Implementation of a single-phase AC/AC converter based on neutral-point-clamped topology

A single-phase ac/ac converter based on neutral-point-clamped scheme is proposed to perform unity input power factor and to provide a stable ac voltage to the critical loads. The ac/dc rectifier part is controlled to generate a unipolar pulsewidth modulation (PWM) waveform on the ac terminal by using four power switches with voltage stress of half the dc-link voltage. The carrier-based current control scheme is employed in the inner control loop to track the line current command. To regulate the dc bus voltage, a proportional-integral (PI) control is adopted in the outer control loop. The dc/ac inverter part of the system with four power switches is employed to generate a stable and clean sinusoidal output voltage to the critical load. The instantaneous current control scheme is used to track the output voltage command. To verify the effectiveness of the proposed control algorithm, the simulation and experimental results based on a laboratory prototype were implemented and discussed.     

Single-phase three-level rectifier and random PWM inverter drives

A novel ac/dc/ac converter topology with three-level pulsewidth modulated (PWM) scheme for the single-phase ac/dc rectifier and random PWM scheme for ac drives is proposed. In order to improve the power quality in the single-phase rectifier, a ROM-based (read-only memory) control scheme, based on hysteresis current comparator, region detector, and capacitor compensator, is used to achieve a sinusoidal line current with low current distortion. The control scheme of the adopted three-level rectifier is easy to implement. The blocking voltage of power switches is clamped to half of the dc bus voltage. To reduce the mechanical vibration from an induction motor, random pulse position PWM scheme is adopted to spread the harmonics in a wide frequency range which results in the reduction of torque pulsation in the ac motor drives. Simulation and experimental results based on the laboratory prototype circuit are presented to verify the proposed control scheme     

Implementation of nondeterministic pulsewidth modulation forinverter drives

A single-phase power factor preregulator to improve the power quality in the input side of an ac/dc/ac converter and a random pulsewidth modulation (PWM) to reduce the emitted noise energy and the mechanical vibration for an induction motor drive is proposed. The hysteresis current control (HCC) technique for a voltage source switching mode rectifier (SMR) is adopted. A control scheme is presented such that the line current is driven to follow the reference current which is derived from the dc bus voltage regulator and the output power estimator. A random pulse position technique for a three-phase voltage source inverter system to reduce the noise energy and resonant vibration from ac machine drive is described. By randomly varying the instantaneous pulse position in each switching frequency, the frequency distribution of harmonics is spread in a wide frequency range which results in reduction of torque pulsations in the ac motor drive systems. To investigate the proposed control scheme, experimental tests based on a laboratory prototype were implemented to show the nearly unity power factor at the SMR and reduce the noise energy concentrated at the specific tones     

Novel single-stage half-bridge series-resonant buck-boost inverter

A novel single-stage half-bridge series-resonant buck-boost inverter (HB-SRBBI) is proposed. The main attribute of the novel inverter topology is the fact that it generates an ac output voltage larger or lower than the dc input one, depending on the instantaneous duty cycle. This property is not found in the classical voltage source inverter (VST), which produces an ac output instantaneous voltage always lower than the dc input voltage. The proposed inverter circuit topology provides the main switch for turn-on at zero-current-switching (ZCS) by an auxiliary resonant cell built before the output choke. A state-space averaging approach is employed to analyze the system. A design example of 500 W ac/dc inverter is examined to assess the inverter performance and it provides high power efficiency above 90.7% under the rated power.     

Certain System Aspects of the Double-Sided Cyclo-Converter

A philosophy for the improvement of the extraction of controlled dc power from a polyphase ac supply line is presented. Extension of this philosophy for the interface of synchronous polyphase networks is briefly indicated. The needed kilovolt-ampere capacity of the supply line is reduced to nearly two thirds of the capacity needed for conventional controlled ac/dc converter systems. The new system requires only a small fraction of the physical weight of conventional converters. The improvements are derived from the interposition of a modulated high-power frequency carrier between the linked systems for the purpose of reconciliation of their conflicting characteristics. The harmonic content of the ac-phase currents is greatly reduced. The system operates with internal frequencies near 10 kHz; efficiencies in the upper nineties have been attained with this type of converter.     

