高温合金复杂薄壁零件多道次充液拉深技术

充液拉深(HDD)技术是薄壁零件成形的一种有效方法.针对难成形,复杂薄壁结构的某型发动机高温合金板材零件,通过分析锥面自由悬空区的起皱失稳现象,设计了多道次充液拉深结合刚模成形的技术方案,并建立了有限元分析模型.基于有限元模拟和工艺验证试验,研究了预成形高度和终成形液室压力等关键工艺参数对零件最终成形质量的影响,探讨了...     

Effects of geometrical parameters on wrinkling of thin-walled rectangular aluminum alloy wave-guide tubes in rotary-draw bending

Inner flange and side wrinkling often occur in rotary-draw bending process of rectangular aluminum alloy wave-guide tubes, and the distribution and magnitude of wrinkling is related to geometrical parameters of the tubes. In order to study the effects of geometrical parameters on wrinkling of rectangular wave-guide tubes, a 3D-FE model for rotary-draw bending processes of thin-walled rectangular aluminum alloy wave-guide tubes was built based on the platform of ABA-QUS/Explicit, and its reliability was validated by experiments. Simulation and analysis of the influence laws of geometrical parameters on the wave heights of inner flange and side wrinkling were then carried out. The results show that inner flange wrinkling is the main wrinkling way to rectan- gular wave-guide tubes in rotary-draw bending processes, but side wrinkling cannot be neglected because side wrinkling is 2/3 of inner flange wrinkling when b and h are smaller. Inner flange and side wrinkling increase with increasing b and h; the influence of b on side wrinkling is larger than that of h, while both b and h affect inner flange wrinkling greatly. Inner flange and side wrinkling decrease with increasing R/h; the influence of h on inner flange and side wrinkling is larger than that of R.     

Deformation behaviors of four-layered U-shaped metallic bellows in hydroforming

Because of the complex constraint effects among layers in multi-layered metallic bellows hydroforming, the stress concentration and defects such as wrinkling and fracture may easily occur. It is a key to reveal the deformation behaviors in order to obtain a sound product. Based on the ABAQUS platform, a 3D-FE model of the four-layered U-shaped metallic bellow hydroforming process is established and validated by experiment. The stress and strain distributions, wall thickness variations and bellow profiles of each layer in the whole process, including bulging, folding and springback stages, are studied. Then deformation behaviors of bellows under different forming conditions are discussed. It is found that the wall thinning degrees of different layer vary after hydroforming, and is the largest for the inner layer and smallest for the outer layer. At folding stage, the wall thinning degree of the crown point increases lineally, and the difference among layers increases as the process going. The displacements of the crown point decrease from the inner layer to the outer layer. After springback, the U-shaped cross section changes to a tongue shape, the change of convolution pitch is much larger than the change of convolution height, and the springback values of the inner layer are smaller than the outer layer. An increase in the internal pressure and die spacing cause the maximum wall thinning degree and springback increase. With changing of process parameters, bellows with deep convolution are easily encountered wall thinning during hydroforming and convolution distortion after springback. This research is helpful for precision forming of multi-layered bellows.     

运动油滴/固体壁面斜碰撞的状态辨识及特征分析

 航空发动机轴承腔油气两相流动与换热研究是轴承腔润滑与换热设计的重要基础工作,而运动油滴与轴承腔壁面的碰撞状态辨识及特征分析是轴承腔油气两相流动与换热研究的组成部分。基于VOF方法建立了运动油滴与固体壁面斜碰撞数值仿真模型,实现了运动油滴与固体壁面斜碰撞状态的数值模拟,分析了碰撞油滴直径、入射角和碰撞速度对沉积油膜铺展长度、油膜堆积厚度和溅射油滴数目等碰撞状态特征参数的影响规律,提出了运动油滴与固体壁面斜碰撞条件下的状态判断准则,并得到了文献的物理试验工作的支持。研究结果表明:随着油滴入射角减小,沉积油膜铺展长度和油膜堆积厚度增大,溅射油滴数目减少;随着碰撞速度和油滴直径的增大,沉积油膜铺展长度和溅射油滴数目均增大,但油膜堆积厚度对应前者呈减小趋势、对应后者仍呈增大趋势。     

A Study on Multi-defect Constrained Bendability of Thin-walled Tube NC Bending Under Different Clearance

