OVERSEAS BRIEFS(July1-31)

Early in July Raytheon deliveredthe first Premier I corporate jet.Early in July The 57th AnnualConference of IATA was closed in Madrid,Spain.July 2 EADS and Rosaviakosmosannounced the two sides had signed anEURO1.2 billion agreement.July 4 A Tu-154 plane of a Russianairlines crashed, killing all on board, including 133 passengers and 10 crew members.Early in July The British LiverpoolAirport is going to change its name toLiverpool John Lenon Airport next year inmemory of John Le…     

Aerodynamic Interactions Between Contralateral Wings and Between Wings and Body of a Model Insect at Hovering and Small Speed Motions

In this paper, we study the aerodynamic interactions between the contralateral wings and between the body and wings of a model insect, when the insect is hovering and has various translational and rotational motions, using the method numerically solving the Navier-Stokes equations over moving overset grids. The aerodynamic interactional effects are identified by compar-ing the results of a complete model insect, the corresponding wing pair, single wing and body without the wings. Horizontal, vertical and lateral translations and roll, pitch and yaw rotations at small speeds are considered. The results indicate that for the motions considered, both the interaction between the contralateral wings and the interaction between the body and wings are weak. The changes in the forces and moments of a wing due to the contralateral wing interaction, of the wings due to the pres-ence of the body, and of the body due to the presence of the wings are generally less than 4.5%. Results show that aerodynamic forces of wings and body can be measured or computed separately in the analysis of flight stability and control of hovering in-sects.     

Stability analysis of an aeroelastic system with friction

In this paper, harmonic balance method, exact formulation and numerical simulation method are adopted to study the effects of different friction stiffness on the stability of 1.5 degrees of freedom aeroelastic system. On this basis, the expressions of input energy and dissipated energy are deduced, and the energy method is used to reveal the mechanisms of the stable boundary and unstable boundary existing in the system and the effects of different friction stiffness on the stability of the system. Studies have shown that the stability region and the critical aerodynamic damping ratio of the system rise with the increase of the friction stiffness, while the friction stiffness has little effect on the stability boundary. In the analysis of the stability of system, the results of harmonic balance method, exact formulation and Newmark of numerical simulation method are in good agreement. Compared with exact formulation and numerical simulation method, the concept and conclusion of harmonic balance method are simple in the system stability analysis.     

Experimental Investigation of the Effects of Various Plasma Actuator Configurations on Lift and Drag Coefficients of a Circular Cylinder Including the Effects of Electrodes

In this paper, the effects of the existence of plasma actuator electrodes and also various configurations of the actuator for controlling the flow field around a circular cylinder are experimentally investigated. The cylinder is made of PVC (Polyvinyl Chloride) and considered as a dielectric barrier. Two electrodes are flush-mounted on the surface of the cylinder and are connected to a DC high voltage power supply for generation of electrical discharge. Pressure distribution results show that the existence of the electrodes and also the plasma are able to change the pressure distribution around the cylinder and consequently the lift and drag coefficients. It is found that the effect of the existence of the electrodes is comparable with the effect of plasma actuator in controlling the flow field around the cylinder and this effect is not reported by other researchers. Eventually it is concluded that the existence of the electrodes or any extra objects on the cylinder and also the existence of the plasma are capable of changing the flow field structure around the cylinder so that the behavior of the lift and drag coefficients of the cylinder will be changed significantly.     

Electromagnetism and Absorptivity of the Modified Micro-coiled Chiral Carbon Fibers

Micro-coiled chiral carbon fibers are modified by nano-Ni. X-ray diffraction （XRD） and scanning electron microscopy （SEM） are used to compare the composition and morphology of the unmodified and the modified fibers. The results show that electromagnetism parameters of the modified are different from those of the unmodified. After modification by nano-Ni, the micro-coiled chiral carbon fibers have decreased permittivity and electrical loss. The permeability and magnetic loss of the modified carbon fibers become larger than those of the unmodified ones. Moreover, the modification of unmodified chiral carbon fibers into the modified is much like changing hollow electric windings into those with magnetic cores inside. The modifier intensifies the cross polarization of the chiral carbon fibers and makes the permittivity and the permeability get closer to each other which improves the matching performance and enhances absorbability of coatings. In the range of 6-18 GHz, the reflectivity of the coating is 6-8dB and the bandwidth is 12 GHz. The area density of the coating is below 3 kg/m^2.     

