飞机电静液作动器滑模 PID控制器设计

在多电飞机应用环境中,由于电静液作动器（Electro Hydrostatic Actuator,以下简称EHA）系统本身的强非线性与承载交变动载荷的不确定性,简单PID控制无法达到理想控制效果。提出了滑模 PID复合控制,电机电流环和转速环构成控制系统内环,以PI控制器实现电机调速;作动筒位置环为外环,以滑模控制提升系统的快速性和鲁棒性。建立了EHA数学模型,并设计了滑模控制器结构。仿真结果表明,滑模 PID复合控制方法能有效地消除超调和减小跟随误差,实现对EHA位置的精确控制。     

Motion synchronization in a dual redundant HA/EHA system by using a hybrid integrated intelligent control design

This paper presents an integrated fuzzy controller design approach to synchronize a dis-similar redundant actuation system of a hydraulic actuator (HA) and an electro-hydrostatic actu-ator (EHA) with system uncertainties and disturbances. The motion synchronous control system consists of a trajectory generator, an individual position controller for each actuator, and a fuzzy force tracking controller (FFTC) for both actuators. The trajectory generator provides the desired motion dynamics and designing parameters of the trajectory which are taken according to the dynamic characteristics of the EHA. The position controller consists of a feed-forward controller and a fuzzy position tracking controller (FPTC) and acts as a decoupled controller, improving posi-tion tracking performance with the help of the feed-forward controller and the FPTC. The FFTC acts as a coupled controller and takes into account the inherent coupling effect. The simulation results show that the proposed controller not only eliminates initial force fighting by synchronizing the two actuators, but also improves disturbance rejection performance.     

基于阻抗内环的新型力外环控制策略

对于空间装配等与环境进行交互的任务,迫切要求空间机器人具有力控制的能力。利用机器人的关节力矩传感器,提出了一种新型的基于阻抗内环的力外环控制策略。在该方法中,内环采用阻抗控制代替传统的位置控制。阻抗控制内环使机器人具有一定的柔顺性,力外环通过期望力与实际力的误差对内环的参考轨迹进行修正,实现了机器人的力跟踪控制。另外,为了验证利用关节力矩传感器间接测量末端接触力的效果,机器人末端安装了一个高精度的JR3腕力传感器用来直接测量实际接触力。在基于位置内环和阻抗内环的力外环控制方式下,进行了机器人接触刚度变化较大环境（海绵、泡沫和铁块）的力跟踪实验。实验表明,当环境刚度变化较大时,相对于传统的力外环方法,本文提出的方法能够实现稳定的力跟踪性能。尤其对于铁块这种刚度很大的环境,该方法的有效性更加明显。     

PID Controller Optimization by GA and Its Performances on the Electro-hydraulic Servo Control System

A proportional integral derivative （PID） controller is designed and attached to electro-hydraulic servo actuator system （EHSAS） to control the angular position of the rotary actuator which control the movable surface of space vehicles. The PID gain parameters are optimized by the genetic algorithm （GA）. The controller is verified on the new state-space model of servo-valves attached to the physical rotary actuator by SIMULINK program. The controller and the state-space model are verified experimentally. Simulation and experimental results verify the effectiveness of the PID controller adaptive by GA to control the angular position of the rotary actuator as compared with the classical PID controller and the compensator controller.     

Modeling and control of a novel electro-hydrostatic actuator with adaptive pump displacement

The variable pump displacement and variable motor speed electro-hydrostatic actuator (EHA), one of the three types of EHAs, has advantages such as short response time, flexible speed regulation, and high efficiency. However, the nonlinearity of its double-input single-output system poses a great challenge for system control. This study proposes a novel EHA with adaptive pump displacement and variable motor speed (EHA-APVM). A closed-loop position is realized using a servomotor. Moreover, the displacement varies with the system pressure; thus, the EHA-APVM is a single-input and single-output system. Firstly, the working principles of the EHA-APVM and the pump used in the system are introduced. Secondly, a nonlinear mathematical model of the proposed EHA-APVM control system is established, and a feedback back-stepping (FBBS) control algorithm is introduced to transform the complex nonlinear system into a linear system on the basis of the back-stepping control theory. Finally, simulation results prove that the EHA-APVM has a quick response and high robustness to variations of the load and the pump displacement. In this work, the size and weight of the motor are significantly reduced because the maximum power requirement is reduced, which is very beneficial for using the actuator in airborne equipment.     