Thin-walled tube numerical control (NC) bending is a tri-nonlinear physical process with multi-defect and multi-die constraints. The clearance on each contact interface is the major factor to indicate the contact conditions. A three-dimensional-finite element (3D-FE) model is established to consider the realistic dynamic boundary conditions of multiple dies under ABAQUS/Explicit platform. Combined with experiment, numerical study on bending behavior and bendability under different clearance between tube and various dies is conducted in terms of wrinkling, wall thinning and cross section deformation. The results show that (1)with smaller clearance of tube-wiper die and tube-mandrel, the wrinkling can be restrained while the wall thinning It and cross-section deformation Id increase; while excessive small clearance blocks tube materials to flow past tangent point and causes piles up, the onset of wrinkling enhances It and Id. (2)Both It and Id decrease with smaller clearance of tube-pressure die; the wrinkling possibility rises with larger clearance on this interface if the mandrel’s freedom along Y-axis is opened; smaller clearance of tube-bend die prevents wrinkling while increases It, and the clearance on this interface has little effect on Id. (3)A modified Yoshida buckling test (YBT) is used to address the wrinkling mechanisms under normal constraints in tube bending: the smaller clearance may restrain wrinkling efficiently; the smaller wall thickness, the less critical clearance needed; the critical clearance for tube bending 38 mm×1 mm×57 mm (tube outer diameter×wall thickness×centerline bending radius) equals about 20% of initial wall thickness.     

倾斜射流撞壁形成的液膜外形的理论建模

倾斜射流撞击壁面在燃烧室液膜冷却、溅板式喷注器雾化等领域均有广泛应用.为了研究倾斜射流撞壁形成的液膜的基本形态、液膜边界大小,开展理论建模研究.通过建立在液膜边界的守恒方程及液膜在壁面上的厚度及速度分布关联式,形成一套能够求解倾斜射流撞击壁面后液膜形态及边界的理论方法.模型计算结果与文献中的实验结果对比表明,建立的模型...     

液滴冲击移动液膜的数值研究

为了研究液滴冲击移动液膜问题,建立了三维不可压缩层流计算模型,基于耦合的水平集-流体体积法对两相界面进行追踪,探讨了液膜速度和厚度、液滴直径和速度对冲击移动液膜过程的影响。研究表明:液膜静止时,冲击结果是对称的,而液膜移动时,冲击结果变为非对称;液膜速度对冠上游生长具有增强效应,而对冠下游具有抑制作用,增加液膜速度冠的上游高度增加、下游高度减小,内径增加;液膜厚度增加,液膜与壁面的粘性损失减小,吸收冲击动能的能力增强,当无量纲液膜厚度小于1时,冠的上、下游高度均随着液膜厚度的增加而增加,否则相反;当无量纲液膜厚度小于0.5时,冠内径随着液膜厚度的增加而增加,否则反之;随液滴直径和速度的增大,冠的高度和内径均增加。     

Investigation of anode shaping process during co-rotating electrochemical machining of convex structure on inner surface

A novel co-rotating electrochemical machining method is proposed for fabricating convex structures on the inner surface of a revolving part. The electrodes motion and material removal method of co-rotating electrochemical machining are different from traditional electrochemical machining. An equivalent kinematic model is established to analyze the novel electrodes motion,since the anode and cathode rotate in the same direction while the cathode simultaneously feeds along the line of centres. Acc...     

冲压发动机超薄壁波纹形件的粘性介质压力成形

粘性介质压力成形是一种采用具有高粘度并且可流动的半固态介质作为软凸模的成形方法。采用试验和数值模拟方法，研究了高温合金超薄壁波纹形件成形过程坯料形状、应变分布、厚度分布的变化和界面摩擦对板料成形的影响，研究结果表明：成形件尺寸精度高、表面质量好、厚度均匀；与钢凸模成形相比较，可以避免局部较小半径曲面之间的严重颈缩；对于具有局部较小半径曲面的复杂形状薄壁件，粘性介质压力成形显示出其优越性。     

Radially loading rotary extrusion for manufacturing large-size conical cylinders with inner transverse high ribs

