Target Detection and Parameter Estimation for MIMO Radar Systems

We investigate several target detection and parameter estimation techniques for a multiple-input multiple-output (MIMO) radar system. By transmitting independent waveforms via different antennas, the echoes due to targets at different locations are linearly independent of each other, which allows the direct application of many data-dependent beamforming techniques to achieve high resolution and excellent interference rejection capability. In the absence of array steering vector errors, we discuss the application of several existing data-dependent beamforming algorithms including Capon, APES (amplitude and phase estimation) and CAPES (combined Capon and APES), and then propose an alternative estimation procedure, referred to as the combined Capon and approximate maximum likelihood (CAML) method. Via several numerical examples, we show that the proposed CAML method can provide excellent estimation accuracy of both target locations and target amplitudes. In the presence of array steering vector errors, we apply the robust Capon beamformer (RCB) and doubly constrained robust Capon beamformer (DCRCB) approaches to the MIMO radar system to achieve accurate parameter estimation and superior interference and jamming suppression performance.     

Adaptive nulling of SAR sidelobe discretes

By using adaptive subarrays for crossrange imaging we have developed a computationally simple method that removes any image degradation caused by strong, discrete clutter located in the crossrange sidelobes of a synthetic aperture radar (SAR) image. The procedure is based on the minimization of the mean interference power with the constraint that the image of a desired scatterer is undistorted. The applicability of the approach has been illustrated by simulation     

雷达抗干扰能力度量方法的研究

 本文论述了度量雷达抗干扰能力的方法,提出了一组通用的度量公式。这些公式的基本部分是由雷达的主要技术参数组成。代表雷达的潜在抗干扰能力。公式的补充部分是由雷达各种抗干扰技术措施的指标所组成,代表这些抗干扰措施的质量水平。用这组公式可以计算出雷达抗消极干扰能力、抗积极干扰能力与综合抗干扰能力的表征数值。本文给出了计算举例,讨论了计算结果在雷达系统分析与总体设计中的应用。     

STAP for clutter suppression with sum and difference beams

A unique approach for airborne radar clutter rejection is developed and evaluated. This spatial and temporal adaptive approach employs the sum and difference beams of an antenna, which has significant practical advantages because it can be implemented with no/little change to the front-end electronics of airborne systems where sum and difference beams already exist for other reasons. The low sidelobe implementation of many sum and difference beam systems and the low gain of the difference beam in the direction of the target gives this approach the potential in many radars for a more predictable response pattern. The impact of these factors is shown in an airborne clutter rejection demonstration where the performance of this approach is compared with that of the factored approach (FA) using additional spatial channels and that of conventional pulse-Doppler (PD) processing. Reliable detection of an injected target is only achieved by this approach     

HRR Detector for Slow-Moving Targets in Sea Clutter

The radar detection of targets in the presence of sea clutter has historically relied upon the radial velocity of targets with respect to the radar platform either by exploiting the relative target Dopplers (for targets with sufficient radial velocity) or by discerning the paths targets traverse from scan to scan. For targets with little to no radial velocity component, though, it can become quite difficult to differentiate targets from the surrounding sea clutter. This paper addresses the detection of slow-moving targets in sea clutter using a high resolution radar (HRR) such that the target has perceptible extent in range. Under the assumption of completely random sea clutter spikes based on an epsiv-contaminated mixture model with the signal and clutter powers known, optimal detection performance results from using the likelihood ratio test (LRT). However, for realistic sea clutter, the clutter spikes tend to be a localized phenomenon. Based upon observations from real radar data measurements, a heuristic approach exploiting a salient aspect of the idealized LRT is developed which is shown to perform well when applied to real measured sea clutter.     

