SiC纤维CVD涂层工艺研究

对SiC纤维的CVD涂层工艺进行研究.实验发现采用BCl3,H2及CH4作为反应气体,采用与SiC纤维生产工艺相匹配的走丝速度并控制一定的工艺参数,在1350℃左右可得到厚度2～3mm且表面致密的B4C涂层,纤维涂层后性能基本保持不变.仅采用BCl3及CH4作为CVD涂层工艺反应气体,在1180～1250℃即可沉积出表面光滑致密,厚度2～3mm的富碳B4C涂层,涂层后纤维性能可提高10%左右,且涂层与纤维结合强度很高,优于B4C涂层与SiC纤维的结合强度.实验还发现SiC纤维涂覆B4C及富碳B4C涂层后,能有效阻隔界面反应,可大幅提高SiC/Ti基复合材料的性能.     

La3＋掺杂 Ni0．35 Co0．15 Zn0．5 Fe2 O4铁氧体的制备及微波吸收性能

采用溶胶-凝胶自蔓延法制备 La3＋掺杂 Ni0．35 Co0．15 Zn0．5 Fe2 O4,并研究不同掺杂量对样品微观结构、电磁参数及微波吸收性能的影响。通过 X 射线衍射仪、扫描电镜研究了样品的相结构和微观形貌,使用振动样品磁强计与矢量网络分析仪分别对样品的静态磁性能及在1～12GHz 的电磁参数进行了研究,并计算了不同厚度（3 mm、5 mm、8 mm）下材料的反射损耗。研究表明,适量掺杂 La3＋能够提高 Ni0．35 Co0．15 Zn0．5 Fe2 O4铁氧体的吸波性能,并使吸收频带向高频移动。其中样品 Ni0．35 Co0．15 Zn0．5 La0．04 Fe2 O4与石蜡混合厚度为5mm 时,最小反射损耗为－28．4dB,小于－10dB 带宽为3．7GHz。     

烧蚀条件下氮化硼材料表面的产物分析

建立了氮化硼材料基于热化学平衡条件下的烧蚀模型,并进行了数值模拟分析.结果表明:在烧蚀的过程中氮化硼材料表面形成的主要产物为BO、B2O、B2O2及B2O3;当压力升高时,有利于B2O2及B2O3的产生,不利于BO,B2O的产生,而无因次的质量损失率呈降低的趋势.     

盐雾环境中高强铝合金点腐蚀行为与暴露面积的关系

针对中性盐雾环境中2A12和7B04铝合金在不同暴露面积(模拟铝合金表面涂层或者膜层破坏暴露的部分)的点腐蚀特征开展研究,测量观察不同情况下铝合金的点腐蚀坑开口面积、腐蚀深度和点腐蚀坑数量等腐蚀参数。研究表明,在中性盐雾环境中,当暴露面积小于25mm2时,2A12和7B04铝合金的点腐蚀坑最大开口面积随暴露面积的增大而增大;当暴露面积小于4mm2时,2A12铝合金的最大腐蚀深度随着暴露面积的增大而增大,而7B04铝合金的最大腐蚀深度在暴露面积小于100mm2时随着暴露面积的增大而增大。对腐蚀产物进行成分分析可知2A12铝合金的腐蚀产物主要由O,Al,Mg,Cu组成,而7B04铝合金的腐蚀产物主要由O,Al,Mg,Zn组成,腐蚀产物组成不同造成其结构不同,结构的差别使铝合金的点腐蚀行为受到不同的影响。     

防弹陶瓷的研究现状与发展趋势

综述了防弹陶瓷的研究现状,介绍了两种典型的防弹陶瓷。对于Al2O3防弹陶瓷着重于复相结构的分析;对于B4C着重于烧结工艺及陶瓷性能方面的概述。并对防弹陶瓷今后的发展进行了预测,列举了几种较新的防弹陶瓷材料并提出了将纳米复相陶瓷用于防弹方面的设想。     

