Cf / ZrB2 -SiC 复合材料的制备及抗热冲击性能

采用前驱体转化法制备Cf / ZrB2 -SiC 复合材料,对材料的热物理和热震性能进行了研究。采用 扫描电镜和X 射线衍射分析材料的微观结构及物相变化。结果表明:复合材料在1 700℃热震循环10 次材料 保持完整,表现出了良好的抗热震性能。通过微观结构分析,高温氧化后生成的多孔SiO2 氧化层能够吸收热 应力,缓解因热震带来的巨大温度差,ZrB2 组元的加入有效地提高了材料抗热震性。     

短碳纤维增韧石英复合材料性能研究

以短碳纤维为初始原料，采用溶胶一凝胶技术引入SiO2组分，在一定的热压烧结制度下得到致密Cf／SiO2复合材料；研究了其烧结条件、力学性能、线膨胀及烧蚀性能。实验表明，基体保持非晶态，可达到99％的致密度；随碳纤维含量的增加，弯曲强度(σf)无显著变化，断裂韧性(KIC)先升后降；线膨胀系数随碳纤维含量增加而增加，该材料具有良好的抗热震及耐烧蚀性能。     

溶胶-凝胶法制备纳米SiO2／CE复合材料的研究

采用溶胶-凝胶法,利用正硅酸乙酯(TEOS)在有机溶剂中的水解-缩合制备纳米SiO2.将所制备的纳米SiO2用于改性双酚A型氰酸酯树脂(BADCy),制备纳米SiO2/BADCy浇铸体.采用透射电镜(TEM)分析SiO2在BADCy基体中的分散性,同时测试了复合材料的力学性能.结果表明,粒径为20～50 nm的SiO2在基体中以纳米量级均匀分散,与BADCy结合界面模糊,两者具有较好粘结性;添加纳米SiO2可以明显提高复合材料的冲击强度和弯曲强度,当纳米SiO2的含量为4%时,力学性能改性效果最佳.     

碳纤维含量对Cf/SiO2复合材料组织与性能的影响

采用真空热压烧结工艺制备了碳纤维体积分数分别为20％、40％和60％的高致密Cf/SiO2复合材料，研究了碳纤维含量对其组织结构，力学性能、热膨胀特性和抗氧化性能的影响规律。结果表明：SiO2基体及20％Cf/SiO2复合材料中，SiO2仍保持非晶态，碳纤维含量为40％和60％时，SiO2发生部分析晶；Cf/SiO2复合材料的抗弯强度、断裂韧性和断裂应变，随碳纤维含量增加均呈现先降低后又增加的趋势，而弹性模量则先增后降；60％Cf/SiO2表现出明显伪塑性；碳纤维含量增大，使复合材料的热膨胀系数成倍增加，抗氧化性变差。     

高温处理对中密度针刺C/C复合材料性能的影响

针对C/C复合材料脆性问题,对密度为1.60 g/cm3的碳布叠层针刺C/C复合材料进行了1800、2 000、2 200和2 500℃的高温处理,研究了不同热处理温度对C/C复合材料微晶结构、力学和抗热震等性能的影响.结果表明,高温处理使针刺C/C复合材料的层间剪切和面内拉伸强度出现不同程度的降低,但材料的断裂伸长率和抗热震性能得到大幅度提高.其中,1 800℃高温处理后的C/C复合材料具有优异的力学和抗热震性能.     

SiO2—Si3N4天线窗材料的热学性能和抗热震性能研究

研究了ＳｉＯ２－Ｓｉ３Ｎ４天线窗材料的热学性能和抗热震性能。结果表明，复合材料的热膨胀系数、导温系数、导热系数随Ｓｉ３Ｎ４含量的增加而增大，对于同一Ｓｉ３Ｎ４含量的复合材料，三者均随温度的升高而增大，复合材料保持了ＳｉＯ２基体材料的良好抗热震性。     

MOCVI法制备SiO2/SiO2复合材料

依据金属基化学气相渗透法(Metal Organic Chemical Vapor Infiltration,MOCVI)工艺理论基础,采用MOCVI法制备出SiO2/SiO2复合材料,并分析了载气流量、先驱体JH20温度和沉积温度对氧化硅基体渗透速率和SiO2/SiO2(石英玻璃)复合材料显微结构的影响.结果表明,优化条件为:JH20的温度为60℃,载气流量为500mL/min,氧气流量为15mL/min,沉积温度为600℃.     

TiC—TiB2／Cu复合材料的抗热震及抗烧蚀行为研究

采用SHS/PHIP工艺制备了TiC-TiB2/xCu复合材料,分析了材料的组成及显微结构,利用等离子火炬加热器考察了材料的抗热震及抗烧蚀性能.结果表明,随着金属Cu含量的增加,TiC-TiB2/xCu复合材料的抗热震性增强,而抗烧蚀性能降低;在经过15s烧蚀后,材料的质量损失为1.7g,质量烧蚀率为0.11g/s.材料的抗烧蚀机理为耐高温、耐冲刷的高强度陶瓷骨架以及高温下挥发吸热的金属Cu粘接剂,二者的综合作用使材料具有抗烧蚀性.     

碳纤维含量对Cf/SiO2复合材料组织与性能的影响

采用真空热压烧结工艺制备了碳纤维体积分数分别为20%、40%和60%的高致密Cf/SiO2复合材料,研究了碳纤维含量对其组织结构、力学性能、热膨胀特性和抗氧化性能的影响规律.结果表明SiO2基体及20%Cf/SiO2复合材料中,Si2仍保持非晶态,碳纤维含量为40%和60%时,Si2发生部分析晶;Cf/SiO2复合材料的抗弯强度、断裂韧性和断裂应变,随碳纤维含量增加均呈现先降低后又增加的趋势,而弹性模量则先增后降;60%Cf/Si2表现出明显伪塑性;碳纤维含量增大,使复合材料的热膨胀系数成倍增加,抗氧化性变差.     

Mo-Si涂层C/SiC复合材料的氧化性能

采用刷涂法在C/SiC复合材料表面制备Mo-Si抗氧化涂层,研究涂层的微观结构、氧化性能和热震性能.结果表明,涂层中存在微裂纹等缺陷,物相组成为MoSi2、SiO2、SiC和Si.1 400℃氧化时,微裂纹等缺陷迅速愈合.单层Mo-Si涂层试样经5 h氧化后,失重率高速5.90%,贯穿裂纹是涂层失效的主要原因.三层Mo-Si涂层试样经140h氧化后,失重率仅为1.37%,失重速率为3.80×10-5g/(cm2·h).在1 400℃(←→)100℃的热震过程中,涂层保持完整,热震50次的失重率为0.34%.经25次和50次热震后,涂层试样的弯曲强度保持率分别为90.30%和74.56%.三层涂层具有优异的抗氧化和抗热震性能,这与涂层的制备工艺和结构密切相关.     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.