Combined and interactive effects of interference fit and preloads on composite joints

The combined and interactive effects of the bolt-hole fit conditions and the preloads of the fasteners on the load carrying capacity of single-lap composite-to-titanium bolted joints have been investigated both experimentally and numerically. Quasi-static tests of the hybrid joints with different fit conditions are implemented, and a three dimensional finite element progressive failure analysis model is proposed to predict the influences of the bolt-hole fit conditions and fastener＇s pre- loads on the mechanical behaviors of the joints. Based on the experimental validated simulation method, a multi-factor, mixed levels orthogonal design table and the analysis of variance method are used to arrange the simulation conditions and to further study the interactive effects of preloads and fit conditions. Through the analysis of the results, for the researched double bolt, single-lap composite-titanium joints, it is found that： the effects of both the interference fit and the preloads change from positive into negative mode with the increase of the interference fit values or preload values; appropriate bolt-hole fit conditions and preloads can improve the bolt-hole contact conditions of the loaded joints, and then retard the fiber failures around the fastener holes, and increase the load carrying capacity of the joints eventually; the interactive effect of the bolt-hole interference fit conditions and preloads cannot be ignored and the parameters need to be considered together and synthetically as the joints are being optimized.     

Numerical study of aerodynamic characteristics of FSW aircraft with different wing positions under supersonic condition

This paper investigates the influence of forward-swept wing(FSW) positions on the aerodynamic characteristics of aircraft under supersonic condition(Ma = 1.5). The numerical method based on Reynolds-averaged Navier–Stokes(RANS) equations, Spalart–Allmaras(S–A) turbulence model and implicit algorithm is utilized to simulate the flow field of the aircraft. The aerodynamic parameters and flow field structures of the horizontal tail and the whole aircraft are presented. The results demonstrate that the spanwise flow of FSW flows from the wingtip to the wing root, generating an upper wing surface vortex and a trailing edge vortex nearby the wing root.The vortexes generated by FSW have a strong downwash effect on the tail. The lower the vertical position of FSW, the stronger the downwash effect on tail. Therefore, the effective angle of attack of tail becomes smaller. In addition, the lift coefficient, drag coefficient and lift–drag ratio of tail decrease, and the center of pressure of tail moves backward gradually. For the whole aircraft,the lower the vertical position of FSW, the smaller lift, drag and center of pressure coefficients of aircraft. The closer the FSW moves towards tail, the bigger pitching moment and center of pressure coefficients of the whole aircraft, but the lift and drag characteristics of the horizontal tail and the whole aircraft are basically unchanged. The results have potential application for the design of new concept aircraft.     

Numerical Investigation of Flow Separation Control on a Highly Loaded Compressor Cascade by Plasma Aerodynamic Actuation

To discover the characteristic of separated flows and mechanism of plasma flow control on a highly loaded compressor cascade, numerical investigation is conducted. The simulation method is validated by oil flow visualization and pressure distribution. The loss coefficients, streamline patterns, and topology structure as well as vortex structure are analyzed. Results show that the numbers of singular points increase and three pairs of additional singular points of topology structure on solid surface generate with the increase of angle of attack, and the total pressure loss increases greatly. There are several principal vortices inside the cascade passage. The pressure side leg of horse-shoe vortex coexists within a specific region together with passage vortex, but finally merges into the latter. Corner vortex exists independently and does not evolve from the suction side leg of horse-shoe vortex. One pair of radial coupling-vortex exists near blade trailing edge and becomes the main part of backflow on the suction surface. Passage vortex interacts with the concentrated shedding vortex and they evolve into a large-scale vortex rotating in the direction opposite to passage vortex. The singular points and separation lines represent the basic separation feature of cascade passage. Plasma actuation has better effect at low freestream velocity, and the relative reductions of pitch-averaged total pressure loss coefficient with different actuation layouts of five and two pairs of electrodes are up to 30.8% and 26.7% while the angle of attack is 2°. Plasma actuation changes the local topology structure, but does not change the number relation of singular points. One pair of additional singular point of topology structure generates with plasma actuation and one more reattachment line appears, both of which break the separation line on the suction surface.     

