Al2O3陶瓷蠕动进给超声磨削加工表面质量的试验研究

为探索利用简单形状砂轮对陶瓷材料进行数控展成型面超声磨削,通过对Al2O3陶瓷进行蠕动进给超声磨削和机械磨削对比试验研究,探索各加工参数对磨削表面质量的影响规律.结果表明:超声振动方向与蠕动进给方向平行时可降低表面粗糙度值,而超声振动方向与蠕动进给方向垂直时则不利于改善加工表面质量;在超声磨削条件下,为了提高加工表面质量,应采取较小的磨削深度、较低的进给速度和适当高的磨削速度以及复合进给磨削方式.结合试验结果理论分析了蠕动进给超声磨削和蠕动进给机械磨削加工机理,并根据试验结果选择磨削参数进行了陶瓷叶片型面超声磨削的可行性试验.     

超声振动磨削C/SiC复合材料的试验研究

采用电镀金刚石砂轮对CVI+PIP综合工艺制备的2.5D正交编织C/SiC陶瓷基复合材料进行了轴向超声振动平面磨削加工试验.通过对超声振动磨削与普通磨削的磨削力、磨削表面三维形貌及粗糙度的分析与测量,对C/SiC复合材料的加工工艺进行了研究.结果表明,磨削过程中材料去除方式以脆性去除为主,碳纤维损伤形式以纤维拉断、剥离...     

旋转超声振动端面磨削CFRP表面质量研究

以多向层铺树脂基碳纤维增强复合材料为研究对象,采用超声振动磨削和普通磨削对其表面加工质量进行了端面磨削试验研究.通过正交试验和单因素试验分析了各工艺参数对工件表面质量的影响规律,并由表面粗糙度及微观形貌进一步分析了磨削机理.试验结果表明:在超声磨削过程中提高主轴转速、减小进给速度,同时采用合适的切削深度和工具粒度,有助于获得高质量的加工表面;超声振动磨削和普通磨削后,工件表面均存在纤维丝断裂、剥离和凹坑等缺陷,超声振动磨削后的加工缺陷出现的程度和概率均较低,表面加工质量较好.     

Al2O3/ZrO2(n)微纳米复合陶瓷超声振动精密磨削表面微观特征试验研究

 基于Al₂O₃/ZrO₂（n）微纳米复合陶瓷的“晶内型”微观结构，应用原子力显微镜(AFM)重点分析了微 纳米复合陶瓷二维超声振动磨削表面微观形貌。结合磨削表面X射线衍射定性分析与定量计算，研究了“晶内型”微纳米复合陶瓷材料超精密振动磨削表面变质层结构。X射线衍射分析表明：二维振动磨削和普通磨削表面均以α-Al₂O₃和四方相ZrO₂为主，存在少量单斜相ZrO₂，磨削表面无非晶相产生；磨削表层和基体之间的过渡层的X射线衍射峰具有半峰宽化现象。AFM分析结果表明：细粒度金刚石砂轮普通磨削和振动磨削表面均无微裂纹和断裂破碎，磨削表面粗糙度是由不同幅值的多种波形叠加的结果；AFM轮廓特征分析表明：二维超声振动磨削表面峰谷较均匀，磨削表面均匀一致性优于普通磨削表面；材料晶化过程中产生的固有缺陷是限制硬脆材料近纳米表面形成的重要因素。     

不同材料超声振动磨削的磨削温度实验研究

本文采用人工热电偶测温方式,对纳米Al2O3陶瓷和普通45#钢进行了普通和超声振动下平面磨削磨削温度的测量.比较了相同磨削参数下超声和普通磨削温度的实验数据.实验结果显示:超声辅助磨削纳米氧化铝陶瓷时陶瓷表面磨削温度比普通磨削时低.但超声辅助磨削45#钢时其磨削温度与普通磨削情况下差别不大.     

纳米ZrO2陶瓷二维超声磨削温度影响因素分析

本文采用人工热电偶法,通过普通磨削和二维超声振动磨削的对比实验,回归分析了磨削深度、砂轮速度、工作台速度等磨削参数对纳米ZrO2陶瓷磨削温度的影响.别外对纳米ZrO2陶瓷这种非线性材料的磨削加工进行有限元仿真,比较实验测量数据与仿真结果,确定仿真分析对实际情况的指导作用.     

