Radar CFAR Thresholding in Clutter and Multiple Target Situations

Radar detection procedures involve the comparison of the received signal amplitude to a threshold. In order to obtain a constant false-alarm rate (CFAR), an adaptive threshold must be applied reflecting the local clutter situation. The cell averaging approach, for example, is an adaptive procedure. A CFAR method is discussed using as the CFAR threshold one single value selected from the so-called ordered statistic (this method is fundamentally different from a rank statistic). This procedure has some advantages over cell averaging CFAR, especially in cases where more than one target is present within the reference window on which estimation of the local clutter situation is based, or where this reference window is crossing clutter edges.     

Optimal CFAR detection in Weibull clutter

Optimal, in the maximum likelihood sense, constant false-alarm rate (CFAR) detection for Weibull clutter statistics, is investigated. The proposed OW (optimal Weibull) estimator is proved to be an asymptotically efficient estimator of the mean power of the Weibull clutter. Theoretical analysis of the OW-CFAR detector is provided, while detection performance analysis is carried out using the Monte Carlo simulation method. The operation of the median and morphological (MEMO)-CFAR detector in Weibull clutter statistics is also explained. It performs almost optimally in uniform clutter and, simultaneously, it is robust in multitarget situations. The performance of the proposed OW-CFAR detector in uniformal Weibull clutter is used as a yardstick in the analysis of the MEMO cell-averager (CA) and ordered statistic (OS) CFAR detectors. Nonfluctuating and fluctuating (Swerling II) targets are considered in detection analysis. The performance of the detectors is also examined at clutter edges     

A new and robust CFAR detection algorithm

A constant false alarm rate (CFAR) detection method which is based on a combination of median and morphological filters (MEMO) is proposed. The MEMO algorithm has robust performance with small CFAR loss, very good behavior at clutter edges and high detection performance in the case of closely spaced narrowband signals (targets). The proposed MEMO method is favourably compared with cell averaging (CA) and ordered statistics (OS) CFAR detectors. The Monte Carlo method is employed to analyze the MEMO-CFAR detector     

Performance of MAX family of order-statistic CFAR detectors

The MAX family of constant-false-alarm-rate (CFAR) detectors is introduced as a generalization of the greatest of CFAR (GO-CFAR) or MX mean-level detector (MX-MLD). Members of the MAX family use local estimators based on order statistics and generate both a near-range and a far-range noise-level estimate. Local estimates are always combined through a maximum operation; this insures false-alarm control at clutter edges. At the same time, order-statistic-based estimators result in a high-resolution detector. A complete detection analysis is provided for SWII targets and a reference channel contaminated by large outliers. Results are presented for the MX censored MLD (MX-CMLD) operating in clutter. The MX order statistic detector (MX-OSD) based on only a single-order statistic per window, is analyzed, and curves showing the required threshold, CFAR loss, optimum censoring point, and signal-to-noise ratio (SNR) loss in the presence of outliers are given. Simulations are used to compare the dynamic responses of various MX-OSD detectors in a clutter and a multiple-target environment     

Data quantization effects in CFAR signal detection

In this paper, we investigate data quantization effects in constant false alarm rate (CFAR) signal detection. Exponential distribution for the input data and uniform quantization are assumed for the CFAR detector analysis. Such assumptions are valid in the case of radar for a Swerling I target in Gaussian clutter plus noise and a receiver with analog square-law detection followed by analog-to-digital (A/D) conversion. False alarm and detection probabilities of the cell averaging (CA) and order statistic (OS) CFAR detectors operating on quantized observations are analytically determined. In homogeneous backgrounds with 15 dB clutter power fluctuations, we show analytically that a 12-bit uniform quantizer is sufficient to achieve false alarm rate invariance. Detector performance characteristics in nonhomogeneous backgrounds, due to regions of clutter power transitions and multiple interfering targets, are also presented and detailed comparisons are given     

Ll-CFAR: a flexible and robust alternative

A new family of constant false alarm rate (CFAR) processors is introduced. An Ll-CFAR forms its noise power estimate by linearly filtering ranked samples from the reference set; the weights of this combination, however, depend not only on the rank, but also on the relative proximity of the sample to the cell under test. From the class of Ll-CFARs may be chosen members which effectively censor spurious targets; members which exhibit impressive control of false alarm in the presence of a clutter edge; and members which are robust against both such inhomogeneities. While the design of such schemes is involved, their implementation is not significantly more burdensome than that of plain ordered statistic CFAR (OS-CFAR). After a discussion of the stochastic training of Ll-CFAR, the performance is thoroughly assessed under the most commonly encountered instances of environmental conditions, and compared with those of classical CFAR techniques     