机翼颤振的区间有限元分析(英文)

The influences of uncertainties in structural parameters on the flutter speed of wing are studied. On the basis of the deterministic flutter analysis model of wing, the uncertainties in structural parameters are considered and described by interval numbers. By virtue of first-order Taylor series expansion, the lower and upper bound curves of the transient decay rate coefficient versus wind velocity are given. So the interval estimation of the flutter critical wind speed of wing can be obtained, which is more reasonable than the point esti- mation obtained by the deterministic flutter analysis and provides the basis for the further non-probabilistic interval reliability analysis of wing flutter. The flow chart for interval fmite element model of flutter analysis of wing is given. The proposed interval finite element model and the stochastic finite element model for wing flutter analysis are compared by the examples of a three degrees of freedom airfoil and fuselage and a 15° sweptback wing, and the results have shown the effectiveness and feasibility of the presented model. The prominent advantage of the proposed interval finite element model is that only the bounds of uncertain parameters are required, and the probabilistic distribution densities or other statistical characteristics are not needed.     

Adaptive sliding mode control of the A-axis used for blisk manufacturing

As a key assembly in the 5-axis CNC machine tools, positioning precision of the A-axis directly affects the machining accuracy and surface quality of the parts. First of all, mechanical structure and control system of the A-axis are designed. Then, considering the influence of nonlin- ear friction, backlash, unmodeled dynamics, uncertain cutting force and other external disturbance on the control precision of the A-axis, an adaptive sliding mode control （ASMC） based on extended state observer （ESO） is proposed. ESO is employed to estimate the state variables of the unknown system and an adaptive law is adopted to compensate for the input dead-zone caused by friction, backlash and other nonlinear characteristics. Finally, stability of the closed-loop system is guaran- teed by the Lyapunov theory. Positioning experiments illustrate the perfect estimation of ESO and the stronger anti-interference and robustness of ASMC, which can improve the control precision of the A-axis by about 40 times. Processing experiments show that the ASMC can reduce the waviness, averaKe error and roughness of the nrocessed surface by 35.63%, 31.31% and 30.35%, respectively.     

Multi-body dynamic system simulation of carrier-based aircraft ski-jump takeoff

The flight safety is threatened by the special flight conditions and the low speed of carrier-based aircraft ski-jump takeoff. The aircraft carrier motion, aircraft dynamics, landing gears and wind field of sea state are comprehensively considered to dispose this multidiscipline intersection problem. According to the particular naval operating environment of the carrier-based aircraft ski-jump takeoff, the integrated dynamic simulation models of multi-body system are developed, which involves the movement entities of the carrier, the aircraft and the landing gears, and involves takeoff instruction, control system and the deck wind disturbance. Based on Matlab/Simulink environment, the multi-body system simulation is realized. The validity of the model and the rationality of the result are verified by an example simulation of carrier-based aircraft ski-jump takeoff. The simulation model and the software are suitable for the study of the multidiscipline intersection problems which are involved in the performance, flight quality and safety of carrier-based aircraft takeoff, the effects of landing gear loads, parameters of carrier deck, etc.     

