V,Al对Nb-Si系超高温结构材料抗氧化性能的影响

采用真空非自耗电弧炉制备了Nb-22Ti-12Si三元以及三种不同V,Al含量的Nb.Ti-Si-V-Al五元Nb-Si合金,研究了四种合金铸态显微组织和1250℃的抗氧化性能.结果表明:V,Al的加入促进了反应Nb3Si→Nb Nb Nb5Si3,使合金相组成由Nb Nb3Si转变成为Nb Nb5Si3,从而增加了合金中Nb相体积分数;合金的抗氧化性能随V,Al含量的增加而提高;V,Al的加入使合金氧化皮结构发生了转变,生成了较为致密的氧化皮,降低了合金的氧化速率,减少了合金氧化皮的剥落和金属氧化损失量.Nb-21.9 Ti-11.9Si-4.4V-4.1Al经过1250℃/50h氧化后金属损失厚度仅为0.1mm.     

激光熔化沉积Ti-6Al-2Zr-Mo-V钛合金组织特征研究

采用激光熔化沉积快速制造工艺直接成形Ti-6Al-2Zr—Mo—V合金板材。激光熔化沉积过程中合金粉末充分熔化并在液态均匀混合以得到成分均匀、全致密的组织。SEM分析表明,激光沉积Ti-6Al-2Zr-Mo—V合金具有均匀细小的α／β双相片层组织,且片层取向随机多样,分布均匀。其组织特点与激光沉积过程中的快速凝固和固态相变有关。解释了其特征组织的形成机理,并讨论了其沉积层组织特征对性能的影响。     

Al含量和冷速对TiAl合金全片层组织热稳定性的影响

研究Al含量和冷却速率对TiAl合金全片层组织在1150℃的热稳定性的影响.研究表明,Al含量在46at%～48at%范围的二元TiAl合金的Al含量越高,γ偏析程度越严重,铸造片层组织的热稳定性越差.Ti-48Al合金α单相区固溶处理后炉冷的粗片层组织的稳定性远远优于空冷的细片层组织,空冷细片层组织容易在晶界处发生不连续粗化转变,并且空冷片层晶粒内的魏氏片层(Lw)与基体的界面往往与晶界一同成为片层组织发生分解的起始部位.     

TA2钛合金表面Al2O3/石墨自润滑沉积层的制备及其摩擦学性能研究

采用阴极液相等离子体电解沉积技术(PED)在TA2钛合金表面一步制备了含石墨的Al2O3陶瓷沉积层。利用SEM和XRD对沉积层的结构和成分进行了表征,并探讨了沉积层的形成过程和机理。用摩擦试验机评价了沉积层的摩擦磨损性能。结果表明,通过在电解液中添加适量的石墨,利用PED技术可在TA2钛合金表面制备由α-Al2O3、γ-Al2O3和石墨相组成的复合沉积层。与TA2钛合金以及不含石墨的Al2O3沉积层相比,Al2O3/石墨复合沉积层的摩擦系数显著降低,磨损率随之减小,具有良好的减摩抗磨性能。     

新型多元铌合金的高温氧化行为

文摘研究了Nb-15Ti-11Al和Nb-15Ti-11Al-10Si两种多元铌合金在1 100和1 300℃高温下的氧化行为,建立了合金高温氧化动力学模型。结果表明:粉末冶金方法制备的铌合金微观组织细小,大大降低了氧的短路扩散;合金中的钛降低了氧在基体中的固溶度并降低了氧的扩散速率;合金中的硅在高温时形成熔融态的SiO2可有效地抑制Nb2O5的生长,从而保证了氧化膜表面均匀平整。     

Nb-38Ti-12Al 高温合金的氧化行为

利用已经制备的Nb-38Ti-12Al合金铸锭,将其加工为厚度为0.50 mm的板材,并通过X射线衍射分析(XRD)、金相显微镜(OM)、扫描电镜(SEM)、箱式电阻炉、分析天平等方法研究了合金在1 200℃下发生氧化反应后氧化膜出现的分层现象,通过计算单位面积内合金氧化增重质量,绘制出合金氧化增重曲线,并利用合金内氧化层厚度计算出在1 000℃和1 200℃的内氧化动力学方程,分别为x1.228=34.50t和x1.480=288.73t。     