Distributed CFAR detection in homogeneous and nonhomogeneousbackgrounds

The performance of distributed constant false alarm rate (CFAR) detection with data fusion both in homogeneous and nonhomogeneous Gaussian backgrounds is analyzed. The ordered statistics (OS) CFAR detectors are employed as local detectors. With a Swerling type I target model, in the homogeneous background, the global probability of detection for a given fixed global probability of false alarm is maximized by optimizing both the threshold multipliers and the order numbers of the local OS-CFAR detectors. In the nonhomogeneous background with multiple targets or clutter edges, the performance of the detection system is analyzed and its performance is compared with the performance of the distributed cell-averaging (CA) CFAR detection system     

基于杂波对消-自聚焦的多通道SAR-GMTI

对超高频(UHF)波段多通道合成孔径雷达(SAR)动目标检测技术进行研究,解决了长相干积累时间导致动目标在方位向散焦严重的问题。采用分块自聚焦技术对多通道SAR地面移动目标指示(GMTI)系统自适应杂波抑制后的SAR图像进行处理,改善杂波抑制后的SAR图像中动目标的聚焦情况,增强动目标与周围剩余杂波的对比度,进而提高恒虚警率(CFAR)检测的性能。与传统杂波抑制后直接进行CFAR检测方法相比较,该方法降低了检测虚警概率。实测数据处理结果显示动目标的信杂比明显提高,动目标方位向聚焦成功,证明了该方法的有效性。     

CFAR data fusion center with inhomogeneous receivers

Detection systems with distributed sensors and data fusion are increasingly used by surveillance systems. A system formed by N inhomogeneous constant false alarm rate (CFAR) detectors (cell-averaging (CA) and ordered statistic (OS) CFAR detectors) is studied. A recursive formulation of an algorithm that permits a fixed level of false alarms in the data fusion center is presented, to set the optimum individual threshold levels in the CFAR receivers and the optimum `K out of N' decision rule in order to maximize the total probability of detection. The algorithm also considers receivers of different quality or with different communication channel qualities connecting them with the fusion center. This procedure has been applied to several hypothetical networks with distributed CA-CFAR and OS-CFAR receivers and for Rayleigh targets and interference, and it was seen that in general the fusion decision OR rule is not always the best     

Radar modelling to improve CFAR performance in the littoral

Littoral operation of radars poses severe signal processing difficulties due to the highly stressing, inhomogeneous clutter. This report describes an initial investigation into the feasibility of utilising site specific radar modelling to provide a localized estimate of the clutter statistics which can then be used to predict the required threshold to maintain a given false alarm rate. The technique has been applied to littoral clutter recordings obtained from the experimental S-band phase array radar, MESAR2. Results are presented for the technique in comparison with a conventional, non-adaptive, cell averaging CFAR. The paper concludes that significant performance enhancements are possible through the use of this new technique.     

Improved CFAR performance in the littoral

Littoral operation of radars poses severe signal processing difficulties due to the highly stressing, inhomogeneous clutter. This report describes an initial investigation into the feasibility of utilising site-specific radar modelling to provide a localised estimate of the clutter statistics which can then be used to predict the required threshold to maintain a given false alarm rate. The technique has been applied to littoral clutter recordings obtained from the experimental S-band phased array radar, MESAR2. Results are presented for the technique in comparison with a conventional, non-adaptive, cell averaging CFAR. This paper concludes that significant performance enhancements are possible through the use of this new technique.     

非相干Rice杂波中的恒虚警检测

 地杂波的统计特性常常可以用Rice模型来描述,其物理基础是认为地杂波由一些大的固定散射体引起的稳定分量和大量小的随机分布的运动散射体引起的瑞利起伏分量所合成。文献[2]研究了稳定分量不相干时Rice杂波中离散时间最佳检测的估值器——相关器结构,但无显式解,实现有困难。文献[3]导出了Rice杂波中SwerlingⅡ目标的离散时间检测的似然比检测器结构。在此基础上,本文给出了一种修正平方律结构的似然比检测器,并和通常的平方律检测器作了性能比较。     

A variably trimmed mean CFAR radar detector

A variably trimmed mean (VTM) constant false alarm rate (CFAR) detector in which the threshold is determined by processing a linear combination of a group of ordered samples in each window is introduced. Unlike the trimmed mean detector, the number of ordered samples that require further processing is allowed to vary according to a data-dependent rule. It is demonstrated that the VTM detector exhibits performance characteristics that are independent of the total (stationary) noise power. Simulated performance results are presented for regions of clutter power transitions and for multiple target environments to illustrate the possible improvement over the order-statistic detector that can be obtained by using a VTM detector     