A model for discrimination and prediction of mental workload of aircraft cockpit display interface

With respect to the ergonomic evaluation and optimization in the mental task design of the aircraft cockpit display interface, the experimental measurement and theoretical modeling of mental workload were carried out under flight simulation task conditions using the performance evaluation, subjective evaluation and physiological measurement methods. The experimental results show that with an increased mental workload, the detection accuracy of flight operation significantly reduced and the reaction time was significantly prolonged; the standard deviation of R-R intervals（SDNN） significantly decreased, while the mean heart rate exhibited little change; the score of NASA_TLX scale significantly increased. On this basis, the indexes sensitive to mental workload were screened, and an integrated model for the discrimination and prediction of mental workload of aircraft cockpit display interface was established based on the Bayesian Fisher discrimination and classification method. The original validation and cross-validation methods were employed to test the accuracy of the results of discrimination and prediction of the integrated model, and the average prediction accuracies determined by these two methods are both higher than 85%. Meanwhile, the integrated model shows a higher accuracy in discrimination and prediction of mental workload compared with single indexes. The model proposed in this paper exhibits a satisfactory coincidence with the measured data and could accurately reflect the variation characteristics of the mental workload of aircraft cockpit display interface, thus providing a basis for the ergonomic evaluation and optimization design of the aircraft cockpit display interface in the future.     

ANALYSIS OF LEAKAGE CHARACTERISTICS OF LABYRINTH SEALS

This paper presents the leakage characteristics of labyrinth seals, which were introduced by theoretical analysis and experiment results. The study of the dissipative process converting the kinetic energy to the thermal energy within the labyrinth chamber is emphasized. Experiments were carried out using a model of Straight-Through Labyrinth. By changing the Reynolds number, pressure ratio, and the ratios of clearance and depth to the length of the chambers, the flow coefficient, carry-over factor and ideal labyrinth function can be determined. Additionally, by applying the continuity equation, energy equation. Bernoulli's equation and the equation of state to the vortex chambers, a closed set of equations is obtained. Solving the equations simultaneously and numerically, the velocity, pressure and temperature in each vortex- chamber can be determined completely. Finally, the leakage of the labyrinth is acquired.     

Deformation Compensation of Ram Components of Super-heavy-duty CNC Floor Type Boring and Milling Machine

Ram is a very important component of super-heavy-duty computer numerical control (CNC) floor type boring-milling machine, and deformation of ram is a significant source causing errors in machining process. To compensate the deformation error of super-heavy-duty CNC floor type boring-milling machine, based on force analysis theory, the law and compensation measures of deformation of ram are researched. Based on the principle of torque (force) balance of the ram components, the formulas of compensation forces and compensation torques are derived, the relations between compensation forces (compensation torques) and the stroke distance of the ram are given. According to theoretical analysis results and the structural characteristics of super-heavy-duty CNC floor type boring and milling machine of TK6932, rods compensation, hydrostatic pressure compensation and wire rope compensation measures are taken to compensate the deformation error of ram. The experiments and computer simulation results show that the straightness of the ram at its overhanging end meets the national machinery industry standards.     

Flight dynamics modeling of a small ducted fan aerial vehicle based on parameter identifcation

This paper presents a simple and useful modeling method to acquire a dynamics model of an aerial vehicle containing unknown parameters using mechanism modeling,and then to design different identifcation experiments to identify the parameters based on the sources and features of its unknown parameters.Based on the mathematical model of the aerial vehicle acquired by modeling and identifcation,a design for the structural parameters of the attitude control system is carried out,and the results of the attitude control flaps are verifed by simulation experiments and flight tests of the aerial vehicle.Results of the mathematical simulation and flight tests show that the mathematical model acquired using parameter identifcation is comparatively accurate and of clear mechanics,and can be used as the reference and basis for the structural design.     

