耐高温苯并恶嗪的合成与表征

为了提高苯并恶嗪的耐高温性能,合成了含醛基的苯并恶嗪中间体.采用溶剂两步法合成含醛基的苯并恶嗪中间体,利用红外光谱和核磁氢谱对其结构进行表征,同时利用DSC对其固化反应过程进行了研究,通过TGA对其耐热性能进行测试.结果表明含醛基的苯并恶嗪中间体在氮气保护下,800℃的残碳率高达65.63%,与普通的苯并恶嗪树脂相比,残碳率提高了20%,耐热指数为221.09℃.综上可知,醛基的引入可以有效地提高苯并恶嗪树脂的耐热性能和热稳定性能.     

芴基取代耐高温聚酰亚胺的合成与性能

合成了同时含有芴基以及醚键的二胺单体,9,9-双(4-胺基苯氧基苯基)芴(BAOFL),并对其进行熔点、红外以及核磁表征。结果表明,该单体具有很高的纯度。分别采用3,3,′4,4′-联苯四甲酸二酐(sBPDA)以及2,3,3,′4′-联苯四甲酸二酐(aBPDA)与BAOFL聚合,通过热亚胺化法以及化学亚胺化法分别制备聚酰亚胺(PI)。研究芴取代基对PI耐热性能、溶解性能以及光学性能的影响。结果表明,引入芴取代基可以显著提高PI树脂在有机溶剂中的溶解性能以及在可见光区良好的透明性。同时,PI具有良好的耐热稳定性,玻璃化转变温度超过280℃,氮气中起始热分解温度超过500℃。     

邻苯二甲腈基联苯型酚醛树脂的制备与性能

以碱为催化剂,通过联苯型酚醛树脂与4-硝基邻苯二甲腈之间的亲核取代反应,制备了邻苯二甲腈基联苯型酚醛树脂(PBN).流变性能测试结果表明,PBN树脂在180 ～ 300℃,黏度＜400 mPa·s,表明该树脂具有优良的加工性能.DSC测试结果表明,PBN树脂的固化温度为280～450℃,固化反应峰值温度为377℃,固化放热约为187 J/g.该树脂表现出优良的耐热性,其储能模量起始下降温度高于450℃,Td5约为529℃,氮气氛围、900℃残碳率约为78％.     

纳米SiO2填充杂萘联苯聚醚酮复合材料的性能研究

采用悬浮液共混法制备了纳米SiO2填充新型含二氮杂萘酮结构聚芳醚酮(PPEK)复合材料,并对其力学性能、摩擦性能和热学性能进行了研究。结果表明：当纳米SiO2含量为1％时,复合材料的综合力学性能最佳;纳米SiO2的加入,使得复合材料的摩擦性能比纯树脂有了明显提高,当纳米SiO2含量达到7％时,摩擦磨损综合性能最好,且在大载荷下纳米SiO2更能有效改善复合材料的摩擦磨损性能。DSC测试表明,7％纳米SiO2填充PPEK的玻璃化转变温度与纯PPEK相当。     

玻璃布增强PPBES/ PPENK 树脂基层压板的研究

将含二氮杂萘酮结构、耐高温可溶解的聚芳醚砜(PPBES) 与聚芳醚腈酮(PPENK) 共混,采用溶
液浸渍法制备了玻璃布增强PPBES/ PPENK 树脂基层压板。讨论了树脂的相容性及树脂配比,研究了共混树
脂含量对PPBES/ PPENK 层压板的室温及150℃弯曲强度、吸水率的影响,对层压板的介电性能、阻燃性能等
进行了测试。结果表明:PPBES 与PPENK 完全相容。当PPBES/ PPENK = 4/6( 质量比),树脂质量分数为
35． 4%时,层压板的综合性能最佳,且150℃的弯曲强度保持率为95. 7%。在1 MHz 下,介电常数为3. 5,tanδ
为0. 0037;在DC 500 V 下,体积电阻率为5. 9×1014Ω·cm;阻燃性能达到V-0 级。     

一种基于酚醛骨架的耐高温RTM树脂

利用双马来酰亚胺树脂改性烯丙基化线型酚醛树脂 (BMAN)制备了可用于RTM成型的耐高温树脂。该树脂在 1 0 0℃下 8h内的粘度小于 1 5 0mPa·s ,适用于RTM成型工艺和模压工艺。且该树脂具有良好的耐高温性能 ,DMA分析表明树脂浇铸体模量曲线拐点温度Tonset在 390℃以上 ,玻璃化温度大于4 0 0℃。石英纤维 /BMAN树脂复合材料也拥有较好的耐高温性能 ,可以在 35 0℃下使用     

耐高温聚苯硫醚复合涂层性能的研究

主要讨论增韧材料对PPS性能的影响和各种填料用量对PPS复合涂层的附着力、抗冲击强度等性能的影响以及PPS复合涂层的耐高温性能。结果表明：增韧树脂PEK－C的加入可提高PPS共混树脂的力学性能；共混树脂中加入5％的石墨、10％TiO2时，可获得综合性能良好的复合涂层。     

耐高温双马树脂体系

研究了803树脂的反应特性、流变特性,MT300/803复合材料的耐热性能和力学性能,并分析了复合材料的微观形貌.结果表明:803树脂具有很高的活性、良好的流动性及工艺性;MT300/803复合材料具有优异的耐高温性能,DMA储能模量转变点约为300℃,T<,d><'5>为396℃,其室温、高温力学性能优异;803树脂与MT300碳纤维界面强度高、匹配性好.综合分析,803树脂及其复合材料具有优异的耐高温性能,可推广应用于航天高性能耐高温结构复合材料领域.     

碳纤维增强耐热环氧树脂复合材料工艺性能研究

研究了一种低黏度耐高温环氧树脂体系的黏温特性及固化反应动力学,考察了该树脂体系的浇注体及其碳纤维复合材料的力学性能,通过热机械分析(DMTA)研究了树脂浇注体及其复合材料的动态热机械性能.结果表明,该树脂体系在室温下黏度为0.3 Pa·s,50℃下适用期在10 h以上,130℃下可以快速固化反应,适合于RTM等快速成型工艺,Tg达到220℃以上,其碳纤维复合材料具有优良的耐高温性能.     

苯酚-淀粉树脂的合成与性能

介绍了以苯酚、淀粉为原料,在硫酸的催化下,经缩聚一步合成一种新型苯酚 淀粉树脂,表征了合成反应机理与树脂结构,探讨了催化剂用量、工艺参数(总反应时间、最高反应温度)、投料比(苯酚 淀粉)对产物的影响,确定了典型的原料配方、合成工艺路线与工艺参数,进行了性能和效益优势分析。结果表明,苯酚 淀粉树脂属于热塑性酚醛树脂,其性能与热塑性苯酚 甲醛树脂相似,特别是具有很好的耐热性,而且经济和环境效益优势明显。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

ν-gap度量及其在飞行控制律评估中的应用

 传统控制律评估方法主要用于单输入单输出（SISO）系统，且对模型参数摄动考虑不够全面,针对这些不足，研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上，给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算，提出ν-gap度量评估控制律的步骤。实例结果表明，该方法不仅克服了上述传统评估方法的缺陷，而且还有根据所求的各摄动影响情况忽略影响小的元素，以减少计算量及可以找到最坏情况下的参数摄动组合等优点。     

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Integrated Entry Guidance for Reusable Launch Vehicle

A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。