechanical properties of the ‘ANTRIX’ film developed by us and the optimized design of single cap balloons, which have been successfully used in our experiments over the past 5 years.     

Initial estimates of Venus winds from ground-based radio tracking of the VEGA balloons

A global array of 20 radio observatories was used to measure the three-dimensional position and velocity of the two meteorological balloons that were injected into the equatorial region of the Venus atmosphere by the VEGA spacecraft. Initial analysis of only radial velocities indicates that each balloon was blown westward about 11,500 kilometers (8000 kilometers on the night side) by zonal winds with a mean speed of about 70 meters per second. Excursions of the data from a model of constant zonal velocity are generally less than 3 meters per second; however, a much larger variation is evident near the end of the flight of the second balloon. Consistent systematic trends in the residuals for both balloons indicate the possibility of a solar-fixed atmospheric feature.     

Performance simulation of high altitude scientific balloons

The design and operation of a high altitude scientific balloon requires adequate knowledge of the thermal characteristics of the balloon to make it safe and reliable. The thermal models and dynamic models of altitude scientific balloons are established in this paper. Based on the models, a simulation program is developed. The thermal performances of a super pressure balloon are simulated. The influence of film radiation property and clouds on balloon thermal behaviors is discussed in detail. The results are helpful for the design and operate of safe and reliable high altitude scientific balloons.     

Development overview of the revised NASA Ultra Long Duration Balloon

The desire for longer duration stratospheric flights at constant float altitudes for heavy payloads has been the focus of the development of the National Aeronautics and Space Administration’s (NASA) Ultra Long Duration Balloon (ULDB) effort. Recent efforts have focused on ground testing and analysis to understand the previously observed issue of balloon deployment. A revised approach to the pumpkin balloon design has been tested through ground testing of model balloons and through two test flights. The design approach does not require foreshortening, and will significantly reduce the balloon handling during manufacture reducing the chances of inducing damage to the envelope. Successful ground testing of model balloons lead to the fabrication and test flight of a ∼176,000 m³ (∼6.2 MCF – Million Cubic Foot) balloon. Pre-flight analytical predictions predicted that the proposed flight balloon design to be stable and should fully deploy. This paper provides an overview of this first test flight of the revised Ultra Long Duration Balloon design which was a short domestic test flight from Ft. Sumner, NM, USA. This balloon fully deployed, but developed a leak under pressurization. After an extensive investigation to the cause of the leak, a second test flight balloon was fabricated. This ∼176,000 m³ (∼6.2 MCF) balloon was flown from Kiruna, Sweden in June of 2006. Flight results for both test flights, including flight performance are presented.     

Ballooning activities in Japan

The Scientific Balloon Center of ISAS/JAXA has carried out two balloon campaigns at Sanriku, Iwate, Japan every year. Ten to twelve balloon vehicles are launched annually for scientific and engineering experiments. Since 2005, a Brazilian balloon campaign has also been conducted in cooperation with INPE. In the 2006 Brazilian campaign, large and heavy payloads up to 1500 kg for astronomy will be launched. New generation balloons, such as super-pressure balloons and high-altitude balloons with ultra-thin films, are being developed. The current status and prospect of the Japanese scientific ballooning are discussed.     

Uncertainties in the measurement of the atmospheric velocity due to balloon-gondola pendulum-like motions

Balloons lead to the highest vertical resolution of air velocity data actually attainable from atmospheric soundings. However, the pendulum-like motion of the balloon-gondola system may significantly affect these measurements if the distance between balloon and gondola is large. This may prevent the study of the highest vertical resolution range obtained. Also, if not appropriately discriminated, these fluctuations could be confused with small scale or turbulent oscillations of the atmosphere. It is shown from simple energy considerations that horizontal and vertical wind velocity perturbations introduced in the observations by the pendulum motion may usually be comparable to typical measurements. Vertical velocity data that were obtained with an instrumented gondola in a zero pressure balloon, which typically reach the lower stratosphere, are analyzed and found to be in agreement with the above statements. The pendulum-like behavior in this sounding seems to be stimulated by the buoyant oscillation of the atmosphere.