Novel AC line conditioner for power factor correction

A new ac line conditioner is presented for high input power factor and clean ac output voltages for isolating the linear or nonlinear loads. A three-phase two-leg switching mode rectifier with neutral-point-clamped topology is proposed to draw the sinusoidal line currents from the ac mains. The carrier-based current controller is used in the inner control loop to track the line current commands with unity power factor. The dc bus voltage controller is adopted in the outer control loop to regulate the dc-link voltage. A voltage compensator is used to balance the neutral point voltage on the dc tank. A three-phase two-leg inverter with neutral-point-clamped topology is adopted in the system to provide the clean ac output voltages to the critical or sensitive loads. The carrier-based current control scheme is adopted to improve the instantaneous output voltages. Experimental results show the validity and effectiveness of the proposed control strategy.     

A new power collection architecture for future spacecraft

The generalized tree-like transmission line network system having n layers in total with m-to-1 branch connection at each joint (T-TLNS-n-m) is proposed to replace the traditional series-parallel combined dc networks to automatically accumulate identically distributed power cells into the large amount of useful power for the spacecrafts. The proposed system has the attractive features of simple structure, easy construction and maintenance, and low cost, because two kinds of parts, ac current sources and m-to-1 transmission line (TL) branch connection parts, are used in the whole system. A method of implementing ac current cells having high output impedance is proposed to improve the power collection efficiency of the whole network system. Simulated results show that that low-pass nominal /spl pi/- or T-circuit with high characteristic impedance, which is used for the voltage source to current source converter in the current cell, improves the efficiency of the voltage inverter, filters out the harmonics, and increases the output impedance of the whole current cell.     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Describing Function Properties of a Magnetic Pulsewidth Modulator

An analysis is presented for the transfer functions of a particular pulsewidth modulator and power-stage subsystem that has been widely used in practical switching-mode dc regulator systems. The switch and filter are in a ?buck? configuration, and the switch is driven by a constant-frequency, variable duty-ratio, push-pull magnetic modulator employing square-loop cores. The two transfer functions considered are that with modulator control signal as input and that with line voltage as input. For ac signal,the corresponding describing functions (DF) are derived. It is shown thatcurrent-source drive to the modulator extends the control DF frequency response over that with voltage drive, and that complete cancellation of the effects of line variations can be obtained at dc, but not for ac. Experimental confirmation of the analytical results for the control DF are presented.     

Half-bridge neutral point diode clamped rectifier for power factor correction

A high power factor rectifier based on neutral point clamped scheme is proposed. The voltage stress of each power semiconductor of the adopted rectifier is equal to the half dc bus voltage instead of full dc link voltage in the conventional switching mode rectifier. The control signals of the power switches are derived from the dc link voltage balance compensator, line current controller, and dc link voltage regulator. The hysteresis current control scheme is employed to draw a clean sinusoidal line current, high input power factor, regulated dc link voltage, and balance capacitor voltages. Three voltage levels are generated on the ac terminal of the adopted rectifier. To verify the proposed operation scheme, performance characteristics are given by the experimental results.     

Frequency-controlled series-resonant converter with synchronous rectifier

This paper presents an analysis and experimental results for a frequency-controlled series-resonant dc-dc converter that consists of a Class-D zero-voltage-switching (ZVS) series-resonant inverter and a center-tapped synchronous rectifier. If the dc output voltage is low, the efficiency of the converter is dominated by the efficiency of the rectifier. Low on-resistance metal-oxide-semiconductor field-effect transistors (MOSFETs) are used in the rectifier instead of diodes because the forward voltage drop across the rectifying device is low, resulting in a high efficiency. The dc output voltage is regulated against variations in the load resistance and the dc input voltage by varying the operating frequency. Experimental results are presented for a converter with a dc input voltage of 150 V, an output voltage of 5 V, and a dc load resistance ranging from 0.5 to 5.5 R. The measured efficiency was 86% for a 50 W output and 89% for a 25 W output. The theoretical results were in good agreement with the measured results.     

