基于三类非线性函数的认证码的构造

为了将高度非线性函数应用于认证码构造理论．讨论了非线性函数的度量，给出了由三类非线性函数构造的Cartesian认证码，并且当编码规则按等概率分布选取时，分别计算了三类认证码的模仿攻击和欺骗攻击成功的概率。结果表明，第二类认证码模仿攻击成功的概率达到了下界。在n取值相同的条件下，第一类认证方案模仿攻击成功的概率比第三类的大。     

基于非线性函数认证码的新构造

基于非线性函数构造了一类新的认证码,计算出了该认证码替换攻击成功的概率和模仿攻击成功的概率,并与前人所做的认证码进行了比较,分析了所构造认证码的优缺点。     

MIMO雷达中一种降维MUSIC的相干角度估计算法

研究单快拍下双基地多输入多输出（Multiple—InputMultiple-Output,MIMO）雷达中相干信源的离开角（Directionofdeparture,DOD）与到达角（directionofarrival,DOA）联合估计问题。利用单快拍下双基地MIMO雷达的接收信号构造一组Toeplitz矩阵,利用这组ToepIitz矩阵重构一个信号矩阵,提出一种基于降维多重信号分类（ReducedDimensionMultipleSignalClassification,RD-MUSIC）的DOD与DOA联合估计算法。提出的算法能够有效估计相干信源以及非相干信源的角度,实现角度的自动配对,并且角度估计性能远优于FBSS—ESPRIT算法以及ESPRIT-like算法。仿真结果验证了算法的有效性。     

利用有限域上二元多项式构造带仲裁的认证码

在传统的无条件安全认证码中,假定发方和收方是相互信任的,他们不会互相欺骗。但有些情况也可能不是这样,发方在发出一个消息后,不承认是他发的,收方捏造了一个消息,声称来自发方,在这种情况下就需要增添仲裁方。带仲裁的认证码能解决通信系统中发方与收方互不信任的问题。利用有限域上二元多项式构造了一个带仲裁的认证码,并计算了所构造码的参数。当编码规则按等概率分布选取时,计算出了敌方与收方成功模仿攻击和成功替换攻击的最大概率．以及发方成功模仿攻击的最大概率。     

基于辛几何构作一类新的带仲裁的认证码

具有仲裁的认证码既要防止敌手的欺骗,又要防止收方和发方的互相欺骗。利用有限域上辛几何构造了一类具有仲裁的认证码,计算了其容量参数。假设编码规则是按照均匀概率分布选择,给出了敌手模仿攻击、敌手替换攻击、发方模仿攻击、收方模仿攻击和收方替换攻击的成功概率。研究结论表明可用辛几何构作许多带仲裁的认证码。     

基于加权融合的多信源弹道数据实时野值检测方法

研究多信源弹道数据实时处理中斑点野值的检测问题.通过计算各信源数据的实时精度,给出了具有自适应加权系数的加权融合方法,实现了对目标状态参数较高精度的估计,从而实时、准确、高效地检测各信源数据野值.仿真结果表明,本方法可以快速、有效地检测多信源数据的斑点野值,解决因数据切换带来的台阶跳跃问题.     

利用奇异辛几何构作新的带仲裁的认证码

利用有限域上奇异辛几何构造了一个新的带仲裁的认证码，并计算了这个码的参数。当收方和发方的编码规则按等概率分布选取时，计算出了各种攻击成功的概率。     

一种基于协方差矩阵重构的相干信源DOA估计算法

针对空间相干信源的波达方向估计问题,提出了一种基于协方差矩阵重构的TSVD-ESPRIT算法。它利用包含所有信源信息的特征向量构造Toeplitz协方差矩阵,避免了阵列有效孔径的损失,分辨率高且稳定性好;并且利用ESPRIT算法代替MUSIC算法进行DOA估计,避免了谱峰搜索,大大降低了计算量。数据仿真和分析证明了该算法的正确性和有效性。     

无人机网络中数控分离的安全传输机制

数据和飞控指令的安全性是无人机网络安全性的一个重要方面。针对现有的无人机网络安全机制中的不足，本文提出了一种数控分离的安全传输机制。针对无人机向地面站发送的数据采用基于高级加密标准的计数器和密文分组链接消息认证码（AES-CCM）认证加密机制的数据安全传输协议，保证数据的机密性和完整性，针对地面站向无人机发送的飞控指令设计了基于一次签名的飞控广播认证协议，保证飞控指令的完整性。通过安全性分析，证明所提出的方案能够保护数据的机密性和完整性，以及飞控指令的完整性。最后，通过仿真试验分析了所提出方案的性能，结果表明，所提出的数据安全传输协议发送100B和1KB的消息时，平均每个消息的认证加密时间和解密验证时间均不超过1ms；所提出的飞控广播认证协议在使用不同的哈希函数时，对1MB的飞控指令生成签名和验证签名的时间为1～2.7ms，在实际应用中具有高效性。     

利用非交错对称矩阵构造Cartesian认证码

利用特征为2的有限域上非交错对称矩阵构造了一个Cartesian认证码，并计算出其参数。进而，假定编码规则按照均匀的概率分布所选取，计算出了该码被模仿攻击成功的最大概率只和被替换攻击成功的最大概率Ps。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.