共查询到20条相似文献,搜索用时 62 毫秒
1.
以聚锆氧烷PNZ 为锆源、炔丙基酚醛PN 为碳源制备了一种ZrC 液相陶瓷前驱体PNZ-PN,该前
驱体经1 600℃热解能够转化为高度结晶的ZrC 陶瓷。通过FT-IR、DSC、TGA 对前驱体的固化过程及固化样
的热失重行为进行了分析;通过XRD、元素分析和SEM 对热解产物的晶相组成及微观形貌进行了分析。结果
表明:1 200℃以下,热解产物主要是ZrO2,1 400℃时开始发生碳热还原反应出现结晶度较小的ZrC,经1 600℃
热解后可完全转化为ZrC;PN 的加入量会影响热解过程中陶瓷样品的ZrO2 晶相及1 600℃热解产物的碳含量,
通过调整PN 的加入量最终可得到自由碳含量1. 66%、近似纯相的ZrC 陶瓷;得到的陶瓷粒子Zr、C 元素分布
均匀、粒径主要分布为100 ~200 nm。 相似文献
驱体经1 600℃热解能够转化为高度结晶的ZrC 陶瓷。通过FT-IR、DSC、TGA 对前驱体的固化过程及固化样
的热失重行为进行了分析;通过XRD、元素分析和SEM 对热解产物的晶相组成及微观形貌进行了分析。结果
表明:1 200℃以下,热解产物主要是ZrO2,1 400℃时开始发生碳热还原反应出现结晶度较小的ZrC,经1 600℃
热解后可完全转化为ZrC;PN 的加入量会影响热解过程中陶瓷样品的ZrO2 晶相及1 600℃热解产物的碳含量,
通过调整PN 的加入量最终可得到自由碳含量1. 66%、近似纯相的ZrC 陶瓷;得到的陶瓷粒子Zr、C 元素分布
均匀、粒径主要分布为100 ~200 nm。 相似文献
2.
3.
研究了一种在C/C复合材料中掺杂难熔金属化合物的新方法:溶胶-凝胶法。利用醋酸锆溶胶对密度为1.39和1.59 g/cm3的C/C复合材料进行浸渍,凝胶化后,再进行炭化处理,在C/C复合材料中引入了难熔金属化合物ZrC。经若干次处理后,两种C/C复合材料的密度最终分别达到1.88和1.86 g/cm3。利用电子背散射测试观察Zr在C/C复合材料中的分布,发现在C/C复合材料表面多次凝胶沉积形成一层Zr的涂层,而在材料的内部Zr的分布主要依赖于材料本身孔洞的分布以及纤维束间的孔隙。对电弧烧蚀后的Zr-C/C复合材料进行表观形貌观察,发现在材料表面形成均匀的ZrO2膜,将基体与氧气隔绝,从而减缓材料的烧蚀速率。 相似文献
4.
ZrC作为一种先进的高温结构陶瓷材料,在航空航天、清洁能源(第四代核技术)等领域具有广泛的应用。本文主要综述了ZrC粉体的制备技术,主要有直接合成法、机械合金化法、自蔓延高温合成法、碳热还原法、溶胶-凝胶法、液相前驱体法、激光气相反应法和高频等离子体法等,详细分析了各制备技术的特点。 相似文献
5.
6.
采用溶胶-凝胶法,以钛酸丁酯为前驱体,乙二醇作为螯合剂制备纳米TiO2 粒子。考察钛的乙二
醇盐的浓度、pH 值、温度等因素对TiO2 粒径的影响,并用红外光谱和SEM 对纳米TiO2 粒子进行结构和形貌表
征。结果表明,采用溶胶凝胶法可以制备出呈椭圆形且粒径分布均匀的TiO2 纳米粒子。使用硝酸铵可以有效
阻止TiO2 纳米粒子团聚。当pH 值为2 ~3、温度为20 ~40℃,钛的乙二醇盐在丙酮中的浓度为0. 03、0. 05 及
0. 07 M 时,粒径分别为150、240 及600 nm。
相似文献
7.
碳化锆超高温陶瓷在航空航天、核工艺、电子等领域有广阔的应用前景。为了改善ZrC陶瓷的烧结及力学性能,以ZrO_2粉和TaO_2粉为原料,采用碳热还原法制备TaC与ZrC固溶体粉末,热压烧结工艺制备ZrC-TaC陶瓷,探索烧结温度和TaC含量对陶瓷固溶体的固溶行为、致密化行为、组织结构和力学性能的影响规律。结果表明:当烧结温度从2000℃升高到2050℃时,TaC在ZrC中的固溶度提高;当TaC含量从5%升高到15%时,陶瓷的致密度、维氏硬度和弹性模量单调下降,抗弯强度没有明显规律,断裂韧度随着TaC含量的增加逐渐减小。 相似文献
8.
9.
10.
采用碳热还原氮化SiO2的方法在1 500℃制备了Si2N2O,并通过XRD和热失重分析,研究了Fe2O3对合成Si2N2O的催化作用及机理。Fe2O3对Si2N2O的合成具有显著的催化作用,加入少量Fe2O3可以使SiO2的转化率达到100%。Fe2O3的催化机理为:一方面,Fe2O3被C还原为纳米铁单质,并与Si形成Fe-Si液相,该Fe-Si液相可溶解SiO2和C颗粒,促使SiOC中间相在较低温度下形成,从而显著降低碳热还原反应的开始温度。另一方面,Fe-Si液相中的CO2与FeSi反应,通过形成SiO和CO而加速碳热还原反应的进行。 相似文献
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:2,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
14.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
15.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
16.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
17.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
18.
(高)超声速流动试验技术及研究进展 总被引:1,自引:1,他引:1
近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。 相似文献
19.
Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis 总被引:2,自引:0,他引:2
GAO Hong-liang ZHANG Hui WANG Shu-juan 《中国航空学报》2007,20(1):75-80
Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved. 相似文献