Generalized radar clutter model

A commonly used density model for radar clutter is chi-square for power, or, equivalently, Rayleigh for amplitude. However, for many modern high resolution radar systems, this density underestimates the tails of the measured clutter density. Log normal and Weibull distributions have proved to be better suited for the clutter in these high resolution radars. Generalizing the chi-square density by replacing it with the noncentral chi-square density and allowing the mean power level (the noncentrality parameter) to vary, we can both suitably shape the clutter density to produce larger tails and model the fluctuation of the average clutter power, commonly referred to as speckle. The resulting form, although appearing cumbersome, readily allows for efficient and accurate computations of the probability of detection in clutter     

两种自适应方向图峰值副瓣控制方法比较

自适应阵列（或称自适应波束形成）目前已广泛应用到雷达、声纳和通信领域中用来抑制各种干扰（有意的干扰，杂波干扰和多用户干扰等）。在雷达应用中，为了减轻脉冲欺骗式干扰或旁瓣目标并利用单脉冲雷达来准确测量目标波达方向．要求自适应方向图具有低副瓣和稳定的主瓣形状。在实际应用中，各种失配误差将降低自适应阵列的性能．这些误差包括由于目标的波达方向不精确引起的信号指向误差，由通道失配和位置扰动引起的阵列校准误差和由小样本教引起的协方差矩阵估计误差。在此情况下，自适应波束形成的性能大大下降（干扰抑制性能变差。主瓣失真和高的副瓣）。已提出了一种基于二次约束的集成峰值副瓣控制（integrated peak sidelobe control，简称IPSC）方法。该方法可以精确地控制峰值副瓣电平并产生具有稳定的主瓣形状的自适应方向图。研究IPSC中目标信号的影响和信号消除方案以进一步提高IPSC的性能。并将IPSC方法和最新提出的基于二阶锥规划（second-order cone programming，简称SOCP）的分布式峰值副瓣控制（distfibuted peak sidelobe control，简称为DPSC）新方法在性能上进行了比较。仿真结果表明。在干扰抑制性能和方向图控制质量方面IPSC比DPSC性能优越。此外IPSC比DPSC计算高效。     

High-resolution SAR imaging with angular diversity

We propose to use the APES (amplitude and phase estimation) approach for the spectral estimation of gapped data and synthetic aperture radar (SAR) imaging with angular diversity. A relaxation-based algorithm, referred to as GAPES (Gapped-data APES), is proposed, which includes estimating the spectrum via APES and filling in the gaps via a least squares (LS) fitting. For SAR imaging with angular diversity data fusion, we perform one-dimensional (1-D) windowed fast Fourier transforms (FFTs) in range, use the GAPES algorithm to interpolate the gaps in the aperture for each range, apply 1-D inverse FFTs (IFFTs) and dewindow in range, and finally apply the two-dimensional (2-D) APES algorithm to the interpolated matrix to obtain the 2-D SAR image. Numerical results are presented to demonstrate the effectiveness of the proposed algorithm     

Sum-difference Reduced-dimensional Processing in SAR Image Domain and Statistical Analysis for Ground Moving Target Indication

In this article, a new reduced-dimensional adaptive processing algorithm based on joint pixels sum-difference data for clutter rejection is proposed. The sum-difference data are obtained by orthogonal projection of the joint pixels data of different synthetic aperture radar (SAR) images generated by a multi-satellite radar system. In the sense of statistical expectation, the sum-differ- ence data contain the common and different information of the SAR images. Therefore, the objective of clutter cancellation can be achieved by adaptive processing. Moreover, based on the residual image after clutter rejection, statistical analysis of constant false-alarm rate (CFAR) detection of moving targets is also presented. Simulation results demonstrate the effectiveness and robustness of the proposed algorithm even with heterogeneous clutter and image co-registration error.     

High Range-Resolution Monopulse Tracking Radar

High range-resolution monopulse (HRRM) tracking radar which maintains wide instantaneous bandwidth through both range and angle error sensing channels provides range, azimuth, elevation, and amplitude for each resolved part of the target. The three-dimensional target detail can be used to improve and extend radar performance in several ways: for improved precision of target location, for target classification and recognition, to counter repeater-type ECM, to improve low-angle multipath tracking, to resolve multiple targets, as a miss-distance measurement capability, and for improved tracking in chaff and clutter. These have been demonstrated qualitatively except for the ECCM to repeater ECM and low-altitude tracking improvement. Initial results from an experimental HRRM radar with 3-ns pulse length show resolution of aircraft into its major parts and precise location of each resolved part accurately in range and angle. Realtime closed-loop tracking is performed on aircraft in flight using high-speed sampled, digitized, and processed HRRM range and angle video data. Clutter rejection capability is also demonstrated.     

