Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Suitability of pulse train control technique for BIFRED converter

Pulse Train/spl trade/ control scheme is presented and applied to a boost integrated flyback rectifier/energy storage dc-dc (BIFRED) converter operating in discontinuous conduction mode (DCM), which avoids the light-load high-voltage stress problem. In contrast to the conventional control techniques, the principal idea of Pulse Train technique is to regulate the output voltage using a series of high and low energy pulses generated by the current of the inductor. The applicability of the proposed technique to both the input and magnetizing inductances of BIFRED converter is investigated. Analysis of BIFRED converter operating in DCM as well as the output voltage ripple estimation is given. Experimental results on a prototype converter are also presented.     

Improved ZCS-PWM commutation cell for IGBTs application

An improved zero-current-switching pulsewidth-modulated (ZCS-PWM) commutation cell is presented, which is suitable for high-power applications using insulated gate bipolar transistors (IGBTs) as the power switches. It provides ZCS operation for active switches and zero-voltage-switching (ZVS) operation for passive switches. Besides operating at constant frequency and reducing commutation losses, the proposed ZCS-PWM switch cell has no additional current stress and conduction loss in the main switch. To demonstrate the feasibility of the proposed ZCS-PWM commutation cell, it was applied to a boost converter. Operating principle, theoretical analysis, design guidelines, and a design example are described and verified by experiment results obtained from a prototype rated 1 kW and operating at 40 kHz. The PWM switch model and state-space averaging approach is also used to estimate and examine the steady-state and dynamic character of ZCS-PWM boost converter system. Finally, the application of the proposed soft-switching technique in the dc-dc nonisolated converters is presented.     

A new zero-voltage switching DC/DC boost converter

A pulsewidth-modulated (PWM) zero-voltage-switching quasi-resonant boost converter operating at constant switching frequency is presented. In contrast to the frequency-modulated (FM) zero-voltage-switching quasi-resonant boost converter, this converter possesses better controllability and higher operating performance, and overcomes the instability caused by the parasitic oscillation. The principle of operation and performance of the converter are presented. Its two-dimensional state trajectories and steady-state characteristic curves are derived which are useful for the converter design. Both the SPICE simulation and experimental result agree with the theoretical prediction     

Full bridge ZCS PWM converter for high-voltage high-powerapplications

This paper presents a comprehensive study of a full bridge (FB) zero-current switched (ZCS) PWM converter which is suitable for high-voltage and high-power DC application that achieves ZCS for all active switches, and zero-voltage-switched (ZVS) operation for all diodes on the high voltage side. The given converter utilizes component parasitic parameters, particularly for the high-voltage transformer, and employs fixed-frequency phase-shift control to implement soft-switching commutations. Detailed steady state analysis of the converter power stage is presented for the first time and the major features of the converter's power stage are discussed. Small-signal characteristics are also presented and accompanied by a discussion of the controller design and implementation. A design example is also presented based on the steady state analysis and is validated by simulation. Theoretical and simulated results are in good agreement     

Efficient power supply for the microwave electrothermal thruster(MET)

A resonant switch-mode power supply for the microwave electrothermal thruster (MET) is presented in this paper. The converter is operated with soft-switching at high frequency and exhibits a high efficiency. The soft switching technique used in this converter and the current-source inductor at the input minimize the EMI noise. Electric isolation between input and output is achieved with a center-tap transformer, whose magnetizing inductance is used as the resonant inductance of its resonant tank. The resulting high power density and increased reliability of the converter make it very suitable for aerospace applications. Simulation and experimental results of a 28 V/4.5 kV example are also presented     

Flyback Converter Output Voltage Stabilization

The expression of the flyback converter output voltage (output power) is derived as a function of the supply voltage, load resistance, transformer ratios, transistor current gain, and base-circuit resistor value. Switching period and duty cycle are also calculated. A converter circuit is designed having stabilized output voltage, with respect to supply voltage, at constant load. The transistor base current is controlled by the supply voltage, via a nonlinear circuit. This feedforward circuit approximates with logarithmic characteristics the ideal hyperbolic dependence of the transistor base current as a function of the supply voltage. The converter has high performance and low cost. A cheaper circuit variant is presented, in which the high-voltage control transistor was eliminated.     

Design optimization for asymmetrical ZVS-PWM zeta converter

In this paper, a new soft-switching Zeta converter with an asymmetrical pulsewidth modulation (PWM) control is proposed. The proposed Zeta converter has the features of constant frequency operation, zero voltage switching (ZVS), and low voltage stress on the active switches. Moreover, it can achieve high power density, high efficiency, low switching loss, and low component count, which make converter operation at low to medium power level feasible. Operational principle of the Zeta converter is presented in detail, and a specific example is designed and implemented to verify its feasibility.     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

Novel single-switch converter with power factor correction

A new single-stage single-switch power factor correction converter with output electrical isolation is presented. The configuration of this converter is achieved by combining a flyback circuit and a forward circuit in one power stage. The principle of operation and steady-state analysis of the proposed topology is given. Based on its steady-state operation constraints, a design procedure along with a specific design example is reported. To verify the theoretical analysis of the proposed converter, a design example is given with its PSPICE simulation and experimental results     

General rules for signal flow graph modeling and analysis of dc-dc converters

Signal flow graph (SFG) nonlinear modeling approach is well known for modeling dc-dc converters. However, all possible SFGs of a given dc-dc converter system will not yield the generalized graph. A systematic procedure and guidelines for developing unified flow graph models of the dc-dc boost converters, from which complete behavior can be determined is presented. Usefulness of the proposed method is demonstrated through examples. As an illustration a 2-cell cascade boost and interleaved boost converter systems are taken as examples. Derivation of large, small-signal and steady-state models from generalized flow graph is also demonstrated. Large-signal model is developed and programmed in TUTSIM simulator. Large-signal, responses against supply and load disturbances are obtained. Experimental observations are provided to validate the proposed algorithm.     

