Z-源稀疏矩阵变换器励磁的双馈风力发电系统

针对矩阵变换器电压传输比低和其励磁的双馈风力发电系统(DFIG)易受非正常输入波动影响的不足,提出了一种适用于DFIG励磁的Z-源稀疏矩阵变换器系统。利用Z-源的升压特性来提高电压传输比,检测电容电压实现对直通因子的自动调节,从而实现对网侧波动的自动抑制。建立了系统数学模型,推导了DFIG系统定子磁场定向矢量控制策略表达式,搭建试验样机对所提方案进行试验验证,在亚同步、同步、超同步三种发电状态下的波形和并网试验结果验证了方案的可行和有效性。     

Space vector modulation strategy for an eight-switch three-phase NPC converter

A three-phase neutral point clamped (NPC) converter is presented for power factor correction and dc-link voltage regulation. A simplified space vector pulsewidth modulation scheme (SVPWM) is adopted to track line current commands. Using a simplified SVPWM algorithm, the calculated time for the time duration of voltage vector is reduced. The adopted NPC converter has less power switches compared with the conventional three-level NPC converter. Only eight power switches and four clamping diodes with voltage stress of half the dc bus voltage are used in the circuit configuration. Based on the proposed control algorithm, a reference voltage vector is generated on the ac terminal for drawing the sinusoidal line currents with unity power factor. Computer simulation and experimental results based on a laboratory prototype are presented to verify the validity and effectiveness of the proposed control strategy.     

Implementation of a single-phase AC/AC converter based on neutral-point-clamped topology

A single-phase ac/ac converter based on neutral-point-clamped scheme is proposed to perform unity input power factor and to provide a stable ac voltage to the critical loads. The ac/dc rectifier part is controlled to generate a unipolar pulsewidth modulation (PWM) waveform on the ac terminal by using four power switches with voltage stress of half the dc-link voltage. The carrier-based current control scheme is employed in the inner control loop to track the line current command. To regulate the dc bus voltage, a proportional-integral (PI) control is adopted in the outer control loop. The dc/ac inverter part of the system with four power switches is employed to generate a stable and clean sinusoidal output voltage to the critical load. The instantaneous current control scheme is used to track the output voltage command. To verify the effectiveness of the proposed control algorithm, the simulation and experimental results based on a laboratory prototype were implemented and discussed.     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

AC/DC converter topologies for the Space Station

A new class of AC/DC converter topologies (Type-1 converters) is described, suitable for use in an advanced single-phase sine-wave voltage, high-frequency power distribution system, of the type that was proposed for a 20 kHz Space Station primary electrical power distribution system. The converter comprises a transformer, a resonant network, a current controller, a diode rectifier, and an output filter. The input AC voltage source is converted into a sinusoidal current source using the resonant network. The output of this current source is rectified by the diode rectifier and is controlled by the current controller. The controlled rectified current is then filtered by the output filter to obtain a constant voltage across the load. Three distinct converter topologies, Type-1A, Type-1B, and Type 1-C, are described, and their performance characteristics are presented. All three types have a close-to-unity rated power factor (greater than 0.98), low total harmonic distortion in input current (less than 5%), and high conversion efficiency (greater than 96%)     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

Suitability of pulse train control technique for BIFRED converter

Pulse Train/spl trade/ control scheme is presented and applied to a boost integrated flyback rectifier/energy storage dc-dc (BIFRED) converter operating in discontinuous conduction mode (DCM), which avoids the light-load high-voltage stress problem. In contrast to the conventional control techniques, the principal idea of Pulse Train technique is to regulate the output voltage using a series of high and low energy pulses generated by the current of the inductor. The applicability of the proposed technique to both the input and magnetizing inductances of BIFRED converter is investigated. Analysis of BIFRED converter operating in DCM as well as the output voltage ripple estimation is given. Experimental results on a prototype converter are also presented.     