Rotating Blades Radio Interference in a Helicopter-Borne CW Doppler Radar

Radio interference generated in a helicopter-borne continuous wave (CW) Doppler radar system due to the rotating blades is analyzed. This problem has been previously treated for the case of pulse Doppler radar systems with very narrow (near zero) beamwidth. In this case the strong interference component returning directly from the blades (with no ground reflection) need not be considered as it reaches the receiver when it is still blinded. In the case of a CW Doppler radar, however, this interference component must be included. Numerical calculations show that the total blade interference power level, dominated by the direct component, is higher than that of the direct ground clutter in the radar clutter region. It decreases approximately as (f - fo)-4 in the radar clear region. It stays, however, well above the thermal noise level which might cause false alarm and degrade the radar performance.     

A novel target detection approach based on adaptive radar waveform design

To resolve problems of complicated clutter, fast-varying scenes, and low signal-clutterratio (SCR) in application of target detection on sea for space-based radar (SBR), a target detection approach based on adaptive waveform design is proposed in this paper. Firstly, complicated sea clutter is modeled as compound Gaussian process, and a target is modeled as some scatterers with Gaussian reflectivity. Secondly, every dwell duration of radar is divided into several sub-dwells. Regular linear frequency modulated pulses are transmitted at Sub-dwell 1, and the received signal at this sub-dwell is used to estimate clutter covariance matrices and pre-detection. Estimated matrices are updated at every following sub-dwell by multiple particle filtering to cope with fast-varying clutter scenes of SBR. Furthermore, waveform of every following sub-dwell is designed adaptively according to mean square optimization technique. Finally, principal component analysis and generalized likelihood ratio test is used for mitigation of colored interference and property of constant false alarm rate, respectively. Simulation results show that, considering configuration of SBR and condition of complicated clutter, 9 dB is reduced for SCR which reliable detection requires by this target detection approach. Therefore, the work in this paper can markedly improve radar detection performance for weak targets.     

Angle/Doppler estimation in heavy-tailed clutter backgrounds

This work describes new methods on the modeling of the amplitude statistics of airborne radar clutter by means of alpha-stable distributions. We develop joint target angle and Doppler, maximum likelihood-based estimation techniques from radar measurements retrieved in the presence of impulsive uncorrelated noise modeled as an alpha-stable random process. We derive the Cramer-Rao bounds (CRBs) for the additive Cauchy interference scenario to assess the best case estimation accuracy which can be achieved. In addition, we introduce a new joint spatial- and Doppler-frequency high-resolution estimation technique based on the fractional lower order statistics of the measurements of a radar array. Simulation results demonstrate that the proposed methods can be of interest in the study of space-time adaptive processing (STAP) for airborne pulse Doppler radar arrays operating in impulsive interference environments     

Airborne/spacebased radar STAP using a structured covariance matrix

It is shown that partial information about the airborne/spacebased (A/S) clutter covariance matrix (CCM) can be used effectively to significantly enhance the convergence performance of a block-processed space/time adaptive processor (STAP) in a clutter and jamming environment. The partial knowledge of the CCM is based upon the simplified general clutter model (GCM) which has been developed by the airborne radar community. A priori knowledge of parameters which should be readily measurable (but not necessarily accurate) by the radar platform associated with this model is assumed. The GCM generates an assumed CCM. The assumed CCM along with exact knowledge of the thermal noise covariance matrix is used to form a maximum likelihood estimate (MLE) of the unknown interference covariance matrix which is used by the STAP. The new algorithm that employs the a priori clutter and thermal noise covariance information is evaluated using two clutter models: 1) a mismatched GCM, and 2) the high-fidelity Research Laboratory STAP clutter model. For both clutter models, the new algorithm performed significantly better (i.e., converged faster) than the sample matrix inversion (SMI) and fast maximum likelihood (FML) STAP algorithms, the latter of which uses only information about the thermal noise covariance matrix.     