用Walsh函数方法的阶梯波式DC/AC变换器的设计与实现

讨论了阶梯波式 DC/AC变换器的一种新的设计与实现方法 ,即用 Walsh函数方法及矢量合成原理分析、综合和设计。试验结果表明实现了逆变器结构的简化及其输出电压频率稳定 ,幅值便于调节与自动稳定。给出了有关硬件、软件框图与说明、试验结果及进一步设想     

A parallel computer architecture for continuous simulation

A parallel computer specifically designed for the solution of ordinary differential equations is described. The first version of the machine contains thirty-two processors, running in an asynchronous multiple-instruction/multiple-data mode, communicating with high-speed parallel busses. Synchronization is accomplished by a microprogrammable communication controller. A number of processors have been designed and built for the machine. The processor types offer a wide variation in solution speed and accuracy. To permit easy comparisons with analog and hybrid systems, performance is measured by finding the highest frequency sine wave which can be integrated in real time with an accuracy of 0.1% or higher. Using this performance measure the performance limit of the current machine is 2000 Hz. The structure is capable of solving systems described by differential equations up to order sixty-four at these performance limits     

Stepped Sinewave Inverter

A stepped sinewave dc/ac inverter was analyzed for an inductive load with respect to load current and voltage, harmonics, power factor, and efficiency. This special inverter of high efficiency and low harmonic content is constructed by synthesizing the sinusoidal output by discrete voltage sources, such as storage batteries, solar cell, etc., with electronic switching of the sources at specific time intervals. The switching times are determined for the condition of minimum distortion of the synthesized wave. A 50 W inverter was built and tested to demonstrate this approach.     

正弦波模型化测量方法及应用

本文对应用较多的几种正弦波模型化测量方法进行了综述，它们是曲线拟合法、直方图统计分析法、FFT法和拍频法。较详细地介绍了这几种测量方法的典型用途以及特点，通过比较几种方法的优缺点，讨论了它们应用中的局限性。     

Development of three-phase switch-mode rectifier using single-phase modules

This paper presents a three-phase (3/spl phi/) switch-mode rectifier (SMR) consisting of three 1 /spl phi/ SMRs, two center-tapped autotransformers and three changeover switches. The ac input sides of three modules are /spl Delta/-connected, and their dc output sides are connected in parallel. As any one module fault occurs, the remaining two modules becomes modified T-connected and continuously perform three-phase rectification with good line drawn power quality. When two constituted 1/spl phi/ modules are faulted, the proposed 3/spl phi/ SMR will be operated as 1/spl phi/ SMR. The quantitative and robust voltage regulation controls for the developed SMR are made to consider the effects of changes of system parameters, operating condition, and number of connected modules.     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

Constant Voltage Digital Control of an AC Motor Positioning Servo

A theoretical approach is presented to digitally manipulating the drive frequency of an ac induction motor so as to allow the motor to be used in a closed loop positioning servo. Additionally, the basic power source can be a simple dc power supply such as a battery pack. A hardware demonstration of the loop is discussed which has achieved a convergence accuracy of a 0.3 mrad to a step input.     

电脉冲除冰系统除冰激励的简化与影响因素

首先建立了电脉冲除冰系统的电路模型,求解了有无二极管条件下的理论脉冲电流曲线,通过分析计算电流与实验电流,提出了将正弦半波电流函数用于电磁场分析以简化研究除冰激励的观点,同时求解了不同电流方式下的电磁压力分布,再用结构动力学分析了不同压力载荷下实验铝板的响应位移。其次通过比较铝板中心位移实验值与动力学求解的响应位移值,其有效的吻合程度验证了用正弦半波函数电流简化电脉冲除冰激励分析的可行性。最后,在利用正弦半波电流函数简化分析脉冲激励的基础上,研究了电流大小、电频率、铝板厚度、铝板弹性模量、铝板密度以及铝板长宽比对最大响应位移的影响。研究结果表明,最大响应位移随电流增大而增大,随铝板厚度、弹性模量与密度的增大而减小,且随电频率的改变而改变,但几乎不受铝板长宽比的影响;在研究电频率时得出,可将电频率与系统结构固有频率以1:1的比例设计,此关系式是电脉冲除冰系统电路设计的基础。     

15%SiC_P/8009铝基复合材料热压缩流变应力行为

采用Gleeble-3500热模拟试验机对15%Si CP/8009铝基复合材料在温度为400~550℃和应变速率为0.001~1 s~(-1)条件下的热变形流变行为进行研究。结果表明:流变应力在开始阶段随应变的增加而增大,出现峰值后逐渐趋于平稳;流变应力随温度的升高而降低,随应变速率的增大而升高,呈现出正应变速率敏感性;流变应力行为可以用双曲正弦模型来描述,其热变形激活能为488.3853 k J/mol,应力指数为7.19022。