Bidirectional DC-to-AC inverter with improved performance

Switch-mode DC-to-AC inverters using DC-to-DC converter topology have many advantages over the traditional bridge-type inverter. A bidirectional power circuit combined with a nonlinear robust control is proposed to form a high performance inverter. The output voltage of the inverter can be stabilized regardless of large changes in input voltage and output current. The distortion near the zero crossing point can be minimized. The load of the inverter can be resistive, inductive, or capacitive. Simulation results and experimental verification are provided     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

Voltage-based maximum power point tracking control of PV system

Photovoltaic (PV) generators exhibit nonlinear v-i characteristics and maximum power (MP) points that vary with solar insulation. An intermediate converter can therefore increase efficiency by matching the PV system to the load and by operating the solar cell arrays (SCAs) at their maximum power point. An MP point tracking algorithm is developed using only SCA voltage information thus leading to current sensorless tracking control. The inadequacy of a boost converter for array voltage based MP point control is experimentally verified and an improved converter system is proposed. The proposed converter system results in low ripple content, which improves the array performance and hence a lower value of capacitance is sufficient on the solar array side. Simplified mathematical expressions for a PV source are derived. A signal flow graph is employed for modeling the converter system. Current sensorless peak power tracking effectiveness is demonstrated through simulation results. Experimental results are presented to validate the proposed method     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Feedforward maximum power point tracking of PV systems using fuzzy controller

A feedforward maximum power (MP) point tracking scheme is developed for the interleaved dual boost (IDB) converter fed photovoltaic (PV) system using fuzzy controller. The tracking algorithm changes the duty ratio of the converter such that the solar cell array (SCA) voltage equals the voltage corresponding to the MP point at that solar insolation. This is done by the feedforward loop, which generates an error signal by comparing the instantaneous array voltage and reference voltage. The reference voltage for the feedforward loop, corresponding to the MP point, is obtained by an off-line trained neural network. Experimental data is used for off-line training of the neural network, which employs back-propagation algorithm. The proposed fuzzy feedforward peak power tracking effectiveness is demonstrated through the simulation and experimental results, and compared with the conventional proportional plus integral (PI) controller based system. Finally, a comparative study of interleaved boost and conventional boost converter for the PV applications is given and their suitability is discussed.     

Analysis and design of a novel three-phase active power filter

A novel three-phase active power filter is analyzed and designed. A low cost power circuit configuration of the active power filter is proposed, along with a fast peak detector for synthetic sinusoidal generation technique, in order to achieve almost real time compensating current calculation. This technique avoids the use of mains voltage signal in the calculation of reference compensation current. Therefore, the mains current, after compensation, is still a pure sinusoidal waveform, irrespective of the distortion in the mains voltage. Furthermore, a critical value for the magnitude of capacitor voltage on the dc side, and a critical value for the reactor inductance on the ac side have also been derived, for the successful harmonic current tracking in various design applications. Finally, the performance of the active power filter is demonstrated by simulations as well as experimental results     

Novel single-phase AC/DC converter with two PWM control schemes

A novel single-phase AC/DC converter with two pulsewidth modulation (PWM) schemes is proposed to draw a sinusoidal line current with nearly unity power factor, achieve balanced neutral point voltage and regulate the DC bus voltage. With the aid of neutral point clamped scheme, a three-level voltage pattern is generated on the AC side of the proposed rectifier. To track the tine current command derived from a voltage controller and a phase-locked loop circuit, a hysteresis current control scheme is used in the inner loop control. A capacitor voltage compensator is employed to achieve the balanced neutral point voltage. To investigate the effectiveness of the proposed control scheme, the simulation and experimental results based on a laboratory prototype circuit are performed.     

Novel AC line conditioner for power factor correction

A new ac line conditioner is presented for high input power factor and clean ac output voltages for isolating the linear or nonlinear loads. A three-phase two-leg switching mode rectifier with neutral-point-clamped topology is proposed to draw the sinusoidal line currents from the ac mains. The carrier-based current controller is used in the inner control loop to track the line current commands with unity power factor. The dc bus voltage controller is adopted in the outer control loop to regulate the dc-link voltage. A voltage compensator is used to balance the neutral point voltage on the dc tank. A three-phase two-leg inverter with neutral-point-clamped topology is adopted in the system to provide the clean ac output voltages to the critical or sensitive loads. The carrier-based current control scheme is adopted to improve the instantaneous output voltages. Experimental results show the validity and effectiveness of the proposed control strategy.     