Design and Simulation of Electro-hydrostatic Actuator with a Built-in Power Regulator

The electro-hydrostatic actuator (EHA) is a kind of power-by-wire (PBW) actuator that converts the electrical power into localized hydraulic power for flight control. By removing the central hydraulic power supply together with hydraulic pipes, an EHA's reliability and efficiency are greatly improved but its frequency width and stiffness decreased. To overcome the drawback, this article proposes a novel structure of EHA associated with a power regulator. Composed of a high-pressure accumulator and a proportional valve, it can store and harness the hydraulic power flexibly according to the changing control requirements. The concept of transferred volume is put forward to estimate the capability of the power regulator. The actuator output position can be kept fixed with a hydraulic lock. The compounded control is specially developed to ensure the actuator system to operate in a correct manner. The simulation results indicate that the new-brand actuator results in efficient expanding of the system frequency width with an optimal power supply.     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

辅助动力装置系统进气风门位置控制设计与研究

辅助动力装置系统进气风门位置控制子系统用于地面和空中控制辅助动力装置进气风门的打开和关闭,通常由控制器,作动机构(电动作动器和连杆机构)组成。辅助动力装置系统进气风门位置控制子系统的设计是辅助动力装置控制系统设计的一部分,和辅助动力装置进气风门设计、进气风门气动载荷计算分析及辅助动力装置进气道设计同步进行,相互影响。对某型飞机的辅助动力装置系统进气风门位置控制设计方案进行了介绍,该风门位置控制采用单独的风门控制器,降低了辅助动力装置FADEC(Full Authority Digital Electrical Controller,全权限数字电子控制器,简称FADEC)软硬件设计复杂度,简化了接口设计;并且设计了一种新型辅助动力装置系统进气风门作动机构,该作动机构安装/拆卸方便,可达性好;具有力矩放大功能,且该机构可调节,能输出不同大小的力矩。该进气风门位置控制子系统经过型号验证,对后续型号研制具有较强的指导性。     

无人机综合飞行/推力矢量控制

以某无人机为背景,主要研究大机动时带推力矢量的综合飞行/推进控制系统的设计方法。应用非线性动态逆方法,根据无人机本身具有明显不同时间尺度差异的动力学特性,结合奇异摄动理论将控制变量按照响应快慢分为4个回路进行了控制器的设计与仿真;设计推力矢量控制和气动控制相结合的控制器,实现飞行和推力矢量的控制综合;将无人机的任务转化为对飞行控制的限制条件,对所设计的控制系统进行了数字仿真,结果表明所设计的控制器能够满足飞机做大机动时的控制要求。     

电动静液作动器非线性框图建模与鲁棒控制方法

 阐述了机载电动静液作动器（EHA）的典型工作原理与结构特点,根据其元部件数学方程,建立非线性精确框图模型,完善了EHA补油回路和摩擦特性的描述。通过对系统阻尼、稳态误差及摩擦的仿真分析,设计了一种结合动态压力反馈与变增益控制策略的状态反馈控制器,改善了系统动、静态性能。鲁棒性测试结果反映了系统参数不确定性对性能的影响。     

双变量一体化电动静液作动系统研究

分析了变排量变转速型一体化电动静液作动系统,通过同时控制直流无刷伺服电机转速和伺服泵排量达到改变作动器输出的目的,并建立了其基于状态空间描述的数学模型,根据其双变量相乘的特点对其系统特性进行研究,提出了双变量一体化电动静液作动系统的基本控制方法.     

纳卫星变轨段质量矩姿态控制系统设计

提出应用质量矩控制技术实现纳卫星轨道机动过程中的姿态稳定控制。在设计出质量矩滑块构型后,利用动量和动量矩定理推导了八自由度(DOF)动力学模型,并根据动力学分析结果建立了简化控制模型。以此为基础,基于全局滑模控制理论设计了俯仰偏航通道姿态稳定和滑块位置跟踪的鲁棒控制器,并在参数不确定性条件下对控制系统进行了仿真,结果表明:所设计的二维质量矩控制系统能快速控制卫星姿态,并对系统扰动具有较强的鲁棒性,可以应用于纳卫星变轨段的姿态控制。     

Robust Hybrid Control for Ballistic Missile Longitudinal Autopilot

This paper investigates the boost phase’s longitudinal autopilot of a ballistic missile equipped with thrust vector control. The existing longitudinal autopilot employs time-invariant passive resistor-inductor-capacitor (RLC) network compensator as a control strategy, which does not take into account the time-varying missile dynamics. This may cause the closed-loop system instability in the presence of large disturbance and dynamics uncertainty. Therefore, the existing controller should be redesigned to achieve more stable vehicle response. In this paper, based on gain-scheduling adaptive control strategy, two different types of optimal controllers are proposed. The first controller is gain-scheduled optimal tuning-proportional-integral-derivative (PID) with actuator constraints, which supplies better response but requires a priori knowledge of the system dynamics. Moreover, the controller has oscillatory response in the presence of dynamic uncertainty. Taking this into account, gain-scheduled optimal linear quadratic (LQ) in conjunction with optimal tuning-compensator offers the greatest scope for controller improvement in the presence of dynamic uncertainty and large disturbance. The latter controller is tested through various scenarios for the validated nonlinear dynamic flight model of the real ballistic missile system with autopilot exposed to external disturbances.     