The Large-size Conical Cylinders with Inner Transverse High Ribs (LCCWITHR) can reduce the weight of the parts while maintaining high rigidity and strength. Radially Loading Rotary Extrusion (RLRE) forming technology can achieve integral forming of LCCWITHR through the synergy of radial and rotary movements of dies. The flow law of the material during the forming process is the key to forming large-size inner ribs. At present, there is no unified understanding of the metal flow law of RLRE forming technology. An analytical expression was derived to predict the Radial Direction (RD) deformation loads. The FE simulation and process experiment were carried out to investigate the effects of the inclination angle, thickness factor and transition arc radius of the split top dies on the spacing of the metal diversion plane, the metal flow velocity of the rib area and the final radius of the inner rib. The influence of the split top dies loading distance and the bottom die rotation angle of each pass on the inner radius of the inner rib was verified. And the optimal combination of dies shape parameters and loading paths which can make the metal flow orderly was obtained: the inclination angle is 140°, the thickness factor is 3.64, the transition arc radius is 16 mm; the top dies loading distance is 15 mm, the bottom die rotation angle is 45°. The FE simulation results have been found to be in close agreement with physics experiment. The research results reveal the metal flow law of rib growth in the RLRE of LCCWITHR, which lays a theoretical foundation for subsequent thorough research and process optimization.     

A theoretical method for solving shock relations coupled with chemical equilibrium and its applications

In this study, a theoretical method is proposed to solve shock relations coupled with chemical equilibrium. Not only shock waves in dissociated flows but also detonation waves in combustive mixtures can be solved. The global iterative solving process is specially designed to mimic the physical and chemical process in reactive shock waves to ensure good stability and fast convergence in the proposed method. Within each global step, the single-variable equations of normal and oblique shock relatio...     

复杂异形截面薄壁环形件动模液压成形研究

 液压成形技术是成形薄壁零件的一种有效的解决方法。针对具有异形截面结构的某型发动机高温合金薄壁环形件,提出了液压成形结合动模轴向加载的复合成形方法,依据塑性力学方法和增量理论对成形过程进行了应力应变特征分析,并建立了有限元模型。基于有限元模拟和工艺试验,研究了筒坯成形区高度和型腔液压加载路径等关键工艺参数对零件成形结果的影响,探讨了成形过程中壁厚过度减薄、材料堆积"折叠"、形状不对称等失效形式,提出了优化的工艺参数。结果表明,提出的工艺方法可实现复杂异形截面薄壁环形件的整体精确成形,采用优化的筒坯成形区高度和液压加载路径可获得壁厚分布均匀、成形质量较好的零件。     

Modelling and analysis of metal flowing behaviors in constraining ring rolling of tapered ring with thin wall and three high ribs

Tapered ring with thin wall and three high ribs(TRTWTHR), showing complicated geometry(wall thickness is less than 4 mm and rib height exceeds 20 mm), is extensively utilized to fabricate the critical structural parts of aerospace equipment such as spacecraft cabin, rocket body and fuel tank because of light weight and high carrying capacity. How to fabricate TRTWTHR with high performance is a critical problem that aerospace area needs to solve. In this work, constraining ring rolling(CRR) techn...     

Investigation of hot jet on active control of oblique detonation waves

The hot jet injection is utilized to actively control the oblique detonation wave, such as initiating and stabilizing an oblique detonation wave at a desired position that is shorter than the length of induction zone, and adjust the height of the oblique detonation wave at the exit of combustor when the oblique detonation wave engine is working on off-design flight conditions. The fifth order Weighted Essentially Non-Oscillatory (WENO) scheme and a two-step reversible reaction mechanism of the stoichiometric H₂/Air are adopted in the simulations. With the help of hot jet injection, the transition from inert oblique shock wave to the oblique detonation wave immediately occurs near the position of hot jet injection, and consequently the length of combustor can be reduced. The angle of oblique detonation wave also decreases as the hot jet injection approaches the nose of wedge. Additionally, the height of the oblique detonation wave at the exit of combustor can be flexibly adjusted, and also depends on the injection position and the strength of the hot jet. If the velocity of the hot jet is too weak to directly trigger the overall oblique detonation wave at the position of injection, increasing the injection pressure will improve the strength of the hot jet and results in a successful transition.     

2524铝合金的搅拌摩擦焊对接工艺

以2524-T3板材作为试验材料,研究了薄板的搅拌摩擦焊对接工艺,优化了对接焊的工艺参数,获得了焊接工艺窗口及最优工艺参数.在最优工艺参数下生产的对接焊件具有良好的质量外观,焊件的变形量和焊缝减薄量极小;焊件的X射线检测结果表明焊件内部质量良好,没有在照片上发现缺陷;金相组织分析显示,焊缝横截面组织均匀致密;焊接接头静力拉伸性能测试结果表明焊缝抗拉强度的平均为397 MPa,为母材抗拉强度的90.4％.     

