Alternate forms of the PWM switch models

Vorperian's pulsewidth modulation (PWM) switch model consists of a PWM transformer and a nonlinear resistor. The recognition that any of the three transformer terminals can serve as the common terminal leads to two alternate PWM transformer models and the corresponding two alternate PWM switch models. For a given PWM dc-dc converter, one of the three PWM switch models is more “natural” for graphic-oriented analysis/design, e.g., it allows the idealized converter to be analyzed by inspection. Furthermore, all three PWM transformers may be used to graphically manipulate the converter circuit to a form that can be analyzed by inspection. The alternate forms of the PWM transformers and the PWM switch models are effective as graphic-oriented teaching and learning tools for PWM converters. This is demonstrated using examples based on the boost converter and the Cuk converter     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

Simplified analysis of PWM converters using model of PWM switch.II. Discontinuous conduction mode

For pt.I see ibid., vol.26, no.3, p.490-6 (1990). According to the method of state-space averaging, when a pulsewidth modulation (PWM) converter enters discontinuous conduction mode (DCM), the inductor current state is lost from the average model of the converter. It is shown that there is neither theoretical nor experimental justification for the disappearance of the inductor state as claimed by the method of state-space averaging. For example, when the model of the PWM switch in DCM is substituted in the buck, boost, or buck-boost converter while the inductor is left intact, the average model has two poles: the first pole f_p1 agrees with the single pole of state-space averaging, while the second pole f_p2 occurs in the range f_p2⩾F_s/π. It is shown that the right-half plane zeros present in the control-to-output transfer functions of the boost, buck-boost, and Cuk converters in continuous conduction mode are also present in discontinuous conduction mode     

单相PWM整流电路控制方法及仿真分析

分析单相PWM整流电路的结构、工作原理和控制方法,通过选择适当的工作模式和工作时序,可使PWM整流电路输出直流电压稳定。将正弦脉宽调制技术应用于PWM整流电路,使其交流侧输入电流非常接近正弦波,且与输入电压同相位。同时调节交流侧电流的大小和相位,使能量在交流侧和直流侧双向流动。在建立基于Simu-link7.6的仿真模型基础上,通过分析PWM整流电路各处电压、电流波形,验证其控制方法及仿真设计的正确性。     

Generation and classification of PWM DC-to-DC converters

A method is presented by which generation and classification of pulsewidth-modulated (PWM) DC-to-DC converters can be effected. Fundamental blocks known as converter cells can be used to generate a plethora of converters leading to a number of useful new converter topologies. A classification of basic converters is proposed in terms of converter-cell generated families     

飞机调压系统传递函数的建立及动态分析

本文说明如何建立飞机ＰＷＭ晶体管调压器的传递函数，包括：检比电路；调制、整形放大电路；功率放大电路及校正网络的传递函数。阐明了用实验法求取交流发电机的传递函数，及对飞机调压系统动态分析的基本方法。     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Steady-state analysis of PWM DC-to-DC regulators

A new method for steady-state analysis of pulsewidth modulation (PWM) hard-switching DC-to-DC regulators is presented. The power stage and the feedback control circuit are analyzed as two interconnected blocks. The intersection of their open-loop DC steady-state characteristics with the ramp voltage provides a guess candidate steady-state solution (CS). An iterative process is used to validate it as true steady-state solution (TS) when the bias conditions of switching devices (SDs) are fulfilled everywhere in the switching period.     

Random hysteresis PWM inverter with robust spectrum shaping

A hysteresis current-controlled pulsewidth modulation (PWM) scheme is simple and robust in switching control, but it is subject to not constant switching frequency. However, since its harmonic spectrum is not randomly distributed like those yielded by the random PWM (RPWM) scheme, the annoying harmonic effects still exist. A random switching control strategy is proposed here to let the harmonic spectrum of the hysteresis current-controlled PWM inverter be randomly distributed. First, the effect of varying band on the harmonic distribution characteristic of a hysteresis current-controlled PWM scheme is analyzed. Then a random hysteresis PWM scheme and its quantitative design procedure are proposed. Finally, a robust spectrum shaping technique is devised such that the desired harmonic distribution pattern can be achieved. In the resulting frequency spectrum, the magnitudes of lower frequency harmonics are shaped and reduced. Hence the inverter output with a better harmonic attribute is obtained. Validity of the proposed random hysteresis PWM scheme is verified by some simulated and measured results     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

并联H桥DC/DC变换器软开关技术研究

与传统的Buck电路相比,基于H桥并联的DC/DC变换器可以实现电压的双极性输出和故障时的冗余控制,非常适合用于大功率电动机正反转控制的场合。分析了并联H桥型DC/DC变换器的结构组成和双脉宽调制(PWM)模式。为了降低双脉宽调制下H桥型DC/DC变换器的开通和关断损耗,对无源软开关技术进行了分析,重点探讨了RCD缓冲电路和最小应力缓冲电路之间的性能差异,指出最小应力软开关技术可以获得更好的软开关性能,并就将其用于双脉宽调制下的并联H桥DC/DC变换器进行了仿真研究。仿真结果表明:最小应力软开关技术用于双脉宽调制下并联H桥DC/DC变换器时,可以实现开关管的零电压开通和零电流关断。     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