基于静强度分布的复合材料疲劳寿命分布的预测模型(英文)

The reasons of the static strength dispersion and the fatigue life dispersion of composite laminates are analyzed in this article. It is concluded that the inner original defects, which derived from the manufacturing process of composite laminates, are the common and major reason of causing the random distributions of the static strength and the fatigue life. And there is a correlative relation between the two distributions. With the study of statistical relationship between the fatigue loading and the fatigue life in the uniform confidence level and the same survival rate S-N curves of material, the relationship between the static strength distribution and the fatigue life distribution through a material S-N curve model has been obtained. And then the model which is used to describe the distributions of fatigue life of composites, based on their distributions of static strength, is set up. This model reasonably reflects the effects of the inner original defects on the static strength dispersion and on the fatigue life dispersion of composite laminates. The experimental data of three kinds of composite laminates are employed to verify this model, and the results show that this model can predict the random distributions of fatigue life for composites under any fatigue loads fairly well.     

Experimental study of flow field distribution over a generic cranked double delta wing

The flow fields over a generic cranked double delta wing were investigated. Pressure and velocity distributions were obtained using a Pitot tube and a hot wire anemometer. Two different leading edge shapes, namely ‘‘sharp" and ‘‘round", were applied to the wing. The wing had two sweep angles of 55° and 30°. The experiments were conducted in a closed circuit wind tunnel at velocity 20 m/s and angles of attack of 5°–20° with the step of 5°. The Reynolds number of the model was about 2 ×10~5 according to the root chord. A dual vortex structure was formed above the wing surface. A pressure drop occurred at the vortex core and the root mean square of the measured velocity increased at the core of the vortices, reflecting the instability of the flow in that region. The magnitude of power spectral density increased strongly in spanwise direction and had the maximum value at the vortex core. By increasing the angle of attack, the pressure drop increased and the vortices became wider; the vortices moved inboard along the wing, and away from the surface; the flow separation was initiated from the outer portion of the wing and developed to its inner part. The vortices of the wing of the sharp leading edge were stronger than those of the round one.     

Comparative Study on Super Fine Mesophase Powder and MCMB Used to Manufacture High-Density Isotropic Carbon Bulks

Mesocarbon microbeads (MCMB) and super fine mesophase powder (SFMP) were prepared firstly from a coal tar pitch and then hot-condensed into high-density isotropic carbon (HDIC) bulks under 160 MPa and finally sintered at 1 000 ℃ . By analyzing the ther-mogravimetric behavior of the MCMB and SFMP powders, their volume shrinkage and weight loss during sintering and the bulk density and flexural strengths of their sintered bulks, it was found that the smaller sizes and the richer β-resin contents of SFMP have facilitated formation of sintered bulks with more compact isotropic structure and higher flexural strengths than MCMB. Because of the filling and bonding effects of SFMP on MCMB bulks, addition of SFMP, albeit a little, can greatly increase the flexural strengths of sintered bulks of MCMB. However, adding MCMB, even a slight amount, into SFMP can severely impair the flexural strength of sintered bulks. This might be attributed to both the crack initiation along the boundaries between MCMB and SFMP and the formation of layered texture of MCMB sphere.     

Modeling of a space flexible probe–cone docking system based on the Kane method

Recent developments in micro- and nano-satellites have attracted the interest of the research community worldwide. Many colleges and corporations have launched their satellites in space. Meanwhile, the space flexible probe–cone docking system for micro- and nano-satellites has become an attractive topic. In this paper, a dynamic model of a space flexible probe–cone docking system, in which the flexible beam technology is applied, is built based on the Kane method. The curves of impact force versus time are obtained by the Lagrange model, the Kane model, and the experimental method. The Lagrange model was presented in the reference and verified by both finite element simulation and experiment. The results of the three methods show good agreements on the condition that the beam flexibility and the initial relative velocity change. It is worth mentioning that the introduction of vectorial mechanics and analytical mechanics in the Kane method leads to a large reduction of differential operations and makes the modeling process much easier than that of the Lagrange method. Moreover, the influences of the beam flexibility and the initial relative velocity are discussed. It is concluded that the initial relative velocity of space docking operation should be controlled to a certain value in order to protect the docking system. a 2014 Production and hosting by Elsevier Ltd. on behalf of CSAA BUAA.