首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
为了研究毛细管放电型脉冲等离子体推力器输出特性,借助电学诊断手段展开实验研究,获得了推力器典型放电波形,系统研究了不同毛细管内径和施加电压对等离子体等效阻抗、沉积能量效率的影响规律。利用微冲量测量台架,测试了不同参数下毛细管推力器输出元冲量,并通过计算获得了推力器比冲、总体效率的变化规律。实验结果表明,当毛细管内径不断增大时,能量沉积效率不断下降,元冲量下降,比冲降低。主电容电压增大时,放电能量不断增大,能量沉积效率降低,元冲量和单次等效烧蚀质量不断增大,但推力器比冲和总体效率均先增加并趋于稳定。当毛细管腔体长度为16mm,内径3mm,主电容2.5μF,充电电压为2kV时,输出元冲量350.79±7.50μN?s,比冲531s,总体效率可达18.3%。  相似文献   

2.
脉冲等离子体推力器(PPT)的性能受多方面因素的影响,包括放电参数以及推力器本体结构等。通过对脉冲等离子体推力器的工作原理和物理学模型的分析,研究了PPT的效率、比冲、推力、元冲量、推功比等性能参数与电极结构、电气参数的关系,并设计了实验,对效率、比冲、元冲量等与放电能量、电极间距的关系进行了验证。结果表明,效率、比冲、元冲量均随放电能量的提高而增大,元冲量在电极间距为50 mm时大于间距为30 mm、40 mm时的值。根据实验结果,提出了设计高性能PPT的一些优化条件,对PPT的设计有参考意义。  相似文献   

3.
毛细管型脉冲等离子体推力器采用固态工质,电热加速机制,结构简单可靠,是一种具有应用价值的微纳卫星低功率电推进系统。本文建立电学和光学联合诊断系统,对毛细管脉冲等离子体推力器等离子体羽流演变过程进行了研究。由于放电电流振荡,推力器等离子体羽流存在二次建立过程。初始阶段等离子体羽流中主要包含带电粒子组分,二次建立阶段等离子体羽流主要包含中性成分。利用光电二极管阵列和窄带滤光片建立了飞行时间法,获得了不同放电电压、腔体内径和腔体长度下等离子体羽流分团的等效速度演变特性。结果表明,电热加速机制能够使带电组分和中性成分获得较为良好的加速效果(>10km/s)。在一定放电能量下,放电腔体长度小于25mm有利于获得较优性能参数。等离子体羽流等效速度结果能够较为准确地反映推力器输出比冲和效率参数变化规律,可作为推力器输出参数便捷有效的评估手段。  相似文献   

4.
脉冲等离子体推力器烧蚀建模与仿真   总被引:1,自引:1,他引:0  
为了深入地揭示平板型脉冲等离子体推力器(PPT)工作机理,通过对PPT在放电过程中的欧姆加热能量分配分析,建立了基于能量守恒原理的改进烧蚀模型,并对磁流体动力学方程中的能量方程进行了修正。结合LES-6对PPT工作过程进行了一维磁流体动力学数值仿真,获得了PPT的速度分布、放电烧蚀质量和元冲量等参数的变化过程。仿真结果表明,改进模型能正确地反映脉冲等离子体推力器工作过程,仿真得到的出口速度、元冲量与实验值吻合较好,而放电烧蚀质量则相对误差较大;当电容容量变化时,元冲量随放电能量增大呈近似的线性增长关系,放电烧蚀质量随放电能量的增大单调增加且呈非线性关系。  相似文献   

5.
耿金越  秦宇  龙军  刘旭辉  沈岩 《推进技术》2020,41(1):157-163
采用试验方法研究了微阴极电弧推力器中峰值放电电流及外加磁场对其推力、比冲、寿命的影响规律。试验结果表明:峰值放电电流增加,阴极烧蚀量增加,元冲量增大;相比于较低的峰值放电电流(10A),更高的峰值放电电流(40A)可延长推力器的工作寿命;外加磁场增强,推力器喷射等离子体轴向速度增大,比冲增加。  相似文献   