DD5镍基单晶高温合金缓进磨削力和温度实验研究

涡轮叶片榫齿缓进磨削过程热力载荷效应对成型表面质量具有重要影响。基于实验研究磨削参数对DD5 单晶高温合金磨削力和温度的影响规律,分析缓进磨削力和温度形成机理,构建 DD5 缓进磨削力、温度与磨削工艺参数的映射模型并进行验证。结果表明：DD5 缓进磨削深度对磨削力和磨削温度的影响最为显著,砂轮线速度次之,工件进给速度对其影响最小;随着砂轮线速度的增大,磨削力降低、磨削温度升高;随着工件进给速度和磨削深度的增大,磨削力和磨削温度均呈升高趋势;满足材料去除速率的前提下提高工件进给速度并降低磨削深度,可以避免 DD5 磨削表面出现较大的磨削热力耦合影响层。     

超声ELID 复合磨削磨削力模型研究

以ELID 电解原理为基础,结合超声振动辅助磨削过程中单颗磨粒的运动学分析,建立了超声 ELID 复合磨削条件下的磨削力数学解析模型,并对模型进行了分析和仿真。对模型的分析表明:超声振动改 变了磨粒的运动轨迹,使同等条件下的未变形切屑厚度减小,砂轮的在线电解修整使磨粒始终处于锋锐状态, 而且影响砂轮的实际切削深度,进而对磨削力产生影响。磨削力随着超声振动频率、振幅、电解电压、脉冲比、 电解液电阻率的增大而减小;随着切削深度、工件速度的增大而增大。     

碳纤维陶瓷基复合材料的磨削加工研究进展

综述了磨削参数、纤维方向、不同加工方式以及其他因素对磨削力和表面质量的影响规律;总结了不同加工方式下的碳纤维陶瓷基复合材料的磨削机理;展望了碳纤维陶瓷基复合材料磨削加工的研究方向。     

颗粒增强钛基复材缓进深切磨削加工研究

颗粒增强钛基复合材料(PTMCs)属于典型的难加工材料,在航空航天领域具有广阔应用前景.本文开展了PTMCs材料的缓进深切磨削研究,揭示了磨削用量和磨削方式(顺磨与逆磨)对磨削力与磨削温度的影响规律,同时利用有限元法分析了磨削温度场特征和材料去除机理.研究发现,缓进深切磨削PTMCs时,磨削力随工件进给速度和切深增加而增加,顺磨时的磨削力比逆磨大10％～20％,而顺磨的磨削温度要比逆磨约低10％.由于逆磨和顺磨工件的温度分布不同,当切深大于0.6mm、工件进给速度大于400mm/min时,顺磨比逆磨更易发生烧伤.在此基础上,提出了顺磨与逆磨条件下磨削温度场仿真计算的不同热源模型与边界条件,分别获得了两种磨削方式的温度分布特征,有限元仿真结果与试验结果相符.颗粒增强钛基复材磨削表面典型加工缺陷是表面涂覆和硬脆增强相破碎和拔出导致的孔洞,单颗磨粒切厚对硬脆增强相的去除行为有显著的影响.     

断续 CBN 砂轮缓进给磨削 K417 航空叶片材料的研究

 全面比较了用Al2O3和CBN磨削K417铸造高温合金时的磨削效果，指出：Al2O3不适于高效磨削K417之类的航空难加工材料，而CBN是实现该材料高效深切磨削的有效工具。通过大量实验，验证了断续CBN砂轮缓进给磨削K417时的技术优势，解决了树脂结合剂应用于断续磨削时所遇到的新问题。分析显示出该技术具有很好的应用前景和极大的推广价值。     

Influences of Mechanical Vibration on Rapidly Solidified Al_2O_3/YSZ Ceramics Prepared by Combustion Synthesis

Al2O3/YSZ composite ceramics was fabricated with combustion synthesis technology, and the influences of mechanical vibration on its microstructures and properties were investigated. It is found that under the mechanical vibration of ever-increasing frequency, increasing combustion temperature, accelerating ceramics/metal liquid-liquid separation and quickening ceramic solidification could not only reduce the average diameter and the size distribution of aligned ZrO2 nano-micron fibers in rod-shaped Al2O3 matrix grains, but also make the randomly-oriented rod-shaped grains finer and increase their aspect ratios. As a result, a remarkable increase in flexural strength and fracture toughness of the ceramics can be observed.     

Influences of Mechanical Vibration on Rapidly Solidified Al2O3/YSZ Ceramics Prepared by Combustion Synthesis

Al2O3/YSZ composite ceramics was fabricated with combustion synthesis technology, and the influences of mechanical vibration on its microstructures and properties were investigated. It is found that under the mechanical vibration of ever-increasing frequency, increasing combustion temperature, accelerating ceramics/metal liquid-liquid separation and quickening ceramic solidification could not only reduce the average diameter and the size distribution of aligned ZrO2 nano-micron fibers in rod-shaped Al2O3 matrix grains, but also make the randomly-oriented rod-shaped grains finer and increase their aspect ratios. As a result, a remarkable increase in flexural strength and fracture toughness of the ceramics can be observed.     

