苯并噁嗪/ BMI/ 环氧树脂的固化动力学

制备了苯并噁嗪树脂/BMI/环氧树脂三元体系,采用动态DSC分析了三元体系的固化反应过程。并用Kissinger和Ozawa方法分别求得三元体系的反应活化能为89.5 kJ/mol。由Crane理论计算得到该体系的固化反应级数n=0.93级反应;根据计算的动力学参数,建立了三元体系的固化动力学模型。利用所建立的固化动力学模型分别预测了等温和动态条件下,三元体系的固化反应特性。得到了三元体系的固化工艺为180℃/1 h+200℃/2 h+230℃/2 h,后处理工艺为250℃/2 h。     

聚三唑树脂的固化动力学模型

运用分段拟合法所得的固化动力学模型描述了一种新型聚三唑树脂的固化行为。研究表明,该树 脂体系在固化前期符合自催化模型,模型为dα dt =3. 78×1016exp(-10200/ T)α0. 653(1-α)2. 015;在固化后期符合n 级固 化模型,模型为dα dt =3. 34×1016exp(-10200/ T)(1-α)0. 927。聚三唑树脂的固化工艺为:RT→80℃→120℃→150℃。     

RFI用环氧树脂固化动力学研究

用DSC研究了RFI工艺用环氧树脂的固化过程,研究表明：该固化反应较复杂,其反应动力学方程为dα/dt=2.27×10^4exp（-4764.65/T）（1-α）^0.861.为RFI用环氧树脂固化工艺的确定提供了理论依据.     

RFI 用酚醛树脂体系的固化动力学和TTT 图

研制了适合树脂膜熔渗工艺(RFI)的酚醛树脂体系,采用动态DSC技术和固化度的测试,建立了改性树脂体系的固化动力学模型,研究了等温条件下固化度/温度/时间关系以及固化度/玻璃化转变温度关系,通过平板拉丝法研究树脂的凝胶过程,得出凝胶时间和温度之间的关系,回归得到凝胶时的固化度为αgel=53.33％,并以此计算出凝胶时的Tg,gel=48.64℃,在此基础上绘制了该体系的TTT图.     

多官能含氯环氧树脂的合成与性能

合成了一种耐湿热性的多官能环氧树脂3,3′一二氯-4,4′-二氨基二苯基甲烷四缩水甘油胺,并用FT-IR对其结构进行了表征.采用非等温DSC法确定了多官能环氧树脂体系的固化工艺为90℃/1 h+160℃/2 h+190℃/3 h:固化物的分解温度为365.9℃,具有很高的热稳定性和较好的力学性能.     

可溶性改性双马来酰亚胺树脂基体的研究

在双马来酰亚胺/二元胺/改性剂A预聚体系中加入环氧丙烯酸树脂,制备了一种可用作耐热复合材料基体的改性双马来酰亚胺树脂。用DSC研究了该树脂基体的反应特性,并制定出了合适的固化工艺参数:改性树脂基体经140℃/1 h 160℃/1 h 180℃/2 h初固化,于220℃/8 h后固化处理,其热变形温度(HDT)为245℃;该树脂与玻璃纤维制备的单向复合材料层压板的室温拉伸强度、弯曲强度和层间剪切强度分别为1 030 MPa、1 600 MPa和92．1 MPa;180℃下测得弯曲强度保持率为67．8%,层间剪切强度保持率为63．2%,用DMA法测得T_g为273℃。     

TG800碳纤维/双马树脂基预浸料等温固化动力学

为复合材料成型工艺参数制定提供准确信息,采用动态力学分析法(DMTA)对国产TG800碳纤维/802双马树脂基预浸料等温固化动力学进行研究,根据损耗模量E″在恒温扫描过程中出现的拐点可准确确定固化凝胶点。以储能模量E′相对增长率为固化反应速率指标,考察不同恒温阶段反应程度增长模式,并建立了固化反应动力学模型。分别采用Hsich非平衡热力学涨落理论和Avrami方程对预浸料固化反应过程中活化能变化规律进行分析。结果表明:Hsich理论得出TG800/802预浸料反应活化能为49. 5 kJ/mol;Avrami方程得出恒温阶段前期活化能均小于后期,且温度越高对应活化能越低。TG800/802在200℃恒温时前期活化能为78. 8 kJ/mol,小于后期109 kJ/mol,温度升高至240℃后活化能降至32. 4 kJ/mol。通过计算不同恒温阶段固化度佐证了双马树脂固化制度150℃/1 h+180℃/2 h+200℃/4 h的可行性,为TG800/802预浸料的工程化应用提供了技术支撑。     

富氮高能物质BTATz的热分解动力学和分解机理

为获得富氮高能物质3,6-双(1氢-1,2,3,4-四唑-5-氨基)-1,2,4,5-四嗪(BTATz)的热分解动力学参数、热分解机理函数、气相和凝聚相变化,为建立燃烧过程数学模型提供关键性热化学、热力学和化学动力学参数,通过热重(TG)、差示扫描量热(DSC)和气体(固体)原位反应池/快速扫描傅里叶变换红外光谱(RSFTIR)联用技术,研究了BTATz的热分解。实验结果显示BTATz的热分解过程对压强不敏感。基于Ozawa,Kissinger和Coats-Redfern方法,计算获得了BTATz的热分解动力学参数和方程。Kissinger法求得的活化能Ea和指前因子lgA分别为317.41 kJ.mol-1和28.07s-1。热分解反应机理服从n=1.5的Avrami-Erofeev方程,其热分解反应的动力学方程为dαdt=1.5×1028.07exp(-3.8178×104/T)(1-α)[-1n(1-α)]1/3。分析提出了BTATz的热分解机理,BTATz的热分解是从四嗪和四唑环的开环断裂开始的,分解产物又发生二次反应,465℃热分解凝聚相产物为NH4N3,聚胺和嘧嘞胺。     

低温固化非热压罐成型树脂及其复合材料性能

通过DSC、红外光谱、流变仪和力学性能测试等方法,研究了 3228树脂及T700/3228预浸料的性能.结果表明:3228树脂初始固化温度为67.9℃,峰值固化温度为89.5℃;在60℃时具有大于2 h的低黏度平台期,黏度值在20～30 Pa·s;温度大于65℃后表现出低温快速固化的特性;采用60℃预固化1 h,80℃...     

低线胀系数环氧灌封胶的改进与性能

胶黏剂中的填料可以有效提高粘接材料间的线胀系数匹配性,但是分散性和相容性也是需要注意的一个重要问题。本文对填料进行了表面化学改性,采用红外光谱法和元素扫描分析法对填料的改性效果进行了表征。测试结果表明,硅烷偶联剂在填料表面形成了接枝效果。改进后灌封胶的线胀系数从83.9×10~(-6)/K降低到41.8×10~(-6)/K,降低了约50.1%。工艺优化结果显示环氧灌封胶的灌封温度为60℃,操作时长可延长至3 h;固化工艺为65℃/2 h+105℃/4 h+135℃/2 h。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

ν-gap度量及其在飞行控制律评估中的应用

 传统控制律评估方法主要用于单输入单输出（SISO）系统，且对模型参数摄动考虑不够全面,针对这些不足，研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上，给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算，提出ν-gap度量评估控制律的步骤。实例结果表明，该方法不仅克服了上述传统评估方法的缺陷，而且还有根据所求的各摄动影响情况忽略影响小的元素，以减少计算量及可以找到最坏情况下的参数摄动组合等优点。     

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Integrated Entry Guidance for Reusable Launch Vehicle

A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。