ZVT boost converter using a ZCS auxiliary circuit

A soft switching boost converter with zero-voltage transition (ZVT) main switch using zero-current switching (ZCS) auxiliary switch is proposed. Operating intervals of the converter are presented and analyzed. Design considerations are discussed. A design example with experimental results obtained from a 600 W, 100 kHz, 380 V output, power factor corrected, ac-to-dc, boost converter using insulated gate bipolar transistors (IGBTs) is presented, Results show that the main switch maintains ZVT while the auxiliary switch retains ZCS for the complete specified line and load conditions     

一种基于反激变换器新型掉电保持电路的设计与分析

本文通过对民用机载设备小功率电源的需求分析和标准解析,总结了传统设备内单独设计掉电保持 电路的优缺点,设计一种基于反激变换器的掉电保持电路,通过分析与测试,验证了该方案的有效性,满足机 载设备的应用场景。     

Computer Simulations of Optimum Boost and Buck-Boost Converters

The development of mathematical models suitable for minimum weight boost and buck-boost converter designs are presented. The facility of an augumented Lagrangian (ALAG) multiplier-based nonlinear programming technique is demonstrated for minimum weight design optimizations of boost and buck-boost power converters. ALAG-based computer simulation results for those two minimum weight designs are discussed. Certain important features of ALAG are presented in the framework of a comprehensive design example for boost and buck-boost power converter design optimization. The study provides refreshing design insight of power converters and presents such information as weight and loss profiles of various semiconductor components and magnetics as a function of the switching frequency.     

小型航空活塞发动机点火系统优化设计

针对微型无人机用小功率航空活塞发动机电容放电点火系统快速高效充电进行了优化设计与试验研究.分析了传统充电升压变换采用恒频脉宽调制PWM(pulse width modulation)方式的缺点,提出了一种开关频率可变、输出电压检测无需电阻分压实现的充电方式,推导给出了关断时间和充电时间的计算公式,设计实现了该充电电路并进行了试验.结果表明:该充电方式充电时间短,效率高;充电时间估算方法准确可靠,误差小,计算量少.      

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Modeling of a new ZVS bi-directional dc-dc converter

A dual half-bridge (DHB) bidirectional dc-dc converter is a new proposed topology that has the advantages of decreased number of devices, soft-switching implementation, low cost, and high efficiency. Typical applications of this converter are the auxiliary power supply in fuel cell vehicles and battery charging and discharging systems where the power density, cost, weight, and reliability are critical factors. A switching-frequency-dependent state-space averaged model of the converter is developed here for either direction of power flow. This averaged model can be used to derive the steady-state characteristics and small signal dynamics of the proposed topology. It also provides a fast simulation tool to investigate the transient response of the converter. The simulated waveforms of the mathematical model are compared with the detailed circuit simulation to verify the accuracy of the modeling.     

Power factor correction circuits with robust current control technique

A dynamically robust current control method to synthesize a sinusoidal input current for AC-to-DC converters with boost type topology is presented. Under this control strategy, the inductor current and the diode current of the boost converter are fed back and combined in a special way which makes the input current of the AC-to-DC converter stable and robust. The input current is solely determined by the reference current. When the reference current signal is derived from the sinusoidal input voltage, the input current is sinusoidal and in phase with the input voltage. Theoretical analysis is first provided. Small signal analysis shows that the current loop is inherently stable and has a fast dynamic response. Large signal analysis reveals that the control system is not affected by large disturbances in supply voltage or output load. Computer simulations have been carried out and experimental prototype models have been built to verify the analysis and demonstrate the feasibility of the control strategy. A power factor of 0.998 and a total harmonic distortion (THD) of 3.18% are measured.     

Robust Hybrid Control for Ballistic Missile Longitudinal Autopilot

This paper investigates the boost phase’s longitudinal autopilot of a ballistic missile equipped with thrust vector control. The existing longitudinal autopilot employs time-invariant passive resistor-inductor-capacitor (RLC) network compensator as a control strategy, which does not take into account the time-varying missile dynamics. This may cause the closed-loop system instability in the presence of large disturbance and dynamics uncertainty. Therefore, the existing controller should be redesigned to achieve more stable vehicle response. In this paper, based on gain-scheduling adaptive control strategy, two different types of optimal controllers are proposed. The first controller is gain-scheduled optimal tuning-proportional-integral-derivative (PID) with actuator constraints, which supplies better response but requires a priori knowledge of the system dynamics. Moreover, the controller has oscillatory response in the presence of dynamic uncertainty. Taking this into account, gain-scheduled optimal linear quadratic (LQ) in conjunction with optimal tuning-compensator offers the greatest scope for controller improvement in the presence of dynamic uncertainty and large disturbance. The latter controller is tested through various scenarios for the validated nonlinear dynamic flight model of the real ballistic missile system with autopilot exposed to external disturbances.     

浅析弹道导弹突防导弹防御系统

根据美国导弹防御系统（NMD）的防御特点，对弹道导弹突防的战略技术进行简要评估，分析了弹道导弹突防采用不同弹头、释放有源或无源干扰物、隐身和反探测、助推段机动及旋转导弹等技术。