Grindability and Surface Integrity of Cast Nickel-based Superalloy in Creep Feed Grinding with Brazed CBN Abrasive Wheels

The technique of creep feed grinding is most suitable for geometrical shaping, and therefore has been expected to improve effectively material removal rate and surface quality of components with complex profile. This article studies experimentally the effects of process parameters (i.e. wheel speed, workpiece speed and depth of cut) on the grindability and surface integrity of cast nickel-based superalloys, i.e. K424, during creep feed grinding with brazed cubic boron nitride (CBN) abrasive wheels. Some important factors, such as grinding force and temperature, specific grinding energy, size stability, surface topography, microhardness and microstructure alteration of the sub-surface, residual stresses, are investigated in detail. The results show that during creep feed grinding with brazed CBN wheels, low grinding temperature at about 100 °C is obtained though the specific grinding energy of nickel-based superalloys is high up to 200-300 J/mm³. A combination of wheel speed 22.5 m/s, workpiece speed 0.1 m/min, depth of cut 0.2 mm accomplishes the straight grooves with the expected dimensional accuracy. Moreover, the compressive residual stresses are formed in the burn-free and crack-free ground surface.     

Thermomechanical coupling effect on characteristics of oxide film during ultrasonic vibration-assisted ELID grinding ZTA ceramics

Ultrasonic vibration-assisted ELID (UVA-ELID) grinding is utilized as a novel and highly efficient processing method for hard and brittle materials such as ceramics. In this study, the UVA-ELID grinding ZTA ceramics is employed to investigate the influence of thermomechanical loading on the characteristics of oxide film. Based on the fracture mechanics of material, the model of internal stress for oxide film damage is proposed. The thermomechanical loading is composed of mechanical force and the thermal stress generating from grinding temperature. The theoretical model is established for the mechanical force, thermal stress and internal stress respectively. Then the finite element analysis method is used to simulate the theoretical model. The mechanical force and grinding temperature is measured during the actual grinding test. During the grinding process, the effect of grinding wheel speed and grinding depth on the thermomechanical force and the characteristics of oxide film is analyzed. Compared with the conventional ELID (C-ELID) grinding, the mechanical force decreased by 25.6% and 22.4% with the increase of grinding wheel speed and grinding depth respectively, and the grinding temperature declined by 10.7% and 12.8% during the UVA-ELID grinding. The thermal stress in the latter decreased by 16.3% and 20.8% respectively, and internal stress reduced by 12.3% and 15.6%. It was experimentally found that the topographies of oxide layer on the surface of the wheel and the machined surface in the latter was better than that in the former. The results indicate that the action of ultrasonic vibration establish a significant effect on the processing. Subsequently, it should be well considered for future reference when processing the ZTA ceramics.     

缓磨烧伤过程的计算机仿真研究

在关于缓磨时的磨削热 ,接触弧区换热过程以及工件表层非稳态温度场的深入研究的基础上 ,构造了一可用于计算缓磨烧伤前后工件表层温度场畸变历程的数学模型 ,并据此完成了关于缓磨烧伤过程的计算机仿真研究 ,仿真结果与实际吻合良好 ,它率先阐明了缓磨烧伤的热机理并且证明了缓磨烧伤是一具有明显前兆特征的典型渐变过程     

Developing a novel radial ultrasonic vibration-assisted grinding device and evaluating its performance in machining PTMCs

Particle-reinforcing titanium matrix composites(PTMCs) exhibit the sharp raising applications in modern industries owing to its extraordinary physical and mechanical properties. However, the poor grindability and unstable grinding processes due to the existence of TiC particles and TiB short fibres inside PTMCs, leading to the sudden grinding burn and low material removal rate.In this work, a novel radial ultrasonic vibration-assisted grinding(RUVAG) device with a special cross structure was dev...     

Feasibility study of creep feed grinding of 300M steel with zirconium corundum wheel

The ultrahigh strength 300M steel has been commonly used in the manufacture of aircraft landing gear and rotor shaft parts due to its excellent mechanical properties. Creep feed grinding is one of the essential operations during the whole component manufacturing processes. In this work, the feasibility of creep feed grinding of 300M steel by using the hard zirconium corundum wheel was theoretically and experimentally evaluated. A variety of responses including grinding forces, temperature fields...