共查询到20条相似文献,搜索用时 52 毫秒
1.
2.
3.
采用电化学阳极氧化技术在含NH4F的乙二醇电解液中对TiAl合金进行阳极氧化处理。研究阳极氧化对TiAl合金高温氧化行为和力学性能的影响。结果表明:由于“卤素效应”,阳极氧化处理的TiAl合金经高温氧化后表面形成致密、连续的Al2O3氧化膜,有效阻止了氧的内扩散,进而显著提高合金的抗高温氧化性能。经1000℃氧化100 h后,阳极氧化试样增重由未经阳极氧化处理试样的85.86 mg/cm2降至0.67 mg/cm2。另一方面,阳极氧化TiAl合金表面硬度和弹性模量随高温氧化时间延长呈先降低后升高的趋势。阳极氧化TiAl合金在高温服役后,合金的摩擦系数较未经阳极氧化处理试样上升,但表面耐磨性先降低后升高。这是由于TiAl合金经阳极氧化后,表面形成了一层富铝含氟氧化膜,由于氧化膜中F元素在高温氧化过程中与Ti、Al结合形成卤化物,卤化物蒸气选择性扩散在原始氧化膜处形成致密的Al2O3保护膜。阳极氧化对TiAl合金力学性能的影响主要是由于氧化膜中Al2O3的含量变化所致。 相似文献
4.
TiAl合金以其优异的性能被广泛应用于航空、航天制造领域,但由于TiAl合金自身的物理、化学特性,导致其切削性能较差,加工过程中容易出现工件表面烧伤、表面微裂纹等问题。为了研究TiAl合金铣削加工过程中切削工艺参数对加工表面裂纹的影响规律,设计了TiAl合金切削参数与加工表面裂纹之间的正交试验。结果表明:切削速度对TiAl合金铣削表面裂纹的影响最大,其次是切削深度和切削宽度,每齿进给量对表面裂纹的影响最小。基于遗传算法,以表面裂纹长度为目标函数,优化得到的最优参数组合为:ae=0. 2 mm、ap=0. 2003 mm/z、fz=0. 02001 mm/z、vc=20. 0004 m/min。采用优化后的参数铣削TiAl合金,发现工件表面的实际加工裂纹长度和经过算法优化的裂纹长度相差较小,该优化方法可行性较高,误差较小。 相似文献
5.
6.
全片层TiAl合金的片层取向和片层间距控制的研究现状 总被引:1,自引:0,他引:1
《航空材料学报》2015,(5)
全片层TiAl合金的片层取向和片层间距对其断裂韧性、屈服强度、蠕变性能和疲劳性能等力学性能具有重要影响。本文从片层取向控制和片层间距控制两方面,系统的综述了全片层TiAl合金的性能和组织间的关系,并总结了提升全片层TiAl合金的性能的手段。指出取向与晶体生长方向相同、片层间距细小的全片层TiAl合金具有最优的综合力学性能;减小Al当量、增大生长速度和环境压力可减小全片层TiAl合金的片层间距,增大Al当量是最简单有效的细化片层的手段;自引晶法是控制片层取向的新兴方法,是未来TiAl合金片层取向控制的重要发展方向。 相似文献
7.
8.
TiAl合金作为准脆性材料,在其服役过程中由于缺口的存在使得断裂对缺口非常敏感,严重降低了其使用性能,因此需要研究TiAl合金在缺口作用下的断裂性能。采用带缺口的组合拉伸试样研究了温度和拉伸速率对具有近全片层组织Ti-48Al-2Cr-2Nb合金缺口断裂性能的影响。结果表明,室温下TiAl合金对缺口非常敏感,随着温度的升高,TiAl合金对缺口敏感性降低,当温度为800 ℃时,TiAl合金对缺口不敏感。TiAl合金在低温区塑性变形是通过位错滑移和变形孪晶引起的,高温下是由扩散控制的位错攀移作用引起的。研究还表明,200 ℃下拉伸速率较低时TiAl合金对缺口不敏感,当拉伸速率增加到较高时,TiAl合金对缺口很敏感。 相似文献
9.
齐立春%黄旭%李臻熙 《宇航材料工艺》2006,36(Z1):12-17
综述了改善TiAl合金高温抗氧化性能的近期研究进展,着重介绍了合金元素对TiAl合金高温抗氧化性能的影响、表面改性及抗氧化涂层对改善其高温抗氧化性能的作用等.综合来看,通过合金化并结合先进的表面防护方法是改善TiAl合金800℃以上高温抗氧化性能的非常有效的途径. 相似文献
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:2,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
14.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
15.
16.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
17.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
18.
Integrated Entry Guidance for Reusable Launch Vehicle 总被引:2,自引:2,他引:0
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
19.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
20.
(高)超声速流动试验技术及研究进展 总被引:1,自引:1,他引:1
近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。 相似文献