基于加工误差仿真的半球谐振子优化设计

针对半球谐振陀螺谐振子制造过程中存在的加工误差,采用有限元仿真,分析了半球谐振子结构参数、尺寸公差和形位公差变化对其工作模态频率和临近模态频率的影响,研究了半球谐振子形位公差变化对频率裂解和品质因数的影响。通过仿真分析可知,半球谐振子结构参数壁厚、半球中心半径及内倒角半径都会影响模态频率;半球谐振子形位公差中的内外球心距离误差对其工作模态影响较大,中心轴平行误差对频率裂解和品质因数影响较大;半球谐振子壁厚、内倒角半径、小柱半径及内外球心距离误差变化会使工作模态频率与相邻模态间存在干扰。在此基础上,提出了半球谐振子结构参数及形位公差优化设计建议,并通过半球谐振子品质因数Q值和频率裂解测量对该建议进行了验证。     

纤维缠绕压力容器的可靠性分析

文摘运用一次二阶距(FOSM)法,对纤维缠绕复合材料压力容器进行了可靠性分析,并与传统网格理论设计法进行了对比,讨论了纤维拉伸强度、爆破压力、压力容器半径、纤维缠绕层总厚度及缠绕角的变异系数对纤维强度发挥系数和压力容器壁厚的影响。结果表明:随着各设计参数变异系数的均匀增大,纤维强度发挥系数迅速减小,压力容器壁厚迅速增大;缠绕角度和纤维拉伸强度的变异系数对它们的影响最为显著。     

基于ICT图像的航空发动机涡轮叶片壁厚尺寸精密测量方法

为保障航空发动机的可靠性,要求精确测量发动机叶片不同界面处的内、外表面法线方向的厚度。为此,研究了一种基于ICT图像的叶片壁厚尺寸亚像素级精密测量方法。它采用边界提取技术确定叶片内、外表面法线的方向;应用亚像素级边界定位技术,在该法线方向,定位壁厚的起始边界点和终止边界点;然后,计算两个边界点坐标位置差,获得以像素为单位的壁厚尺寸;最后,对像素尺寸进行标定,获得以毫米为单位的壁厚尺寸。试验结果表明,本文方法实际测量精度达到0.2个像素和0.042mm。     

Plastic wrinkling prediction in thin-walled part forming process:A review

The precision forming of thin-walled components has been urgently needed in aviation and aerospace field. However, the wrinkling induced by the compressive instability is one of the major defects in thin-walled part forming. The initiation and growth of the wrinkles are interac-tively affected by many factors such as stress states, mechanical properties of the material, geometry of the workpiece and boundary conditions. Especially when the forming process involves compli-cated boundary conditions such as multi-dies constrains, the perturbation of clearances between workpiece and dies and the contact conditions changing in time and space, etc., the predication of the wrinkling is further complicated. In this paper, the current prediction methods were summa-rized including the static equilibrium method, the energy method, the initial imperfection method, the eigenvalue buckling analysis method, the static-implicit finite element method and the dynamic-explicit finite element method. Then, a systematical comparison and summary of these methods in terms of their advantages and limitations are presented. By using a combination of explicit FE method, initial imperfection and energy conservation, a hybrid method is recommended to predict plastic wrinkling in thin-walled part forming. Finally, considering the urgent requirements of com-plex thin-walled structures’ part in aviation and aerospace field, the trends and challenges in wrin-kling prediction under complicated boundary conditions are presented.     

膨胀规律可控的轴对称基准流场设计方法

为了提高流线追踪喷管设计方法的灵活性,从推力和力矩两方面考虑,引入特殊中心体,探索了壁面膨胀规律可控的轴对称基准流场设计方法.设计过程中利用特征线理论（MOC）实现了由膨胀规律求解气动壁面的反设计.针对基准流场的主要设计参数,包括膨胀规律、中心体及斜倾角等进行了参数化研究,得到了设计参数对基准流场结构及性能的影响规律.利用该基准流场,设计了矩形截面的流线追踪喷管(导出喷管),并进行了分析.结果表明:利用特征线理论可以实现膨胀规律到壁面的反设计;在进口参数和落压比一定的条件下,存在一定的膨胀规律使得基准流场的内推力最大;流场的中心体尺度和长度比对推力影响很小,可作为调整导出喷管力矩的设计参数;出口斜倾角增大会导致基准流场的长度减小,同时推力下降明显,设计时应综合考虑.