温度对溶剂热改性C/C复合材料显微结构和氧化性能的影响

以硼酸三正丁酯、乙酸、B2O3粉体为原料,无水乙醇为溶剂,采用一种新颖的溶胶/凝胶结合溶剂热法对C/C复合材料基体进行了抗氧化改性.采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、能量色散谱仪(EDS)及X射线光电子能谱(XPS)对改性后试样进行了表征.重点研究了溶剂热反应温度对改性后试样的物相组成、微观结构和氧化性能的影响.结果表明:经过溶剂热改性处理后,C/C复合材料表面缺陷被玻璃相B2O3组成的涂层所覆盖,材料内部一部分孔隙也被B2O3相填充,且随着溶剂热温度的上升,试样表面的微裂纹逐渐消失,B2O3涂层的致密度上升;C/C基体的抗氧化性能随着溶剂热改性温度(范围353～433 K)的升高而提高;经433 K溶剂热改性后的C/C复合材料在873 K的空气中氧化16 h后的质量损失仅为4.09％.     

低电阻率Si—C—O纤维制备

采用将聚二甲基硅烷与聚氯乙烯共裂解合成制备了Si－C－O纤维先驱体聚合物，并对其进行了表征。表明反应体系中聚氯乙烯含量较高时，生成的先驱体聚合物既有聚碳硅烷的结构特征，又具有－CH＝CH－共轭结构特征的－（SiCH3H-CH2)n（CH＝CH）m－共聚物。先驱体聚合物经熔融纺丝及NO2不熔化处理，高温烧成制得低电阻率Si－C－O（电阻率小于10^0Ω.cm），而通过聚碳硅烷制得的SiC纤维电阻率为10^6Ω.cm。结果表明能够从聚二甲基硅烷与聚氯乙烯共裂解出发制备低电阻率Si－C－O纤维。     

纳米铁酸铜的制备及对RDX热分解的催化作用

以CuCl2·2H2O和Fe(NO3)3·9H2O为原料,采用室温固相化学反应法制备出三种不同铜、铁摩尔质量比的纳米CuFe2O4粉体,产物的粒径约为5nm。采用差示扫描量热法(DSC)测试了纳米CuFe2O4对RDX热分解的催化作用。结果表明:纳米CuFe2O4对RDX热分解有明显的催化效果。在三种纳米CuFe2O4中,铜、铁摩尔质量比为1∶1的纳米CuFe2O4的催化效果最好,它使RDX的分解峰温前移了17 8℃,放热量增加了250J/g,活化能降低了21 9kJ/mol。纳米CuFe2O4的用量增加对RDX热分解的催化效果显著增大。     

一种高W、Mo含量Ni3Al基合金的高温氧化行为

研究了一种高W、Mo的Ni3Al基合金的1050℃静态抗氧化行为,并采用扫描电镜对不同时间氧化后合金的氧化层形貌进行分析,利用X射线衍射仪分析氧化产物的种类和数量,氧化动力学研究表明,合金的氧化动力学曲线不遵循抛物线规律,以W代Mo,能一定程度上改善高Mo的Ni3Al基合金的1050℃抗氧化性能.1050℃/100h静态氧化产物主要为NiO,NiAl2O4和NiWO4,外层氧化镍与内氧化层之间为结合薄弱区,仅氧化1h后,在冷却过程中,该区域就产生大面积开裂,致使外氧化层脱离.随氧化时间增长,合金/氧化层界面的NiAl2O4/Al2O3阻挡层逐步形成,在氧化100h时基本连续,有效降低了合金的氧化速率.     

纳米铜铬复合氧化物对RDX热分解的催化作用

为了研究纳米CuO.Cr2O3复合物的催化性能，采用室温固相化学反应法制备出不同铜、铬质量比的纳米CuO.Cr2O3复合物，测出产物的粒径约为15nm，用DSC测试了纳米CuO.Cr2O3复合物对RDX热分解的催化作用。结果表明．：纳米CuO.Cr2O3复合物对RDX热分解有较好的催化效果，它使RDX的分解峰温提前了11．1℃，活化能降低了17kJ/mol，其作用明显优于纳米CuO和纳米Cr2O3及其混合物。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.