Strength Prediction of Cruciform Specimen Under Biaxial Loading

In order to achieve a better understanding of failure behavior of cruciform specimen under different biaxial loading conditions,a three-dimensional finite element model is established with solid and interface elements.Maximum stress criterion,two Hashin-type criteria and the new proposed criteria are used to predict the strength of plain woven textile composites when biaxial loading ratio equals 1.Compared with experimental data,only the new proposed criteria can reach reasonable results.The applicability of the new proposed criteria is also verified by predicting the tensile and compressive strength of cruciform specimen under different biaxial loading ratios.Moreover,the introduction of interface element makes it more intuitive to recognize delamination failure.The shape of the predicted delamination failure region in the interface layer is similar to that of the failure region in neighboring entity layers,but the area of delamination failure region is a little larger.     

Modeling and Characteristic Analysis of Visco-Hyperelastic Film Based on Biaxial Tensile Experiment

Dielectric elastomers(DEs) show complex mechanical behaviors with different boundary conditions,geometry sizes,and prestress. In this study,a three-component linear visco-hyperelastic model of DE film is developed based on equibiaxial tension. By applying hereditary integrals to analyze multiple-segment loading processesof film stretching,the model parameters are extracted by fitting the visco-hyperelastic film model to the experimental data. To demonstrate the performance of proposed model,the obtained predictive results are compared with the experimental results under different equibiaxial loading conditions. The good agreement between them shows that the linear visco-hyperelastic model is a promising tool for analytically investigating the property of pre-stretched DE actuators. Finally,the Prony series coefficients are calculated according to the relaxation function. This is helpful for simulation analysis using commercial finite element software.     

高强高模聚乙烯纤维对大掺量矿物掺合料高强混凝土抗冻性的影响

用快冻法研究高性能的高强高模聚乙烯(High elasticity module polyethylene,HEMP)纤维对大掺量矿物掺合料高强混凝土(High strength concrete,HSC)抗冻性的影响.结果表明,大掺量矿物掺合料HSC具有较好的抗冻性,但是其抗冻性对养护环境RH非常敏感,干燥养护条件下的冻融寿命仅有标准养护的38%～40%.掺加0.1%HEMP纤维虽然降低了大掺量矿物掺合料HSC的抗冻性,但能够显著改善其抗冻性对养护环境RH的敏感性,在30%RH～50%RH养护条件下的冻融寿命高达标准养护时的81%～90%.     

Q460高强度钢内螺纹挤压力的模型

根据飞机起落架冷挤压内螺纹的成形过程,建立了冷挤压内螺纹接触应力与挤压力的力学模型,通过合理假设及取定挤压过程中的各工艺参数,计算出了挤压变形区工件沿挤压丝锥棱齿法向的接触应力及挤压力,并对切向挤压力实际测量数据与模型计算数据进行对比.结果表明,切向挤压力的理论计算与实测变化趋势基本相同,切向挤压力在整个冷挤压过程中的平均值相当,实测切向挤压力峰值接近于理论计算挤压力的峰值,验证了该内螺纹冷挤压力学模型的有效性.而一般切向挤压力计算值要比试验值略小些,主要由挤压丝锥锥部前端金属堆积与摩擦条件的变化引起.     

基于MOC8试验要求的飞行模拟器鉴定研究

阐述了采用飞行模拟器开展MOC8试验的原因和背景,在总结某型号飞机模拟器试验的基础上,对采用飞行模拟器开展MOC8试验进行了探讨。     

基于DSP和FPGA的模拟机数字多通道电路测试系统研制

采用DSP和FPGA相结合的方式,研制出一套数字电路测试系统,以FPGA仿真运行环境、DSP作为系统控制,可对模拟机多通道数字信号板进行测试,实现故障通道的检测。该系统电路结构简单,实用,具有可扩展性。     

基于QST-600通用气瓶试验台的水压试验方法研究

介绍QST-600通用气瓶试验台的优点、结构、技术指标以及水压试验操作的具体步骤和注意事项,为气瓶的水压试验提供一定的技术保障。