Direct thrust control for multivariable turbofan engine based on affine linear parameter-varying approach

A novel turbofan Direct Thrust Control(DTC) architecture based on Linear ParameterVarying(LPV) approach for a two-spool turbofan engine thrust control is proposed in this paper.Instead of transforming thrust command to shaft speed command and pressure ratio command, the thrust will be directly controlled by an optimal controller with two control variables. LPV model of the engine is established for the designing of thrust estimator and controller. A robust LPV H∞filter is introduced to estimate ...     

Onboard actuator model-based Incremental Nonlinear Dynamic Inversion for quadrotor attitude control: Method and application

This paper addresses the robust attitude control problem for quadrotors subject to model mismatch and disturbances. A dynamic inversion based attitude control scheme is proposed, which consists of an outer loop attitude controller and an inner loop angular acceleration controller. The attitude controller is designed based on the Nonlinear Dynamic Inversion (NDI) to precisely linearize the nonlinear dynamics between the angular acceleration and the attitude. An onboard actuator model-based Incremental Nonlinear Dynamic Inversion (INDI) controller is designed in the angular acceleration control loop to improve the robustness against the model mismatch and disturbances. Meanwhile, the onboard actuator model with a modified structure eliminates the oscillation phenomenon when the sampling rate of the controller is higher than that of the actuator. Numerical simulations and flight tests demonstrate the effectiveness and robustness of the proposed controller in comparison with the PID controller.     

作动器故障下的无人机容错控制方法

在执行任务过程中,无人机的传感器、作动器等均可能出现故障。文章针对常规布局无人机的作动器故障,提出了 1种反步法和控制分配相结合的容错控制方法。首先,建立无人机数学模型,并对作动器故障进行分类和建模;然后,根据模型设计反步最优控制器和基于控制分配的容错控制器;最后,通过仿真验证表明,所设计的容错控制方法能够实现作动器故障下的姿态快速稳定控制,且稳定性好,基本无侧滑角,各操纵面均在约束范围内,达到容错控制要求。     

基于机载实时模型的发动机执行机构 故障状态参数估计

为了对发动机的主燃烧室供油量控制器、喷管喉部面积控制器、风扇进口可调导叶角度控制器、压气机进口可调导叶角度控制器进行故障诊断,建立了基于简化n+1残量方法的非线性机载实时模型,并结合常增益扩展卡尔曼滤波器建立执行机构控制参数估计器,利用非线性部件级模型模拟飞行包线内发动机执行机构的软故障.仿真结果表明:执行机构控制参数估计器在飞行包线内能实现较高精度估计,且具有较好的稳定性.     

自适应阻抗控制在广义主动加载中的应用

 以并联六自由度机构为对象,研究了阻抗控制在广义主动加载中的应用。推导了并联六自由度机构广义力、单缸力和单缸位移之间的阻抗控制数学模型,并分析了稳态误差影响因素;设计了符合现有实验条件的模型参考自适应阻抗控制器(MRAC),该控制器仅通过广义力反馈、单缸力反馈即可实现控制参数的在线修正,并由六自由度机构单缸位移反馈构成闭环控制系统。比较自适应阻抗力控制器和经典力控制器进行了广义主动加载仿真,结果表明所设计的控制器提高了系统动态响应能力,对环境刚度变化鲁棒性强,可以实现实验室条件下广义力的精确稳定跟踪。     

考虑预设性能约束的运输机姿态容错控制

针对运输机舵面故障情况下的姿态容错控制问题,提出了一种考虑预设性能约束的自适应指令滤波增量反步(Adaptive Command-filtered Incremental Backstepping,ACFIBS)容错控制器。首先,构造运输机故障模型,在反步控制设计结构下,通过构造预设性能函数,保证外回路姿态角跟踪误差的动态性能。然后,考虑舵机偏转速率和幅值限制,引入受限指令滤波器和补偿信号,综合考虑气动参数不确定性,采用增量方法设计反步内环控制律。在此基础上,进一步考虑舵面故障情况,引入自适应方法及低通滤波器改进增量反步控制器。最后,通过理论推导和仿真试验验证了控制方法的有效性。仿真结果表明,所设计的控制器具有良好的容错性能,在不同舵面故障条件下均可实现对指令信号的预设性能跟踪,且在参数摄动情况下具有较强的鲁棒性。