Full control of a PWM DC-AC converter for AC voltage regulation

The design and implement action of a DSP-based fully digital-controlled single-phase pulsewidth modulated (PWM) dc-ac converter for ac voltage regulation is described. The proposed multiloop digital controller (MDC) consists of a current controller, a voltage controller, and a feedforward controller. This MDC was realized using a single-chip digital signal processor (DSP). The PWM gating signals are determined at every sampling instant by the proposed multiloop digital control scheme using a set of detected feedback signals. A software current control; scheme has been developed to achieve fast current control of the PWM inverter and decouple the inductor of the output filter. Experimental results have been given to verify the proposed digital control scheme. The constructed DSP-based PWM dc-ac converter system can achieve fast dynamic response and with low total harmonic distortion (THD) for rectifier type of loads     

Single-phase power-factor-correction AC/DC converters with threePWM control schemes

Three pulse-width modulation (PWM) control schemes for a single-phase power-factor-correction (PFC) AC/DC converter are presented to improve the power quality. A diode bridge with two power switches is employed as a PFC circuit to achieve a high power factor and low line current harmonic distortion. The control schemes are based on look-up tables with hysteresis current controller (HCC) to generate two-level or three-level PWM on the DC side of diode rectifier. Based on the proposed three control schemes, the line current is driven to follow the sinusoidal current command which is in phase with the supply voltage, and two capacitor voltages on the DC bus are controlled to be balanced. The simulation and experimental results of a 1 kW converter with load as well as line voltage variation and shown to verify the proposed control schemes. It is shown that unity PFC is achieved using a simple control circuit and the measured line current harmonics satisfy the IEC 1000-3-2 requirements     

Analysis of a PWM-resonant converter

When a parallel resonant tank is excited by a bipolar current pulse train a sinusoidal voltage develops across the tank whose amplitude depends on the duty cycle of the pulse train. An isolated secondary can be derived by applying the tank voltage to an isolation transformer whose magnetizing inductance acts as the resonant inductor of the tank circuit. A dc output voltage is obtained after rectification and filtering of the sinusoidal secondary voltage and regulation is achieved by controlling the duty cycle of the pulse train. The sinusoidal nature of the voltage across the isolation transformer alleviates some of the noise problem associated with parasitic capacitances of an isolation transformer when operated with square voltage waveform. In this work the dc and small-signal analysis of the converter is given and an equivalent small-signal circuit model is derived. Experimental results which confirm the validity of the model are presented.     

Self-oscillating DC-to-DC switching converters with transformer characteristics

Fourth-order converters with both input and output filters are analyzed in self-oscillating sliding mode. The boost converter with output filter and the Cuk converter are shown to have stable dynamics and an equilibrium point with transformer characteristics. The analytical predictions are verified by experimental results.     

Robust controller design for a series resonant converter

Because of their reduced switching losses, allowing a higher operating frequency, dc-to-dc resonant converters have been used extensively in the design of smaller size and lighter weight power supplies. The steady state and dynamic behavior of both the conventional series and parallel resonant converters have been thoroughly analyzed and small-signal models around given nominal operating points have been obtained. These models have been used in the past to design controllers that attempted to keep the output voltage constant in the presence of input perturbations. However, these controllers did not take into account either load or components variations, and this could lead to instability in the face of component or load changes. Moreover, prediction of the frequency range for stability was done a posteriori, either experimentally or by a trial and error approach In this paper we use μ-synthesis to design a robust controller for a series resonant converter (SRC). In addition to robust stability the design objectives include rejection of disturbances at the converter input while keeping the control input and the settling time within values compatible with a practical implementation