Interleaved buck converters with a single-capacitor turn-off snubber

This paper proposes interleaved buck converters with a single-capacitor snubber to smooth out switch turn-off transition. The single-capacitor snubber is used to limit rising rate of drain-source voltage of the metal-oxide-semiconductor field-effect transistor (MOSFET) switch in the converters to reduce turn-off loss. In addition, the converters are operated at the boundary of continuous and discontinuous conduction modes (CCM), (DCM) to reduce turn-on loss, and in an interleaving fashion to reduce output current ripple. As compared with the counterparts of conventional converter topologies, the proposed converters have the merits of less component count, higher efficiency over a certain load range, smaller size, and they are easier to implement. Hardware measurements obtained from experimental prototypes have verified these merits.     

CIECA: Application to Current Programmed Switching Dc-Dc Converters

Sundstrand Advanced Technology Corporation The current injection equivalent circuit approach (CIECA) to modeling switching converter power stages is extended to model the current programmed converter power stages operating in fixed frequency, continuous inductor conduction mode. To demonstrate the method, modeling is carried out for the buck, boost, and buckboost converters to obtain small-signal linear equivalent circuit models which represent both input and output properties. The results of these analyses are presented in the form of linear equivalent circuit models as well as transfer functions. Though current programmed converters exhibit single-pole response, the addition of artificial ramp changes converters to exhibit well damped two-pole response. This has been investigated for the first time using CIECA. The results of these analyses are presented in the form of linear equivalent circuit models as well as transfer functions.     

Novel single-phase AC/DC converter with two PWM control schemes

A novel single-phase AC/DC converter with two pulsewidth modulation (PWM) schemes is proposed to draw a sinusoidal line current with nearly unity power factor, achieve balanced neutral point voltage and regulate the DC bus voltage. With the aid of neutral point clamped scheme, a three-level voltage pattern is generated on the AC side of the proposed rectifier. To track the tine current command derived from a voltage controller and a phase-locked loop circuit, a hysteresis current control scheme is used in the inner loop control. A capacitor voltage compensator is employed to achieve the balanced neutral point voltage. To investigate the effectiveness of the proposed control scheme, the simulation and experimental results based on a laboratory prototype circuit are performed.     

一种新型结构机电混合式功率控制器技术研究

 分析了飞机270 V高压直流电力系统中对高压开关的需求,介绍了一般的混合式功率控制器（EMPC）的结构并分析了它所存在的缺陷。提出了一种新的EMPC结构形式,该结构基于RCD+继电器的吸收网络,有效地吸收关断电压尖峰,又不会在开通瞬间造成短路,新的控制方案还解决了EMPC的开通带容性负载的问题。实验表明,新型的EMPC既具有无触点开关不产生电弧的性能,又具有机械接触器导通压降小的优点,对负载的适应能力强,适合于在飞机270 V高压直流电力系统中使用。     

Resonant power supplies: their history and status

The various types of converter are described, and the history of resonant power supplies is briefly sketched. The differences between pulse-width-modulated (PWM) switch mode power supplies and resonant power supplies are discussed. Single-switch, multiple-switch, and series and parallel resonant converters are examined. The control of resonant converters is addressed. Hardware is briefly considered     

Improved ZCS-PWM commutation cell for IGBTs application

An improved zero-current-switching pulsewidth-modulated (ZCS-PWM) commutation cell is presented, which is suitable for high-power applications using insulated gate bipolar transistors (IGBTs) as the power switches. It provides ZCS operation for active switches and zero-voltage-switching (ZVS) operation for passive switches. Besides operating at constant frequency and reducing commutation losses, the proposed ZCS-PWM switch cell has no additional current stress and conduction loss in the main switch. To demonstrate the feasibility of the proposed ZCS-PWM commutation cell, it was applied to a boost converter. Operating principle, theoretical analysis, design guidelines, and a design example are described and verified by experiment results obtained from a prototype rated 1 kW and operating at 40 kHz. The PWM switch model and state-space averaging approach is also used to estimate and examine the steady-state and dynamic character of ZCS-PWM boost converter system. Finally, the application of the proposed soft-switching technique in the dc-dc nonisolated converters is presented.     

PWM静电伺服技术在电容微加速度计中的应用

根据实际条件,选用了PWM脉宽调制技术作为电容式加速度计静电平衡回路的实现方法。该方法与其他方法相比,更易于实现,而且整体组成也较为简单。     

九开关变换器驱动六相电机的载波调制PWM控制

针对九开关变换器驱动六相永磁同步电机系统的断相运行状态,研究了一种基于有效作用时间的载波调制PWM控制方法。给出了九开关变换器及基于有效作用时间的载波调制PWM控制的基本原理,建立了正常情况下六相PMSM的数学模型,根据单相和两相断路后电机相应的约束条件,采用空间解耦变换矩阵,分别建立了单相断路和两相断路后的电机数学模型,在Matlab/Simulink中进行了仿真实验,验证了所提控制方法的可行性。