改进草酸盐共沉淀法制备钛酸钡超细粉体的研究

根据传统的草酸盐共沉淀法合成超细BaTiO3粉末易产生偏离四方相的特点,提出了一种改进的草酸盐共沉淀法制备BaTiO3粉体的方法.利用改进的草酸盐共沉淀法在700℃制备出了各向同性的四方相纳米尺寸的BaTiO3粉体,煅烧温度比常规的草酸盐共沉淀法降低了100℃左右;粉体平均粒径约30nm,颗粒均匀,且制备出的粉体具有良好的热稳定性.     

铁氧体吸收剂粉体的煅烧工艺研究

研究了铁氧体吸收剂粉体的煅烧工艺对粉体的性能、形貌和相组成的影响.研究表明,粉体的形貌和相组成对其复数磁导率有较大影响.经过对煅烧工艺进行优化,制备出了较高性能的吸收剂粉体.     

用硫化铵制备纳米二硫化钼固体润滑剂微粒

以钼酸铵和硫化铵为原料,通过化学沉淀法制备了前驱体三硫化钼.再经过氢气份脱硫制备了纳米二硫化钼固体润滑剂微粒.利用透射电子显微镜(TEM)、激光粒度分析仪和X射线衍射(XRD)对粉体粒子形貌、大小和相结构进行了分析.结果表明:制备纳米二硫化钼微粒的条件为pH值为6.0.煅烧温度为500℃,保温时间为30min,所得微粒粒径为20～40 nm左右的球形颗粒.     

硝酸根与柠檬酸的摩尔比对低温燃烧合成钛酸钡的影响

以Ba(NO3)2-TiO2-C6H7O8@H2O为体系,在600℃的加热温度下进行低温燃烧合成实验,制得粒度为200n～350nm的四方相BaTiO3陶瓷粉体.研究表明体系中硝酸根与柠檬酸的摩尔比为2.5～3.0时,体系燃烧最完全,形成比表面高(2.47m2/g)、颗粒细小、孔隙率大的钛酸钡粉末.     

压制工艺和粒径对粉末冶金Ti-1Al-8V-5Fe合金组织性能的影响

采用粉末冶金技术以氢化钛（TiH₂）粉和不同粒径的元素粉体为原料制备Ti-1Al-8V-5Fe（Ti-185）合金,研究了压制工艺对不同粒径元素粉制备的Ti-185合金组织及性能的影响。结果表明：当压制压力在800 MPa、保压时间80 s、压制速率为1 mm/s时,Ti-185生坯密度最高,为最佳压制工艺。由粒径较小元素粉制备得到的Ti-185合金晶粒越细小,合金的烧结致密度就越高。粉末粒径越小,烧结过程中合金元素实现合金化需要扩散的距离就越短,越有利于合金力学性能的提高,其中具有最小粒径的样品表现出最高的硬度（43 HRC）和强度（1 438 MPa）。     

高热导率聚酰亚胺浸渍漆

文摘通过引入无机纳米粉体研制了高热导率聚酰亚胺浸渍漆,研究了聚酰亚胺的化学结构、无机粉体的种类、粒径和用量等因素对浸渍漆贮存稳定性以及固化物性能的影响。均苯四甲酸二酐与4,4′-二氨基二苯基醚合成的聚酰亚胺具有高的热导率。在联苯型聚酰亚胺中引入30%~35%、粒径为100~300 nm的α-A l2O3粉体,固化物的热导率可提高到0.65~0.80 W/(m.K),其余性能基本保持原有水平。     

SHS法制备硼化物陶瓷粉体的表征分析

采用自蔓延高温还原合成方法制备TiB2,TiB2-Al2O3和ZrB2-Al2O3陶瓷粉末.利用XRD,XPS,SEM以及TEM等分析测试手段对合成粉末进行表征和分析.结果表明,TiB2,ZrB2和Al2O3分别以主晶相的形式存在于所合成的各自粉体之中.相比之下,TiB2单相陶瓷粉末颗粒分布较宽.由于自蔓延高温合成(SHS)温度很高,部分颗粒形成团聚,宏观上使颗粒的平均粒径变大(＞5μm);而TiB2-Al2O3和ZrB2-Al2O3复合陶瓷粉末,因合成过程中Al2O3的形成,使得颗粒粒度分布明显变窄,分布均匀,颗粒尺寸也相应减小.分析认为这主要与复合粉末合成过程中,不同颗粒间形成良好结合的界面有关.     

高频热等离子体法合成纳米ZrC粉体及其表征

以炭黑和甲烷分别作为碳源,四氯化锆作为锆源,采用高频热等离子体法合成了超细ZrC粉体。分别采用XRD、高频红外燃烧、SEM、化学重量法对实验产物进行了表征,分析了超细ZrC粉体的物相、纯度、粒径与碳源及进气量之间的影响规律。研究表明:采用不同碳源所合成的ZrC粉体粒径均在100 nm以下,相比较炭黑为碳源,甲烷作为碳源合成的产品纯度高,氧含量低,产率大,因此,甲烷作为碳源更适于批量制备超细ZrC粉体。     

纳米CeO2粉体的制备及其发光性能研究

以氨水和硝酸铈为反应原料,采用沉淀滴定法制备了纳米CeO2粉体,通过XRD、SEM、TEM等手段对其进行了结构表征和形貌分析;考察了不同溶剂、煅烧温度等对其颗粒尺寸的影响;应用荧光光谱法测试了其发光光谱,首次探讨了纳米CeO2粉体的发光性能。结果表明,前驱体经过300～700℃煅烧后可以得到颗粒尺寸为4-30nm的立方萤石结构CeO2晶体,其形貌接近于球形。在无水乙醇溶剂中得到的纳米CeO2颗粒分散较好,其颗粒尺寸随煅烧温度的升高而增大。纳米CeO2粉体具有良好的蓝光发光性能,在276nm的激发波长作用下,其发射光谱的最大峰值为473nm。     

纳米结构莫来石粉体喂料的制备与表征

环境障涂层（Environmental barrier coating,EBC）是设立在服役环境和发动机材料之间阻止或减小环境对发动机侵蚀的表面防护层。莫来石具有良好的耐高温性、化学兼容性、抗氧化性和导热性,被视为环境障涂层的重要材料。对纳米结构莫来石粉体喂料的制备工艺进行了研究,目的是制备出球形度好、表面光滑、流动性好、致密度高的纳米结构粉体喂料。以纳米Al2O3、SiO2粉体为原材料,采用湿法球磨、喷雾干燥、固相烧结的方法制备了用于环境障涂层的纳米结构莫来石粉体喂料。借助X射线衍射仪和扫描电镜研究了粉体喂料在不同热处理温度下的组织与形貌。结果显示,1300℃+150 min的固相烧结的球形度与喷雾干燥所得的球形度保持一致,表面也较为光滑,缺陷较少,莫来石粉体喂料的粒径在60μm左右,晶粒为纳米结构。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.