Analysis of CFAR processors in homogeneous background

Five different constant false alarm rate (CFAR) radar processing schemes are considered and their performances analyzed in homogeneous and nonhomogeneous backgrounds, the latter specifically being the multiple target environment and regions of clutter transitions. The average detection threshold for each of the CFAR schemes was computed to measure and compare the detection performance in homogeneous noise background. The exponential noise model was used for clear and clutter backgrounds to get closed-form expressions. The processor types compared are: the cell-averaging CFAR, the `greatest of' CFAR, the `smallest of' CFAR, the ordered-statistics CFAR, and a modified ordered-statistics processor called the trimmed-mean CFAR     

Matched subspace CFAR detection of hovering helicopters

A constant false alarm rate (CFAR) strategy for detecting a Gaussian distributed random signal against correlated non-Gaussian clutter is developed. The proposed algorithm is based on Scharf's matched subspace detector (MSD) and has the CFAR property with respect to the clutter amplitude probability density function (apdf), provided that the clutter distribution belongs to the compound-Gaussian family and the clutter covariance matrix is known to within a scale factor. Analytical expressions of false alarm and detection probabilities are derived. An application to the problem of detecting hovering helicopters against vegetated ground clutter is reported     

非高斯杂波下自适应雷达目标检测新方法

在球不变随机向量(SIRV)非高斯杂波背景下,研究了多脉冲相参雷达目标的自适应检测问题。假设杂波具有相同的协方差矩阵结构和可能相关的纹理分量,提出了新的协方差矩阵估计器,并获得了相应的自适应归一化匹配滤波器(ANMF)。理论分析表明,在估计杂波分组大小与实际情况匹配时,所获得的ANMF对杂波功率水平和协方差矩阵结构均具有恒虚警率(CFAR)特性。仿真结果表明:当估计的杂波分组大小失配时,所获得的ANMF具有近似CFAR特性,并进一步分析了不同参数变化对所提检测器性能的影响。与已有的ANMF相比,所获得的ANMF具有更好的检测性能,且迭代次数更小,其相对于已知杂波协方差矩阵的最优归一化匹配滤波器(NMF)的检测损失也更小,具有很好的实际应用前景。     

Ordered Statistic CFAR Processing for Two-Parameter Distributions with Variable Skewness

Rohling has developed a constant false alarm rate (CFAR) technique based on ordered statistics of the reference cells. An extension of his technique is presented that maintains a CFAR for two-parameter distributions, with both mean power and skewness variable. The new method is therefore more robust, but has higher CFAR loss than the single-parameter technique.     

Performance of max-mean level detector with and without censoring

The maximum-mean-level detector (MX-MLD) is a constant false-alarm rate (CFAR) detector designed to eliminate the excessively high false-alarm rate seen with the MLD at the edges of contiguous clutter regions. The concomitant high target suppression effect led M. Weiss (1982) to suggest a censored modification. The authors analyze the detection performance of the maximum-censored-mean-level detector (MX-CMLD). A homogeneous Swerling II target and clutter environment are assumed, and only single-pulse detection is considered. Analytic results apply equally to the MX-MLD and extend previous analysis. Simulation results are presented that demonstrate the qualitative effects of various CFAR detectors in nonhomogeneous clutter environments     

Statistical analyses of measured radar ground clutter data

The performance of ground-based surveillance radars strongly depends on the distribution and spectral characteristics of ground clutter. To design signal processing algorithms that exploit the knowledge of clutter characteristics, a preliminary statistical analysis of ground-clutter data is necessary. We report the results of a statistical analysis of X-band ground-clutter data from the MIT Lincoln Laboratory Phase One program. Data non-Gaussianity of the in-phase and quadrature components was revealed, first by means of histogram and moments analysis, and then by means of a Gaussianity test based on cumulants of order higher than the second; to this purpose parametric autoregressive (AR) modeling of the clutter process was developed. The test is computationally attractive and has constant false alarm rate (CFAR). Incoherent analysis has also been carried out by checking the fitting to Rayleigh, Weibull, log-normal, and K-distribution models. Finally, a new modified Kolmogorov-Smirnoff (KS) goodness-of-fit test is proposed; this modified test guarantees good fitting in the distribution tails, which is of fundamental importance for a correct design of CFAR processors     

常用雷达视频信号处理算法在FPGA上的实现

采用FPGA技术对雷达原始的视频信号进行求模、视频积累与恒虚警检测处理,克服了DSP处理速度有限、实时性差和ASIC器件灵活性差的问题。详细介绍了求模、视频积累以及恒虚警算法在FPGA芯片上实现的原理和过程,并结合仿真结果说明了利用FPGA进行雷达视频信号处理的优势。