Automated Tracking for Aircraft Surveillance Radar Systems

An improved moving target detector (MTD) (a digital signal processor) has been designed, constructed, and tested which successfully rejects all forms of radar clutter while providing reliable detection of all aircraft within the coverage of the radar. The MTD is being tested on both terminal and enroute surveillance radars for the FAA. This processor has been integrated with automatic tracking algorithms to give complete rejection of ground clutter, heavy precipitation, and angels (birds).     

Radar Properties of Non-Rayleigh Sea Clutter

Measurements of sea clutter at low grazing angles using high- resolution radar show that the probability density p(x) of envelope detected sea clutter is not Rayleigh. Using the composite surface scattering model, a special varying clutter density p(x|?0) is proposed and is used to explain the non-Rayleigh nature of clutter. Since the clutter distribution has an enormous effect on the performance of a radar, the variation of the clutter densities, p(x) and p(x|?0), with various radar parameters such as frequency, pulsewidth, and polarization is found. Finally, a simulation of the composite surface scattering model is performed, and it verifies the effect of the various parameters on p(x).     

NEW METHOD FOR REDUCED RANK STAP—NON CLUTTER CHANNEL METHOD

Space- time adaptive processing(STAP) is aleading technology candidate for improving detec-tion performance of advanced airborne early warn-ing radar.In practical radar systems,the optimumfully adaptive space- time processing[1] cannot al-ways be implemented because of the computationalcomplexity,so the design of suboptimum proces-sors has been one of the key topics in STAP.Sev-eral reduced- rank STAP methods have been pro-posed in recent years.For example,based on thegeneralized sidelobe…     

Robust space-time adaptive processing for airborne radar in nonhomogeneous clutter environments

Space-time adaptive processing (STAP) holds tremendous potential for the new generation airborne surveillance radar, in which the phased array antennas and pulse Doppler processing mode are adopted. A new STAP approach using the multiple-beam and multiple Doppler channels is presented here for airborne phased array radar. The approach with space-time multiple-beam (STMB) architecture is robust to array errors and has very low system degrees of freedom (DOFs). Hence, it has low sample support requirement and it is very suitable for the practical planar phased array radar under nonhomogeneous clutter environments. Meanwhile, a new nonhomogeneous detector (NHD) based on the correlation dimension (CD) is also proposed here, which is used as an effective method to screen tracing data prior to detection processing. It can further improve the performance of the STAP approach in the severely nonhomogeneous clutter environments. Therefore, a scheme that incorporates the correlation dimension nonhomogeneity detector (CD-NHD) with the STMB is recommended, which we term CD-NHD-STMB. The experimental simulation results indicate that: 1) the STMB processor is robust to array element error and has high performance under nonhomogeneous clutter environments; 2) the CD-NHD is also effective on the nonhomogeneous clutter. As a result, the CD-NHD-STMB scheme is robust to array element error and nonhomogeneous clutter, and therefore available for airborne phased array radar applications.     

New Clutter Rejection Waveforms for Long-Range Radar

A frequent compromise in the design of long-range search radars has to be made between the maximum unambiguous detection range and the achievable coherent clutter rejection performance. A new class of waveforms is introduced which offers the designer a previously unavailable flexibility in arriving at radar designs with improved clutter rejection without seriously affecting the maximum unambiguous search range. The key to these new waveforms is the recognition that a class of useful N-pulse, nonrecursive, moving target indicator (MTI) canceler designs exists which only requires the radar to transmit a total of N -1 (nonuniformly spaced) pulses.     

Near-Field Analysis of Helicopter Rotating Blades Modulation Interference

A near-field analysis is carried out to obtain the level of modulation interference due to rotating blades in a helicopter-borne pulse Doppler radar system. The interference power spectra are calculated for different values of antenna depression angle and helicopter (radar) speed at a constant helicopter altitude of 300 m. Numerical results for the case of 1 kW radiated power show that blade interference level is about 5 to 8 dBW/Hz less than that of the direct ground clutter in the clutter region. It extends, however, into the clutter-free region which may cause false alarms and degradation of the radar performance.