6.
磁场位形和通道尺度会改变霍尔推力器等离子体放电过程,影响推力器的宏观放电特性。为分析磁场和通道宽度对推力器放电性能的影响规律,本文针对霍尔推力器轴对称通道结构和放电物理过程建立2D3V物理模型,采用粒子模拟方法研究了霍尔推力器磁零点磁场位形不同通道宽度的电势、粒子数密度、电子温度、电离速率、比冲及推功比的变化规律,结果表明:在具有磁零点磁场位形下,随着通道宽度增加,通道出口处电势降增加,加速区缩短,离子径向速度减少,壁面腐蚀降低;当磁零点位置在内壁面,推力器通道宽度由14 mm增加到16 mm时,推力器比冲和推功比增大,推力器放电效率提高;当磁零点位置在通道中轴线或外壁面,且通道宽度大于14 mm时,推力器比冲增大,推功比减小,推力器效率下降。  相似文献   

7.
运用磁流体动力学的方法,对脉冲等离子体推力器推力室工作过程开展三维双温MHD数值仿真,并开展对推力室的工作机理的分析研究。通过该模型计算得到的推进剂烧蚀质量和元冲量与实验结果相符,同时针对不同初始电压、电容以及两种特征波形的情况进行评估,为推力器的放电波形设计提供指导依据。结果显示在推力器波形设计的初期,是采用电流高变化率低能量水平,还是采用电流低变化率高能量水平,需要结合实际,进行优化评估。  相似文献   

8.
李倩  洪延姬  曹正蕊  黄辉 《推进技术》2009,30(6):762-765,768
在9种等离子体击穿温度下,数值模拟了二次反射式聚焦系统聚焦情况下激光推力器内流场的演化过程,得到了不同击穿温度对应的能量沉积率、推力峰值、冲量和冲量耦合系数,能量沉积率和推进性能参数在某个等离子体击穿温度值处发生突变。根据空气对激光的逆韧致吸收系数公式,计算了CO2激光辐照下不同等离子体击穿温度对应的空气辐射自由程,发现当等离子体击穿温度为14000K时,辐射自由程为1.4mm,与计算网格的典型尺寸相当,此时入射激光能量在一个网格内以一定效率被吸收,由此确定了基于逆韧致吸收的激光等离子体的击穿温度。  相似文献   

9.
田立成  郭宁  龙建飞  孙小菁  高俊 《推进技术》2014,35(9):1283-1289
为了研究兰州空间技术物理研究所口径为100mm的LHT-100霍尔推力器宽功率范围工作性能,从实验的角度研究了放电电压100~400V、放电功率500~1800W时LHT-100霍尔推力器的工作性能。实验结果表明,LHT-100霍尔推力器可以在较宽功率范围内正常工作,放电特性和推力性能稳定,推力变化范围为30~95mN,比冲变化范围为600~1950s,推力效率变化范围为18%~53%,功率推力比变化范围为14.3~18.4W/mN。  相似文献   

10.
为了研究5kW离子推力器功率宽范围工作能力,采用试验的方法得到阳极电流和屏栅电压与其性能的影响关系。研究结果表明:离子束流随阳极电流增大呈线性增大。当屏栅电压增加时,推力器离子束流先增加然后趋于稳定,加速栅电流单调减小。推力随功率增大呈线性增长,比冲随功率的增大呈非线性增长,在功率308W~4813W下实现了推力12mN~184mN,比冲1817s~3538s, 效率34%~67%的宽范围调节。同时推力器效率随功率增大逐渐增大,并在2902W时存在明显拐点,在实际在轨应用中要根据任务需求确定最佳工作区间提高推力器性能和效率。  相似文献   

11.
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.   相似文献   

12.
Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.  相似文献   

13.
14.
Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.  相似文献   

15.
The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).  相似文献   

16.
超声速燃烧数值模拟中的湍流与化学反应相互作用模型   总被引:1,自引:0,他引:1  
杨越  游加平  孙明波 《航空学报》2015,36(1):261-273
高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。  相似文献   

17.
适于低轨卫星IP网络的单核共享树组播算法(英文)   总被引:1,自引:0,他引:1  
为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。  相似文献   

18.
Jet Vectoring Control Using a Novel Synthetic Jet Actuator   总被引:3,自引:1,他引:2  
A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.  相似文献   

19.
The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.  相似文献   

20.
A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号