直升机旋翼粘弹阻尼器研制与应用

本文介绍了我所研制直升机旋翼粘弹阻尼器的简要过程,并结合研制中的“板式”和“扭转”型粘弹阻尼器的设计,简要概述了这两种典型结构参数的确定过程及其试验结果。经过两种型号四种粘弹阻尼器的研制证明其工程设计方法可行有效,作为一种工程设计方法的应用具有较大的实用价值,对相关专业工程设计也有其借鉴作用。     

新型液弹阻尼器原理与初步构型设计分析

液弹阻尼器是一种全新的直升机旋翼摆振阻尼器构型。本文介绍了这种直升机旋翼摆振阻尼器的工作原理，并通过对液弹阻尼器的弹性刚度和阻尼刚度的计算公式进行推导，得出了一套可供使用的液弹阻尼器的初步构型设计计算公式。     

旋翼改进研制中的动力学匹配分析

本文概要地介绍了直8旋翼改进研制的特点和动力学匹配分析的工作思路。对立足国内技术进行研制的过程中,从桨毂构型选择、阻尼器布置方式选择、复合材料桨叶结构特性相似性设计、旋翼动力学优化设计和地慢转速设置等方面综合考虑旋翼与全机动力学匹配问题,并略述了对这些问题的分析、处理情况及结果。     

液压阻尼器对模型旋翼地面共振的影响

 分析了某采用定压阀和补油装置的液压阻尼器的非线性特性。对无铰式模型旋翼的地面共振稳定性进行了数值仿真研究,分析了两种不同的非线性液压阻尼器对地面共振稳定性的影响。结果表明：由于补油分配阀间隙的影响,阻尼器低速时的有效阻尼大大下降;在无阻尼器的模型旋翼稳定的转速区内,该阻尼器不能改善系统小扰动情况时的动稳定性;在无阻尼器的模型旋翼不稳定区内,系统将出现极限环,且极限环幅值随补油分配阀间隙的增大而增大。研究结果对液压阻尼器的设计具有参考价值。     

嵌入式液弹阻尼器原理分析与试验研究

在过去的几十年里,直升机旋翼系统的设计都着重强调旋翼桨毂的简单化,总体趋势是减少零部件个数,减少重量,减小阻力和降低维护成本,传统的液压阻尼器和粘弹阻尼器正在被液弹阻尼器取代。随着技术和工艺上的革新,制造出带嵌入式液弹阻尼器的无轴承旋翼系统已切实可行。对嵌入式液弹阻尼器的动态力学性能进行了理论研究,介绍了其工作原理,并推导出初步构型设计计算公式,系统地对嵌入式液弹阻尼器模型试验件进行了动力学试验,研究了工作性能的各种影响因素,形成了一套完整的工程设计方法,为今后嵌入式液弹阻尼器在无轴承式直升机上的应用提供了技术支持。     

垂直着陆中直升机旋翼动力学行为研究

提出了直升机垂直着陆撞击激起旋翼扰动的动力学模型,为预估粗暴着陆时起落架载荷和旋翼液压阻尼器轴向速度幅值给出了一种数值模拟方法。以弹性轴承旋翼直升机为例,对垂直着陆时直升机机体、起落架、旋翼桨叶及阻尼器的动力响应进行了数值模拟,分析了着陆撞击引起机体和旋翼扰动的力学机理,可知在起落架触地后的第1个振荡周期中,各片桨叶将经历其不同的摆振幅值,并激起旋翼摆振后退型响应。着陆撞击引起桨叶的大扰动,将冲开阻尼器的定压安全活门,严重降低其等效阻尼。随机着陆时,起落架触地速度及过载系数、旋翼挥舞及摆振幅度和阻尼器速度峰值等动态参数由于着陆时机体的姿态角及角速度不同呈现很大的分散性,其分散性与着陆高度有关。     

直升机旋翼黏弹阻尼器时域动力学建模与分析

建立一种适用于旋翼气动弹性分析的黏弹阻尼器模型,该模型考虑了黏弹材料本身的刚度非线性及激振力频率和幅值对黏弹阻尼器应力-应变关系的影响。通过引入新型几何非线性弹簧模块,根据需要调整模型的刚度变化规律,避免了现有黏弹阻尼器模型模拟不同类型材料时因刚度变化规律差异而需重新建模的缺陷,模型适应性强。模型采用多个内变量场,既能体现阻尼器幅变特性,也能准确反映多频激励下的黏弹性特性。以两种不同类型黏弹材料制造的黏弹阻尼器为研究对象,在旋翼黏弹阻尼器的典型工作幅值和频率范围内,进行了简谐实验。利用建立的旋翼黏弹阻尼器非线性时域动力学模型,计算不同类型黏弹材料制造的阻尼器在多种应变幅值、频率下的动态特性并与实验相比较,分析了黏弹阻尼器损耗模量、储能模量频变特性和双频激励对阻尼器的影响。结果表明,建立的非线性黏弹阻尼器动力学模型能够更好地反映不同类型黏弹材料构成的黏弹阻尼器的动刚度和阻尼,适合于直升机旋翼载荷计算和气动弹性分析。     

直升机旋翼多层层压黏弹阻尼器多参数动力学建模与分析

针对基于柔性多体系统动力学的直升机旋翼系统动力学建模方法的要求,结合嵌入式多层层压黏弹阻尼器结构特点,建立了基于内变量理论的嵌入式多层层压黏弹阻尼器时域模型.通过引入多层内变量场,改善模型在较宽应变幅值范围和激振频率范围内计算阻尼器动特性及双频激振下动特性的能力.在阻尼器建模过程中考虑了嵌入式多层层压黏弹阻尼器中金属隔片的影响,引入温度传递函数考虑了阻尼器在工作过程中温度上升对黏弹材料的影响,提高了阻尼器模型的精度.通过计算分析与实验结果相比较,验证了阻尼器模型在不同应变幅值、激振频率以及双频激振下的有效性,为直升机旋翼气弹分析计算提供了一种嵌入式多层层压黏弹阻尼器模型.      

基于叶间布置的球柔性缩比模型桨毂阻尼器设计与分析

主要介绍了叶间布置的球柔性缩比模型桨毂阻尼器的设计与分析,解决了由于缩比模型桨毂尺寸小,阻尼器难布置,以及与4米模型旋翼试验台“地面共振”的问题,设计出合适的阻尼器尺寸和满足要求的性能参数。     

阻尼器叶间布置的旋翼动态摆振角分析

阻尼器的主要作用是提供摆振方向的约束刚度和约束阻尼,然而,叶间布置的阻尼器在集合型整体振动不提供摆振刚度和阻尼,这样,桨毂支臂的摆振角度会大一些。为了避免桨毂支臀碰撞桨毂中央件,需要对旋翼桨叶摆振角度进行详细的计算,并进行合理的设计。但是,旋翼摆振角受直升机飞行状态、过载系数、重心位置等因素的影响,属于多约束条件的动态非线性问题,本文介绍了一种通过数值仿真计算直升机旋翼摆振角的工程设计方法和思路。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.