DMLD在航空发动机修理中的应用

直接金属激光沉积(DMLD),又称激光净成形(LENS)、直接金属沉积(DMD)、直接激光沉积(DLD)、激光包覆以及粉末熔焊.其过程的实质是:用激光束在金属基体上形成一个熔池,将粉末送入熔池熔化并黏结在基体上形成沉积物.激光器以及粉末进给用的喷嘴均采用CNC机器手或龙门架式系统操作.     

Microstructure, Mechanical Properties and Oxidation Resistance of Nb-22Ti-14Si-2Hf-2Al-xCr Alloys

Nb-22Ti-14Si-2Hf-2Al-xCr (x=2, 6, 10, 14, 17 at%) alloys are prepared by arc-melting under argon atmosphere. Microstructural characteristics, mechanical properties and oxidation resistance of the arc-melted alloys are investigated. At 2 at% Cr content, the microstructure is composed of Nbss, Nb3Si and a small quantity of Nb5Si3, when the Cr contents increase, Nb3Si disappears. For the high Cr content (x ≥ 10 at%) alloys, besides the Nbss and Nb5Si3, Cr2Nb is also detected. With the increase of Cr content, the volume fractions of Cr2Nb and Nb5Si3 increase, while that of Nbss increases firstly and then begins to degrade when the Cr content is higher than 6 at%. For the alloy with 2 at% Cr, the room temperature fracture toughness is about 14.5 MPa·m1/2, but badly decreases to about 8.5 MPa·m1/2, when the Cr contents increase. Vickers hardness of Nbss tends to increase linearly from about 400 to 500, while that of silicides is not sensitive to Cr contents, about 950. The appearance of Cr2Nb phase significantly improves the high temperature oxidation resistance of the alloys with high Cr contents. The isothermal oxidation tests show that the oxidation kinetics of the alloys with various Cr contents follows parabolic oxidation kinetics.     

阴极微弧放电制备TiAl合金表面Al_2O_3膜的高温氧化性能

在Al(NO3)3溶液中利用阴极微弧放电沉积方法,制备了TiAl合金表面的Al2O3膜,膜的厚度为80μm。空气环境下,在900℃下进行高温氧化实验。利用扫描电镜(SEM)和X射线衍射(XRD)分析了样品在高温氧化前后的形貌和物相变化。100h高温氧化后,Al2O3膜保持完整,与基体有较好的结合。高温氧化前后物相均为γ-Al2O3和少量的α-Al2O3,但是氧化后的膜层中出现了少量的Rutile-TiO2。阴极微弧沉积方法在TiAl合金表面制备的Al2O3膜能够有效地提高基体在900℃时的抗氧化性能。     

AZ91D镁合金表面激光等离子复合喷涂Al-Si/Al+Al2O3涂层的研究

利用一种全新的激光等离子同时复合喷涂加工技术,成功在AZ91D镁合金表面制备了Al-Si/Al+Al2O3涂层,并研究了激光功率对涂层结构和性能的影响.利用SEM、光学显微镜法、XRD、显微硬度计等分析测试手段研究了在不同激光功率下的涂层形貌、孔隙率、相组成、显微硬度.结果表明:Al-Si过渡层明显改善了涂层与基体的结...     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

ν-gap度量及其在飞行控制律评估中的应用

 传统控制律评估方法主要用于单输入单输出（SISO）系统，且对模型参数摄动考虑不够全面,针对这些不足，研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上，给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算，提出ν-gap度量评估控制律的步骤。实例结果表明，该方法不仅克服了上述传统评估方法的缺陷，而且还有根据所求的各摄动影响情况忽略影响小的元素，以减少计算量及可以找到最坏情况下的参数摄动组合等优点。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Integrated Entry Guidance for Reusable Launch Vehicle

A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。